• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.

• Current Photovoltaic Research
• /
• v.11 no.3
• /
• pp.67-74
• /
• 2023

The earth-abundant element-based Cu₂ZnSn(S,Se)₄ (CZTSSe) thin film solar cells (TFSCs) have attracted greater attention in the photovoltaic (PV) community due to their rapid development in device power conversion efficiency (PCE) >13%. In the present work, we demonstrated the fine-tuning of the bandgap in the CZTSSe TFSCs by altering the sulfur (S) to the selenium (Se) chalcogenide ratio. To achieve this, the CZTSSe absorber layers are fabricated with different S/(S+Se) ratios from 0.02 to 0.08 of their weight percentage. Further compositional, morphological, and optoelectronic properties are studied using various characterization techniques. It is observed that the change in the S/(S+Se) ratios has minimal impact on the overall Cu/(Zn+Sn) composition ratio. In contrast, the S and Se content within the CZTSSe absorber layer gets altered with a change in the S/(S+Se) ratio. It also influences the overall absorber quality and gets worse at higher S/(S+Se). Furthermore, the device performance evaluated for similar CZTSSe TFSCs showed a linear increase and decrease in the open circuit voltage (V_oc) and short circuit current density (J_sc) of the device with an increasing S/(S+Se) ratio. The external quantum efficiency (EQE) measured also exhibited a linear blue shift in absorption edge, increasing the bandgap from 1.056 eV to 1.228 eV, respectively.

• Korean Journal of Community Nutrition
• /
• v.28 no.3
• /
• pp.220-234
• /
• 2023

Objectives: This study aimed to assess the adherence to dietary guidelines among college students in the post-COVID-19 era and examine the changes in their dietary habits as the learning environment transitioned from remote to in-person classes. Methods: We conducted a survey involving 327 college students in Daejeon from March to April 2023. The survey questionnaires included various factors, including age, gender, type of residence, frequency of use of delivery food, convenience food, and eating out. In addition, we investigated the extent of adherence to the dietary guidelines for Koreans and the degree of dietary changes following the post-COVID-19 shift in class format were investigated. For comparative analysis of the level of adherence to dietary guidelines in relation to dietary habit changes, an ANOVA and a post hoc Scheffe test were employed. We also performed a multiple linear regression analysis to identify dietary factors influencing the level of adherence to dietary guidelines. Results: The study revealed a high rate of convenience food consumption and a low rate of homemade food intake among students. There was a marked increase in the consumption of processed foods, convenience foods, dining out, sweet foods, high-fat fried foods, beverages, and alcohol following the transition from online to in-person classes. When examining adherence to Korean dietary guidelines, the highest scored practice was 'Hydration', and the lowest was 'Breakfast habit'. Increased consumption of convenience foods, late-night snacks, and dining out were negatively correlated with adherence levels to dietary guidelines, specifically correlating with 'Healthy weight', 'Hydration', 'Breakfast habit', and the total score of adherence. The adoption of 'regular meals' was positively associated with increased adherence levels to dietary guidelines. Conclusions: The transition from remote to in-person classes post-COVID-19 led to increased intake of convenience foods, dining out, sweet foods, high-fat fried foods, and alcohol. The rise in convenience food and late-night snack consumption negatively influenced several aspects of the dietary guidelines adherence, thereby suggesting the need for strategies to encourage healthy dietary habits among college students.

• Journal of the Korean Arthroscopy Society
• /
• v.9 no.2
• /
• pp.148-153
• /
• 2005

Purpose: To analyze the clinical result of the arthroscopic reduction and fixation for the displaced tibial spine fractures in children and report the utility of the arthroscopic treatment with the review of the literature. Methods: Between December 2000 and July 2004, five patients (average age 9.1 years) received an arthroscopic reduction and fixation of displaced tibial spine fracture. A male-to-female ratio was 3:2 and mean follow-up was 38.2$(13{\sim}56)$ months. All five patients were classified type III by Movers and McKeever classification. The average period from injury to operation was 4.8 days $(3{\sim}8days)$, the avulsed fragment was reduced by operative arthroscopy and fixated by pull-out suture in 3 patients and by cannulated screw in 2 patients. Postoperatively long leg cast was applied for 2 weeks, and then gradual range-of-motion exercise was permitted. Full weight-bearing ambulation was permitted after 6 weeks. The clinical evaluation was performed by range of motion, Lachman and pivot shift test, KT-1000 arthrometer, Lysholm knee score and the modified Feagin score. Results: All five patients had no symptom and recovered full range of motion of the affected knees. Lachman test was positive finding of 1+ laxity in one patient, the others were negative, and all patients were negative findings for pivot shift test. The result of KT-1000 arthrometric assessment is mean maximum side-to-side differences 1.9 mm. Average Lysholm knee score was 99.4. All patients had excellent results in modified Feagin score. Conclusion: Arthroscopic reduction and fixation of displaced tibial spine fracture in children showed excellent result without complication. Both pull-out suture fixation and cannulated fixation provide an effective treatment option for fixation of the displaced anterior tibial spine fracture.

• Journal of the Korean Chemical Society
• /
• v.63 no.6
• /
• pp.453-458
• /
• 2019

Synthesis of ZnCo₂O₃ oxide is performed by sol-gel method via nitrate-citrate route. Powder X-ray diffraction (XRD) study shows monoclinic unit cell having lattice parameters: a = 5.721(1) Å, b = 8.073(2) Å, c = 5.670(1) Å, β = 93.221(8)°, space group P_2/m and Z = 4. Average crystallite sizes determined by Scherrer equation are the range ~14-32 nm, whereas SEM micrographs show nano-micro meter size particles formed in ZnCo₂O₃. Endothermic peak at ~798 K in the Differential scanning calorimetric (DSC) trace without weight loss could be due to structural transformation and the endothermic peak ~1143 K with weight loss is due to reversible loss of O₂ in air atmosphere. Energy Dispersive X-ray (EDX) analysis profile shows the presence of elements Zn, Co and O which indicates the purity of the sample. Magnetic measurements in the range of +12 kOe to -12 kOe at 10 K, 77 K, 120 K and at 300 K by PPMS-II Physical Property Measurement System (PPMS) shows hysteresis loops having very low values of the coercivity and retentivity which indicates the weakly ferromagnetic nature of the oxide. Observed X-band EPR isotropic lineshapes at 300 K and 77 K show positive g-shift at g_iso ~2.230 and g_iso ~2.217, respectively which is in agreement with the presence of paramagnetic site Co²⁺(3d⁷) in the oxide. DC conductivity value of 2.875 ×10^-8 S/cm indicates very weakly semiconducting nature of ZnCo₂O₃ at 300 K. DRS absorption bands ~357 nm, ~572 nm, ~619 nm and ~654 nm are due to the d-d transitions ⁴T_1g(⁴F)→²E_g(²G), ⁴T_1g(⁴F)→⁴T_1g(⁴P), ⁴T_1g(⁴F)→⁴A_2g(⁴F), ⁴T_1g(⁴F)→⁴T_2g(⁴F), respectively in octahedral ligand field around Co²⁺ ions. Direct band gap energy, E_g~ 1.5 eV in the oxide is obtained by extrapolating the linear part of the Tauc plot to the energy axis indicates fairly strong semiconducting nature of ZnCo₂O₃.

• Korean Journal of Microbiology
• /
• v.45 no.1
• /
• pp.63-68
• /
• 2009

The exo-polysaccharide producing microorganism, Aureobasidium pullulans IMS-822, was isolated and identified from soil. The viscosity-average molecular weight of exo-polysaccharide was calculated as $8.9{\times}10^5$ by Mark-Houwink equation. The sugar component of exo-polysaccharide was determined as glucose by HPLC analysis. The IR spectra indicated that the exo-polysaccharide has an absorption peak at 890 $cm^{-1}$ for the ${\beta}-configuration$ of D-glucan. The $^{13}C$ NMR signal at ${\delta}$ 86.62 ppm arose from the substituted C-3 of glucose. The signal at ${\delta}$ 72.11 ppm was assigned to C-6 of branched ${\beta}-(1{\to}3)-D-glucosyl$ residues. Viscosity and Congo red reaction indicated that {\beta}-(1{\to}3)(1{\to}6)-glucan$ produced by A. pullulans IMS-822 has a highly ordered hydrogen-bond dependent conformation in aqueous solution, which collapses in strong alkaline solution.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.1
• /
• pp.8-15
• /
• 2020

In the present paper, as a way of reducing heavyweight impact sounds, in particular, among floor impact sounds which have come to the forefront as a social issue recently, a floor joist slab is proposed that is expected to bring an effect of reducing heavyweight impact sounds through a shift in the natural frequency by installing a floor joist on a flat-type slab to increase the rigidity of the floor slab, differently from the existing method that increases the thickness of floor slab, and the heavyweight impact sound characteristics depending on the floor joist height and interval are interpretively analyzed. As a result of the analysis, though a trend is shown where the sound pressure level decreases as the slab thickness of floor joist increases, and as no difference is shown when thickness is above a certain value, it is thought that there is a threshold for the effect of an increase in floor thickness on blockage of heavyweight impact sounds. Also, as an increase in floor rigidity resulting from an increase in the floor joist height and a decrease in the interval does not lead to a consistent increase in the performance of blocking heavyweight impact sounds, it is thought that a different floor joist height and interval should be applied to each type of house to expect optimum performance of blocking heavyweight impact sounds, and an increase of 100mm in the floor joist height or a decrease of about 100mm in the interval is expected to bring an effect of reducing heavyweight impact sounds by about 1dB to 2dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.2
• /
• pp.358-365
• /
• 2007

In this paper, the effects of transmit beamforming on downlink performance in DS-CDMA communication systems are investigated. The uplink and downlink in FDD systems use different carrier frequencies. If the downlink uses the same weighting vectors as the uplink, the antenna beam for downlink is formed with certain DOA shift and it thus affects the beamforming gain. So, the impacts of different frequencies on the downlink beam patterns are studied. One possible algorithm to convert uplink beamforming weights to downlink, which is called frequency-calibrated processing, is also evaluated to reduce the degradation of downlink performance due to different frequencies. Under frequency selective channels, the downlink chooses a PUPW beamforming scheme when the uplink employs a PPPW vectors. To form a beam pattern for a PUPW after combining the downlink PPPWs converted from the uplink PPPWs, three approaches are studied. One method is to consider only one dominant path and thus obtain a single main-beam. In the others, multiple-beams weighted with the magnitudes of all paths and equally weighted with all paths are constructed.

• Korean Journal of Ichthyology
• /
• v.34 no.3
• /
• pp.179-185
• /
• 2022

The feeding habits of Largehead hairtail Trichiurus japonicus was studied using 377 specimens collected in the Yellow Sea of Korea. The specimens ranged from 4.5 to 33.7 cm in Anal length (AL). T. japonicus consumed mainly a piscivore, such as Engraulis japonicus [percent index of relative importance (%IRI) =74.1%]. We calculated the trophic level as 3.84 for T. japonicus. Fishes were the main prey items for all seasons. The main fish prey during autumn and winter was E. japonicus, whereas those during spring and summer was Larimichthys polyactis. Fishes were the main prey items for all size groups (<15 cm, 15~20 cm, 20~25 cm, ≥25 cm). T. japonicus also showed size-related dietary shift from Spratelloides gracilis and E. japonicus to L. polyactis and T. japonicus. As the anal length of T. japonicus increased, the mean number of preys per stomach (mN/ST) and the mean weight of preys per stomach (mW/ST) tended to increased (One-way ANOVA, P<0.05). Seasonal and size-related shifts in dietary composition were investigated by PERMANOVA analysis, which showed significant variations among size classes and seasons.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.1
• /
• pp.19-26
• /
• 2014

This study investigated foot pressure patterns between experienced skiers and intermediate skiers during alpine skiing. Five experienced skiers and five intermediate skiers participated in this study. Foot pressure measurement system was used to measure vertical ground reaction force (vGRF) and contact area under the six plantar regions. Each participant was asked to perform basic parallel turns and carved turns on a $18^{\circ}$ groomed slope. Each right turn was divided into the initiation phase, the steering phase 1 and 2. For the initiation phase of the basic parallel turns, significantly greater contact area was found on the LRF and RRF of the intermediate skiers (p<.05) and significantly greater vGRF was found on the LRF of the intermediate skiers (p<.05). Also significantly greater vGRF and contact area were found on the LRF and RRF of the intermediate skiers at the steering phase 1 (p<.05) and on the LRF of the intermediate skiers at the steering phase 2 (p<.05). For the carved turns, significantly greater vGRF and contact area were found on the LRF and RRF of the intermediate skiers at all three phase (p<.05). On the other hand, significantly greater vGRF was found on the RFF of the experienced skiers at the steering phase 1 (p<.05). Also significantly greater vGRF and contact area were found on the RMF of the experienced skiers at the steering phase 2 (p<.05). In order to increase performance, we suggest that the intermediate skiers should be unweighted at the initiation phase and shift the body weight to the forefoot of the outer foot at the steering phase 1. Also, the outer ski should be loaded more than the both skis at the steering phase 1 and 2.