• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.6
• /
• pp.548-555
• /
• 2014

As a considerable, experimental approach, an Auto-carriage type of $CO_2$ welding machine and a MIG(Metal Inert Gas) welding robot under inert gas atmosphere were utilized in order to realize Al 5083 welding applied to hull and relevant components of green Al leisure ships. This study aims at investigating the effect of welding conditions(current, voltage, welding speed, etc) on thermal deformation that occurs as welding operation and tensile characteristics after welding, by using Al 5083, non-ferrous material, applied to manufacturing of co-environmental Al leisure ships. With respect to welding condition to minimize the thermal deformation, 150A and 16V at the wire-feed rate of 6mm/sec were acquired in the process of welding Al 5083 through an auto carriage type of $CO_2$ welding feeder. As to tensile characteristics of Al 5083 welding through a MIG welding robot, most of tensile specimens showed the fracture behavior on HAZ(Heat Affected Zone) located at the area joined with weld metal, except for some cases. Especially, for the case of the Al specimen with 5mm thickness, 284.62MPa of tensile strength and 11.41% of elongation were obtained as an actual allowable tensile stress-strain value. Mostly, after acquiring the optimum welding condition, the relevant welding data and technical requirements might be provided for actual welding operation site and welding procedure specification(WPS).

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.5
• /
• pp.400-409
• /
• 2012

It is not easy to know the accurate mass and mass moment of inertia of robot. Because of this uncertainty, error may exist when we control the robot based on the inaccurate mass information. Moreover the properties of the portable robot can change during its operation. Therefore we developed the motion simulator based on the adaptive control. First, the computed torque control was carried out in order to minimize an error between target angles and real angles. The computed torque control is based on the equation of robot motion, which is derived from the Lagrange-Euler equation. To minimize the error between the real model and the approximated model, the adaptive control was carried out. During this simulation, the interference check was also carried out. The interference check verifies that the robot can move successfully without any collision.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.55-61
• /
• 2009

This study aims for determination of cutting work envelope of an articular robot for H-beam cutting. The robot has its own work envelope. The cutting of piece with groove requires the specific position of the torch which contracts the work envelope. This study suggested the new method to determine the cutting work envelope for this case. The method simplified the problem by use of the combination of inverse kinematics and forward kinematics. The method was used for cutting the H-beam with groove. The cutting work envelope was determined easily. The result was verified by 3D simulation system which implements the articular robot with 6 axes and the H-beam in the virtual shop.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.66-76
• /
• 2002

Automated welding and soldering are an important manufacturing issue in order to lower the cost, increase the quality, and avoid labor problems. An off-line programming, OLP, is one of the powerful methods to solve this kind of diversity problem. Unless an OLP system is ready for the path optimization in welding and soldering, the waste of time and cost is unavoidable due to inefficient paths in welding and soldering processes. Therefore, this study attempts to obtain path optimization using a genetic algorithm based on artificial intelligences. The problem of welding path optimization is defined as a conventional TSP (traveling salesman problem), but still paths have to go through welding lines. An improved genetic algorithm was suggested and the problem was formulated as a TSP problem considering the both end points of each welding line read from database files, and then the transit problem of welding line was solved using the improved suggested genetic algorithm.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.55-62
• /
• 2017

This paper aims to realize additional axes, which increase the processing efficiency of a robot by controlling in harmful environments. Ultimately, this is to create time and energy savings in industrial sites with 6-axis articulated welding robots (RS2). Using $RecurDyn^{(R)}$ a simulation technique is applied. The motion paths of the welding rod are compared for two cases in order to verify the necessity of the additional axes: 1) when there are no additional axes and 2) when there are additional axes during welding using the RS2. For this purpose, the angle variations of the RS2 axes required for the simulation are compared, on the assumption that each of the four points of the welding bed installed on the additional axes of the welding rod in $Solidworks^{(R)}$ is point-welded. Then, actual additional axes equipment is grafted on to the RS2 and the process times compared using $LabVIEW^{(R)}$.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2005.11a
• /
• pp.50-56
• /
• 2005

The robot systems are widely used in the many industrial field as well as welding manufacturing. The essential tasks to operate the welding robot are the acquisition of the position and/or shape of the parent metal. For the seam tracking or the robot tracking, many kinds of contact and non-contact sensors are used. Recently, the vision is most popular. In this paper, the development of the system which measures the shape of the welding part is described. This system uses the line-type structured laser diode and the vision sensor. It includes the correction of radial distortion which is often found in the image taken by the camera with short focal length. The Direct Linear Transformation (DLT) method is used for the camera calibration. The three dimensional shape of the parent metal is obtained after simple linear transformation. Some demos are shown to describe the performance of the developed system.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2003.11a
• /
• pp.185-192
• /
• 2003

Digital Manufacturing-based production could be very effective in shipbuilding in order to save costs and time, to increase safety for workers, and to prevent bottleneck processes in advance. Digital shipbuilding system, a simulation-based production tool, is being developed to achieve such aspects in Korea. To simulate material flow in a subassembly line at a shipyard, the product, process and resources was modeled for the subassembly process which consisted of several sub-processes such as tack welding, piece alignment, tack welding, and robot welding processes. The analysis and modeling were carried out by using the UML(Unified Modeling Language), an object-oriented modeling method as well as IDEF(Integration DEFinition), a functional modeling tool. Initially, the characteristics of the shop resources were analyzed using the shipyard data, and the layout of the subassembly line was designed with the resources. The production process modeling of the subassembly lines was performed using the discrete event simulation method. Using the constructed resource and process model, the productivity and efficiency of the line were investigated. The number of workers and the variations In the resource performance such as that of a new welding robot were examined to simulate the changes in productivity. The bottleneck process floated according to the performance of the new resources. The proposed model was viewed three-dimensionally in a digital environment so that interferences among objects and space allocations for the resources could be easily investigated

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1757-1762
• /
• 2003

For coping with various ship types easily, welding automation using CAD/CAM is demanded and and developed. In this paper we propose a dedicated CAM system which generates MACRO files to control robot manipulators. The paper contains CAD interface, virtual simulation, macro generation and job schedulling. At first, it defines and extracts weldline from CAD data, and generates proper MACRO programs. And it obtains optimum job schedules. This system removes the manual work, and consequently reduces the overall lead time. And it reduces costs and time for developing robot welding programs. This can be expanded to virtual factory simulation technology. Moreover, it is possible to apply this system for automation of Cutting and Painting

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.6
• /
• pp.37-42
• /
• 2007

The purpose of this research is stability estimation of plant structure through classification and recognition about welding flaw in SWP(Spiral Welding Pipe). And, In this research, we used nondestructive test based on ultrasonic test as inspection method, and made up 2-axes inspection robot in order to control of ultrasonic probe on the SWP surface, and programmed to image processing and probabilistic neural network(PNN) classifying code by MATLAB programming. Through this process, we proved efficiency on the system of SWP stability Estimation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.43-44
• /
• 2012