• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.223-227
• /
• 2002

Polymeric multi-mode optical waveguides were fabricated for parallel optical interconnection. Waveguide structures were molded by a Ni mold master using a hot embossing technique. The Ni mold master was manufactured by LIGA process. Multimode optical waveguides with a 48$\times$47 ${\mu}{\textrm}{m}$$^2$cross-section were produced by a simple two-step process. The propagation losses of the multimode waveguide measured at 0.85 ${\mu}{\textrm}{m}$ and 1.3 ${\mu}{\textrm}{m}$ wavelengths were 0.38 dB/cm and 0.66 dB/cm, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.3
• /
• pp.224-230
• /
• 2009

FIB has been commonly used as a very powerful tool in the semiconductor industry. It is mainly used for mask repair, device correction, failure analysis and IC error correction, etc. Currently, FIB is not being applied to the fabrication of the micro and nano-structured mold, because of low productivity. And also sputtering rate has been required to fabricate 3D shape. In the paper, we studied the FIB-Sputtering rate according to mold materials. And surface roughness characteristics had been analysed for micro or nano mold fabrication. Si wafer, Glassy Carbon, STAVAX and DLC that have been normally considered as good micro or nano mold materials were used in the study.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.25-29
• /
• 2014

In this study, an optical PCB was proposed which can overcome the limitations of the conventional PCB, and a new structure with pluggable lens was considered for a high-efficient passive alignment. The structure was a lens-added optical waveguide for the improvement of misalignment between the lens and the waveguide in the alignment. Also, as it had a barrier-type structure to prevent the surface damage of the lens by desorption, the high-efficient passive alignment can be realized. The structure was designed by optimizing the simulation and the fabrication process of the pluggable lens structure was conducted using the repetitive photolithography and the thermal reflow. The optical waveguide with the lens-integrated pluggable interconnection was fabricated by the imprint process using the polydimethylsiloxane(PDMS) replica mold. Therefore, we confirmed the possibility of pluggable lens-added optical waveguide structure fabrication for high-efficient passive alignment.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.79-84
• /
• 2005

To increase the tolerance for passive fiber alignment, a single mode polymer waveguide with a large core structure is demonstrated. The large core waveguide is designed to have a mode profile comparable to that of a thermally expanded core (TEC) fiber, and it can be connected to a high-contrast waveguide through an adiabatic transition taper structure. From a waveguide with a rectangular core of 25 ${\times}$ 25 ${\mu}{\textrm}{m}$$^2$, a single mode propagation is observed when the index contrast is as low as 0.0005. A UV-cured injection molding method is used to fabricate the thick core structure. Due to the large mode size, the insertion loss of the device is below 0.5 dB until the lateral displacement of the TEC fiber is 4.5 ${\mu}{\textrm}{m}$. The low insertion loss is important for reproducible passive alignment.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.867-871
• /
• 2012

In this paper, we proposed and demonstrated a low loss $1{\times}4$ type plastic optical fiber(POF) coupler incorporating a polymer tapering waveguide region. To avoid leakage loss at the interfaces between the POF and the polymer waveguide, we employed two POF transition regions, in which the cross section of the POF is adiabatically converted from a circular to a rectangular shape without change of its cross-section area. The device was fabricated based on a injection mold made of a silicon rubber. The fabricated POF coupler showed 1.33 dB of excess loss and 2.2 dB of flatness.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.315-318
• /
• 1999

As low-cost optical waveguides of optical interconnects, we fabricate multimode optical waveguides using a molding process The core size of a optical waveguide is 47 ${\mu}{\textrm}{m}$ $\times$ 41 ${\mu}{\textrm}{m}$. We use the photoresist AZ9260 as a master, polydimethyl-siloxane (PDMS) as a mold. In transferring process to polymeric material, we employ a modified micro-transfer molding process. All processes are simple and low-cost.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.317-322
• /
• 2006

A polymeric arrayed waveguide grating (AWG) has been proposed and demonstrated by exploiting the nanoimprint method. A PDMS(polydimethylsiloxane) stamp with device patterns engraved was developed out of a master mold made of quartz glass. The device was fabricated by transferring the pattern in the PDMS stamp to a spin-coated polymer film without using any etching process. The device had 8 output channels, while the center wavelengths of each output channel were positioned from 1543.7 nm to 1548.3 nm with the spacing of 0.8 nm. The achieved average channel crosstalk and the 3-dB bandwidth were about 10 dB and 0.8 nm respectively.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.149-154
• /
• 2007

Bragg reflecting waveguide devices have been fabricated on a flexible polymer substrate utilizing a post lift-off process which could Provide excellent uniformity of grating Patterns on Plastic film. The 510 m Period Bragg grating pattern is made by two methods. In the first sample the grating is fabricated by exposing the laser interference pattern on a photoresist, and then it is inscribed by $O_2$ plasma etching. The grating pattern of the second sample is formed by a PDMS soft mold imprinting process. The selective adhesion property of SU-8 material for Au and Si surfaces is utilized to prepare a 100-mm thick plastic substrate. Single mode waveguide is fabricated on the plastic substrate using polymer materials with refractive indices of 1.540 and 1.430 for the core and the cladding layers, respectively. The Bragg grating on Plastic substrate does not show any degradation in its spectral response compared to the reference sample made on a silicon wafer.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1526-1531
• /
• 2007

Data transmission capacity that is required in 2010 is forecasted that increase by optical communication capacity more than present centuple, and is doing increased demand of optical communication related industry product present. Specially, Lid glass' application that is one of optical communication parts is used in optical communication parts manufacture of Fiber array, Ferrule array, Fanout Black, Silica optical waveguide chip and splitter etc. Also, it is used widely for communication network system, CATV, ATM-PON, FTTH and system. But, Lid glass need much processing times and becomes cause in rising prices of optical communication parts because production cost is expensive. The objectives, of this work is to suggest the micro concave and convex pattern manufacturing technology on borosilicate plate using high temperature and compression molding method. As a result, could developed micro pattern Mold more than 5 pattern, and reduce Lid Glass manufacture cycle time.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.441-446
• /
• 2007

Outcoupling efficiency of the OLED device is improved by incorporating both a microlens array and a diffractive grating pattern. The microlens array improves the light transmission at the interface of glass and air, and the diffractive grating outcouples the guided mode propagating at the waveguide, which consists of ITO and organic layers. By using the PDMS soft mold imprinting method, the microlens array is fabricated on the glass substrate. The diffractive grating pattern is directly fabricated on the ITO surface by using laser interferometry. A microlens array with a diameter of $10{\mu}m$ improves the light coupling efficiency by 22%. The diffractive grating made of TSMR photoresist enhances the luminance power efficiency by 41% at a current density of $20mA/cm^2$.