• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2017년도 추계학술대회
• /
• pp.19-21
• /
• 2017

Ship maneuvering performance is usually estimated in calm water conditions which provide valuable information about the ship maneuvering characteristics at the early design stage. However, the course-keeping ability and the maneuvering performance of a ship can be significantly affected by the presence of waves when ship maneuvers in real sea condition. Therefore, it is necessary to understand the maneuvering behavior of a ship in waves in the viewpoint of ship safety in the design stage. In this study, the force and yaw moment acting on a moving ship in regular waves with different wave length and wave direction will be performed in the square wave tank in Changwon National University. The results of this study can be used to help a person to design a ship hull with the best ship maneuverability in waves and disseminate knowledge on predicting ship maneuvering in regular waves in various wave directions.

• 한국해양공학회지
• /
• 제35권1호
• /
• pp.13-23
• /
• 2021

Since the introduction of the mandatory energy efficiency design index (EEDI), several studies have been conducted on the maneuverability of waves owing to the decrease in engine power. However, most studies have used the mean wave force during a single cycle to evaluate maneuverability and investigated the turning performance. In this study, we calculated the external force in accordance with the angle of incidence of the wave width and wavelengths encountered by KVLCC2 (KRISO very large crude-oil carrier) operating at low speeds in regular waves using computational fluid dynamics (CFD). We compare the model test results with those published in other papers. Based on the external force calculated using CFD, an external force that varies according to the phase of the wave that meets the hull was derived, and based on the derived external force and MMG control simulation, a maneuvering simulation model was constructed. Using this method, a weather vaning simulation was performed in regular waves to evaluate the course-keeping ability of KVLCC2 in waves. The results confirmed that there was a difference in the operating trajectory according to the wavelength and phase of the waves encountered.

• 대한토목학회논문집
• /
• 제29권1B호
• /
• pp.83-90
• /
• 2009

본 연구는 잔교를 설계할 때 수리모형실험을 통하여 잔교상판에 작용하는 양압력 분포 특성에 대해 기술하였다. 양압력이 상판하부에 작용할 때 압축공기 유출의 유무에 따라 양압력이 작용하는 형상이 다르고 양압력의 크기가 다르게 분포하고 있음을 알았다. 동일 Block 상판내의 양압력분포는 상판의 중심점과 가장자리에서 동일한 분포를 하지 않는 결과를 얻었다. 양압력 분포특성은 잔교길이인 무차원(l/L), 파형경사(H/L), 공간(D/H)에 의해 영향을 받는다. 양압력에 영향을 미치는 무차원 요소(H/L)은 양압력의 최대치를 결정하는 D/H의 값이 존재하고 있다는 것을 알았다. 동일한 D/H인 경우도 양압력은 파형경사에 따라서 변화하고 있다. 즉, H/L이 클수록 (D/H)이 작기 때문에 잔교를 설계할 때 $D_{max}$가 되는 Clearance가 생기지 않는 상판높이를 정하는 것이 안전한 설계가 된다. 압축공기가 양압력에 미치는 영향을 검토한 결과 양압력이 크게 작용하는 On-shore에서는 Off-shore보다 압축공기에 의한 양압력의 저감효과가 크게 발생하고 있다. 상판에 작용하는 양압력을 저감시키기 위해서는 압축공기 유출을 방지하는 상판설계가 필요하다.

• 한국해안·해양공학회논문집
• /
• 제26권5호
• /
• pp.335-341
• /
• 2014

이 연구에서는 단면 수리모형실험을 통해 파의 여러 위상에 따라 단일 및 이중유수실 유공케이슨 방파제의 연직벽에 작용하는 최대 수평파력을 계측하고 그 크기를 서로 비교하였다. 본 실험 자료 분석 결과 이중유수실 케이슨의 유수실 전체 폭이 단일유수실의 폭과 동일한 경우 이중유수실 케이슨에 작용하는 총 수평파력이 평균적으로 9.6% 작은 것으로 나타났다. 이러한 파력 저감 효과는 이중유수실 케이슨 방파제의 유공 전면벽과 무공 후면벽 사이에 위치한 유공 중간벽에서 파 에너지가 소산되기 때문인 것으로 파악되었다.

• 소성∙가공
• /
• 제10권6호
• /
• pp.449-456
• /
• 2001

The concept of stress wave was introduced through the quantized kinetic energy which is related to the potentional energy change of atom, molecular bond energy. Differentiated molecular bond energy $\varphi$() by the lst order displacement u becomes force F(F = d$\varphi$($u_i$)/du), if resversely stated, causing physically atomic displacement $u_i$. Such physical phenomena lead stress(force/area of applied force) can be expressed by wave equation of linearly quantized physical property. Through the stress wave concept, formation of dislocation, which could not explained easily from a theory of continuum mechanics, can be explained. Moreover, this linearly quantized stress wave equation with a stress concept for grains in a crystalline solid was applied to three typical metallic microstructures and a simple shape. The result appears to be a product from well treated equations of a quantized stress wave. From this result, it can be expected to answer the reason why the defect free and very fine diameters of long crystalline shapes exhibit ideal tensile strength of materials.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.889-901
• /
• 2021

The tension of cables and motion response significantly affect safety of an immersed tunnel element in the immersion process. To investigate those, a hydrodynamic scale-model test was carried out and the model experiments was conducted under wind, current and wave loads simultaneously. The immersion standby (the process that the position of the immersed tunnel element should be located before the immersion process) and immersion process conditions have been conducted and illustrated. At the immersion standby conditions, the maximum force of the cables and motion is much larger at the side of incoming wind, wave and current, the maximum force of Element-6 (6 cables directly tie on the element) is larger than for Pontoon-8 (8 cables tie on pontoon of the element), and the flexible connection can reduce the maximum force of the mooring cables and motion of element (i.e. sway is expecting to decrease approximate 40%). The maximum force of the mooring cables increases with the increase of current speed, wave height, and water depth. The motion of immersed tunnel element increases with increase of wave height and water depth, and the current speed had little effect on it. At the immersion process condition, the maximum force of the cables decrease with the increase of immersion depth, and dramatically increase with the increase of wave height (i.e. the tension of cable F4 of pontoons at wave height of 1.5 m (83.3t) is approximately four times that at wave height of 0.8 m). The current speed has no much effect on the maximum force of the cables. The weight has little effect on the maximum force of the mooring cables, and the maximum force of hoisting cables increase with the increase of weight. The maximum value of six-freedom motion amplitude of the immersed tunnel element decreases with the increase of immersion depth, increase with the increase of current speed and wave height (i.e. the roll motion at wave height of 1.5 m is two times that at wave height of 0.8 m). The weight has little effect on the maximum motion amplitude of the immersed tunnel element. The results are significant for the immersion safety of element in engineering practical construction process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1266-1269
• /
• 2004

With increasingly wide needs for a new energy source, many operation types of a wave-forced generation have been studied. To obtain an economically avaliable energy, it is imperative that the speed of the in put wave should be increased by a proper mechanism. In this study, we propose a new speed-increaser mechanism for the wave-force generation using a well-known Stephenson mechanism. In this paper, we have analysed kinematically the proposed speed-increasing mechanism. then a computer program based on the C++ language is developed to prove the validity of our mechanism and to simulate a wave-forced generation.

• 한국해안·해양공학회논문집
• /
• 제33권6호
• /
• pp.275-286
• /
• 2021

본 연구에서는 기존에 선형파 이론으로 제시된 반무한방파제 주변의 회절에 대한 해를 중첩하여 직립 이안제 주변에 발생하는 회절에 관한 해석해를 제시하였다. 그리고, 이를 이용하여 이안제 전면과 후면, 그리고 전·후면에 작용하는 합성파력에 대한 해를 유도하였다. 이안제 전면과 후면에서는 회절파와 중복파, 이안제 양쪽에서 회절한 회절파와 회절파 사이의 간섭에 의해 상대진폭이 공간상에서 주기적으로 변하는 양상을 보였다. 규칙파, 일방향 불규칙파 및 다방향 불규칙파를 대상으로 직립 이안제에 작용하는 파력을 검토하였다. 규칙파 내습시 이안제 전·후면의 파력을 모두 고려한 최대 합성파력의 경우 회절을 고려하지 않았을 경우에 비해 최대 1.6배까지 파력이 증가하는 것으로 나타났다. 이는 Jung et al.(2021)이 반무한 방파제에 대해 회절효과를 고려하여 검토한 결과인 1.34배보다 큰 수치이다. 이안제에 작용하는 최대파력은 규칙파, 일방향 불규칙파, 다방향 불규칙파 순으로 크게 계산되었다. 파랑이 비스듬히 입사하는 경우 이안제에 수직으로 입사하는 경우보다 최대파력이 크게 나타나는 경우도 발견되었다. 따라서, 이안제를 설계할 때, 회절효과, 이안제 전·후면에 작용하는 파력, 파랑의 입사각의 고려가 중요함을 알 수 있다.

• Ocean Systems Engineering
• /
• 제4권3호
• /
• pp.169-183
• /
• 2014

For the reliable design of substructure supporting offshore wind turbines it is very important to reduce the effects of wave forces. Since the substructure is strongly influenced by the effects of wave forces as the size of substructure increases. In the present study, the hybrid substructure with multi-cylinder is newly suggested to reduce the effects of wave forces. Using diffraction theory the scattering waves in a fluid region are expressed by an Eigenfunction expansion method with three dimensional potential theory to calculate the wave force acting on the hybrid substructure. The wave force and wave run-up acting on the hybrid substructure is presented to examine the water wave interaction according to the variation of cylindrical size and the distance among cylinders. It is found that the suggested hybrid substructure with multi-cylinder is very useful to reduce the effects of wave forces acting on the substructure for offshore wind turbines.

• 한국해양공학회지
• /
• 제36권6호
• /
• pp.390-402
• /
• 2022

Offshore wind energy has become a major energy source, and various studies are underway to increase the economic feasibility of floating offshore wind turbines (FOWT). In this study, the characteristics of wave-induced motion of a combined wind-wave energy platform were analyzed to reduce the variability of energy extraction. A user subroutine was developed, and numerical analysis was performed in connection with the ANSYS-AQWA hydrodynamic program in the time domain. A platform combining the TLP-type FOWT and the Wavestar-type wave energy converter (WEC) was proposed. Each motion response of the platform on the second-order wave load, the effect of WEC attachment and Power take-off (PTO) force were analyzed. The mooring line tension according to the installation location was also analyzed. The vertical motion of a single FOWT was increased approximately three times due to the second-order sum-frequency wave load. The PTO force of the WEC played as a vertical motion damper for the combined platform. The tension of the mooring lines in front of the incident wave direction was dominantly affected by the pitch of the platform, and the mooring lines located at the side of the platform were mainly affected by the heave of the platform.