• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.437-445
• /
• 2021

This paper proposes an operating frequency design method that limits the voltage applied to aload-side converter during the initial operation of a loosely coupled resonant dual-active bridge (LCR-DAB) converter and an initial operating strategy that applies it. The LCR-DAB converter uses two wireless power transfer coils instead of the high-frequency transformer of the general DAB converter. The wireless power coil has a physical distance of several tens of millimeter or more between the two coils; thus, the LCR-DAB converter is a bidirectional isolated power conversion system that can easily achieve high insulation performance. However, for the initial operation of the LCR-DAB, if the power-side converter is operated at the resonance frequency while the load-side converter is not operating, then a very high voltage due to resonance is applied to the load-side converter, thereby causing damage to the converter. Therefore, a method that can stably charge the DC link voltage of the secondary-side converter during the initial operation is needed. This paper proposes a method to initially charge the secondary-side DC link by operating the primary-side converter at a frequency with limited voltage gain rather than at a steady-state operating frequency. The validity of the proposed frequency design method and initial operating sequence is verified through simulation and experimentation of the 1 KW LCR-DAB converter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.678-683
• /
• 2010

This paper presents a wireless (contactless) charging technique with a new core material called permalloy. For charging portable devices wirelessly, ferrosilicon or ferrite has been conventionally used. Due to high permeability of permalloy, charging efficiency can be significantly improved and subsequently this high efficiency increases charging distance between charger and portable devices. Comparative experimental studies demonstrate that the charging performance and efficiency with permalloy employed are significantly improved. The proposed wireless charging techniques can be used to charge portable devices efficiently.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.79-84
• /
• 2020

Wireless power transfer is more convenient than wired power transfer, but has a shorter transfer distance and lower efficiency. In addition, it is difficult to charge multiple devices simultaneously. In this paper, we propose a method of magnetic beam forming by using multiple transmitters in order to increase transfer distance and improve efficiency of wireless power transfer. To do this, the relationship between the transmitter coil current and magnetic field at the center of receiver coil is modelled, and calculate the optimal transmitter coil current using the characteristics of the pseudoinverse. Finally, the validity of the proposed method is verified by simulation.

• The Journal of the Korea Contents Association
• /
• v.7 no.8
• /
• pp.76-85
• /
• 2007

The mobile content which adopts the subject matter of wired online game with interoperability element is in service. This is one of the plans which are the possibility of benefiting wired online game in game industry. In this paper, interoperability method of game content between wired and wireless classifies this with three branches and it tries to analyze the interrelationship of the interoperability element and interoperability types adopted in many wired online games. And, the development of interoperability server is composed of mobile server which takes charge of I/O process of mobile device and game server records all information of users in the game. With developing the content which is suitable in specific game(Ran-Online), this paper presents the development method of game content through interoperability between wired and wireless.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.607-614
• /
• 2017

In this research, buck converter was designed and manufactured to improve the wireless charging of smartphone through PWM control technology based on micro controller. A feedback control circuit was fabricated using a voltage sensor so that the output voltage follows the reference voltage. The buck converter, 311V is output as 12V, DC voltage 12V is connected wirelessly, and 5V charge voltage is output. We also confirmed the availability of the buck converter for wireless charging of smart phone through experiments.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2008.04a
• /
• pp.247-250
• /
• 2008

최근 무선통신용 LSI는 배터리 수명과 관련하여, 저전력 동작이 중요시되고 있다. 따라서 Digital CMOS 신호처리와 더불어 동작 가능한 SI (Switched-Current) circuit를 이용하는 Current-mode 신호처리가 주목받고 있다. 그러나 SI circuit의 기본인 Current Memory는 Charge Injection에 의한 Clock Feedthrough라는 문제점을 갖고 있기 때문에, 전류 전달에 있어서 오차를 발생시킨다. 본 논문에서는 Current Memory의 문제점인 Clock Feedthrough의 해결방안으로 CMOS Switch의 연결을 검토하였고, 0.25${\mu}m$ CMOS process에서 Memory MOS와 CMOS Switch의 Width의 관계는 simulation 결과를 통하여 확인하였으며, MOS transistor의 관계를 분명히 하여, 설게의 지침을 제공한다.

• Journal of Digital Convergence
• /
• v.17 no.10
• /
• pp.223-232
• /
• 2019

With the development of the information communication industry, the size of the communication device has been reduced to a system that generates a large amount of heat. Therefore, since the amount of heat generated by the wireless equipment is large in the wireless base station, the energy consumption is continuously consumed and the failure of the wireless base station may occur. Therefore, in this study, The study was analyzed. As a research method, we performed base station with a lot of calorific value and electric charge. We selected 25 base stations and obtained data for two weeks. To ensure reliability, the room temperature was kept constant at $27^{\circ}C$, and the control system was installed and equiped for two weeks to obtain the date analysis. In order to calculate the test results in the study method, the instrument was used with a computer, a digital thermometer, and dust measurement. For the date analysis, we conducted a research study on 25 wireless basestations before and after the installation of Control Sysetm.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.4
• /
• pp.109-116
• /
• 2014

In recent, ISM (Industrial Scientific Medical) band that is 2.4GHz band authorized free of charge is being widely used for smart phone, notebook computer, printer and portable multimedia devices. Accordingly, studies have been continuously conducted on the possibility of coexistence among nodes using ISM band. In particular, the interference of IEEE 802.11b based Wi-Fi device using overlapping channel during communication among IEEE 802.15.4 based wireless sensor nodes suitable for low-power, low-speed communication using ISM band causes serious network performance deterioration of wireless sensor networks. This paper examined a method of identifying channel status to avoid interference among wireless communication devices using IEEE 802.11b (Wi-Fi) and other ISM bands during communication among IEEE 802.15.4 based wireless sensor network nodes in ISM band. To identify channels occupied by Wi-Fi traffic, various studies are being conducted that use the RSSI (Received Signal Strength Indicator) value of interference signal obtained through ED (Energy Detection) feature that is one of IEEE 802.15.4 transmitter characteristics. This paper examines an algorithm that identifies the possibility of using more accurate channel by mixing utilization of interference signal and RSSI mean value of interference signal by wireless sensor network nodes. In addition, it verifies such algorithm by using OPNET Network verification simulator.

• Journal of the Korean Chemical Society
• /
• v.49 no.1
• /
• pp.78-82
• /
• 2005

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.168-172
• /
• 2003

This paper presents a non-electrical isolated Prototype of N+X redundant UPS with two-quadrant converter. Proposed topology has multi-functions of battery charge and discharge regulation, operates with a near unity input power factor, compensates unbalanced voltage on U bus capacitors, and regenerates the circulating active power among the inverters into battery or grid. And furthermore, this system adopts a novel wireless parallel operation algorithm of N+X redundant UPS system with no control interconnections. Simulation and experiment results are provided in this paper to prove the validity of proposed topology and wireless control algorithm.