• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.321-328
• /
• 2002

Various geosynthetics used as liners or the Protection layers are installed in the solid waste landfill. The interface shear strength between geosynthetics installed at the slope of the landfill is a very important variable for the safe design of bottom and cover systems in the solid waste landfill. The interface shear strengths between (1) Geomembrane(GM)/Geotexile(GT) and (2) Geomembrane(GM)/Geosynthetic Clay Liner(GCL) were estimated by a large direct shear test in this study and were evaluated by the Mohr-Coulomb failure criterion. Especially, this research is focused on the effect of water which exists between geosynthetics because interfaces become easily wet or hydrated by rain, leachate and groundwater beneath liners. The strength reduction at large displacement and the effects of the magnitude of normal stresses and GCL hydration methods also investigated. The test results showed that the interface shear strength and shear behavior varied depending upon the magnitude of normal stresses, water at the interface, and hydration methods. Summary of secant friction angles, which could be used as reference values at a site where similar geosynthetics are installed, together with normal stress and hydration condition are presented.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.142-155
• /
• 1992

Numerical analysis is performed for the unsteady axisymmetric two dimensional phase change problem of freezing of water around a vertical tube. Heat conduction in the tube wall and solid phase, natural convection in liquid phase and volume expansion caused by density difference between solid and liquid phases are included in the numerical analysis. Existing correlation is used for estimating density-temperature relation of water, and the effect of volume expansion is reflected as fluid velocity at the interface and the free surface. As pure water has maximum density at 4.deg. C, it is found that there exists an initial temperature at which the flow direction reverses near the interface and by this effect the slope of interface becomes reversed depending on the initial temperature of water. By considering natural convection and solid-liquid density difference in the calculation, their effects on phase change process are studied and the effects of various parameters are also studied quantitatively.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.1
• /
• pp.79-89
• /
• 2002

Various geosynthetics used as liners or protection layers are installed in the solid waste landfills. The interface shear strength between geosynthetics installed at the slope of the landfill is a very important variable for the safe design of the bottom and cover systems in the solid waste landfills. The interface shear strength between Geomembrane and Geotexile is estimated by a large direct shear test in this study, The effects of normal stress, water existing between geosynthetics and surface condition of Geomembrae, i.e. smooth or textured, were investigated. The test results show that the effect varied depending on the level of normal stress and the type of geosynthetic combinations. The shear strength was evaluated by the Mohr-Coulomb failure criterion in this research. The shear strength parameters obtained from tests considering the site specific conditions such as normal stress, dry or wet, and surface condition of geosynthetic should be applied to the design of geosynthetics installed at the slope of the landfill to construct a safe solid waste landfill.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1845-1852
• /
• 2001

This paper deals with the experiment to obtain quantitative information about conditions of the interface between a water drop and surrounding oil. Velocity distributions in very close region of the interface are measured by introducing a new illumination technique and a telecentric lens. It enables precise measurements of velocity distributions in the close region to the interface. Although the measured velocity distributions exhibit strong influence from the solid wall of an experimental tube, the coincidence of inner and outside velocities on the interface is clearly confirmed for the clean interface. The shearing stresses on the interface, which are proportional to the velocity gradient normal to the interface, clearly show conditions of contaminated interface, which can be divided into two parts. From front stagnation point to somewhere near a separation point, the distribution of shearing stresses is well coincide with that of the Hadamard's analytical solution, while the distribution on the latter part of the interface sows quite different feature, which is supposed to be strongly influenced by contamination of the surface.

• Tribology and Lubricants
• /
• v.35 no.2
• /
• pp.94-98
• /
• 2019

The riblet structure like shark skin has been widely studied owing to its drag reduction and anti-fouling properties. In this study we simulated the wettability of an oil droplet on a riblet surface. We developed a numerical analysis method using the Wenzel equation and Cassie-Baxter equation that can estimate the contact angle with a penetrated depth of the droplet on rough surfaces. Riblet surfaces with nine scales composed of five hemi-elliptical ribs are generated numerically. The variation of contact angles with fractional depth of penetration for the generated riblet surfaces with and without coatings is demonstrated in the condition of solid-air-oil and solid-water-oil interfaces. The contact angle for the uncoated surface decreases with increasing fractional depth of penetration more drastically than that for the coated surface. For the effect of surface roughness on the contact angle of the droplet, the oleophilic surface gives lower contact angle when the surface is rougher, whereas the oleoophobic surface gives higher contact angle with higher roughness To verify the analysis results, the wetting angle was measured in the solid-air-oil interface and solid-water-oil interface for the shark-skin template and shark-skin replica. The effects of teflon coating were also evaluated. It is shown that the simulation results cover the experimental ones.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.8
• /
• pp.700-706
• /
• 1996

We present the results of molecular dynamics simulations of monolayers of long-chain alkyl thiol [S(CH2)15CH3] molecules on an air-solid interface using the extended collapsed atom model for the chain-molecule and a gold surface for the solid surface. Several molecular dynamics simulations have been performed on monolayers with areas per molecule ranging from 18.30 to 32.10 Å2/molecule. It is found that there exist three possible transitions: a continuous transition characterized by a change in molecular configuration without change in lattice structure, a sudden transition characterized by the distinct lattice defects and perfect islands, and a third transition characterized by the appearance of a random, liquid-like state. The analysis of probability distributions of the segments shows that the structure of the chain-molecules at the air-solid interface is completely different from that at the air-water interface in the view of the degree of overlap of the probability distributions of the neighbor segments. The calculated diffusion coefficients of the chain-molecules on the monolayers seem to be not directly related to any one of the three transitions. However, the large diffusion of the molecules enhanced by the increment of the area per molecule may induce the second transition.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1424-1427
• /
• 1996

The pressure-area isotherm(${\pi}$-A isotherm) of 8A5H(4-octyl-4'-(5-Carboxyl-pentamethyleneoxy)-azobenzene) at the air/water interface were obtained. Using the Xe/Hg Xe 500w(93' model 68811), an activities of molecule at the air/water interface were certified. In addition, using a current-measuring technique, we investigated the abrupt changes of a current observed at the liquid-to-solid phase transition in a current-area (I-A) isotherm of a fatty acid monolayer at the air/water interface

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.647-653
• /
• 2013

The evaporation characteristics of nanofluid droplets on a heated solid surface were experimentally investigated. The experiments were conducted using pure water and a nanofluid of water mixed with CuO nanoparticles, and the solid surface was made of a copper block heated by a nine cartridge heater. The experimental results showed that the evaporation rate of the nanofluid droplet was higher than that of the pure water droplet on the heated solid surface because nanoparticles increased the thermal conductivity of the nanofluid. Furthermore, it was found that the evaporation rate of the nanofluid droplet increased with the solid surface roughness. This may be because the actual area of the liquid-solid interface increased with the solid surface roughness.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.54-57
• /
• 2011

In this paper we present an algorithm about how to simulate two dimensional dam breaking with lattice Boltzmann method (LBM). LBM considers a typical volume element of fluid to be composed of a collection of particles that represented by a particle velocity distribution function for each fluid component at each grid point. We use the modified Lattice Boltzmann Method for incompressible fluid. This paper will represent detailed information on single phase flow which considers only the water instead of both air and water. Interface treatment and conservation of mass are the most important things in simulating free surface where the Interface is treated by mass exchange with the water region. We consider the surface tension on the interface and also bounce back boundary condition for the treatment of solid obstacles. We will compare the results of the simulation with some methods and experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.198-201
• /
• 1994

Stability improvement of fragile LB films was attempted by polyion complexation of monolayers at the air-water interface and crosslinking of the resulting LB films. The spreading polymers were synthesized by radical copolymerization of monoalkyl itaconate with oligoethyleneglycol methyl vinylether, and poly(allylamine) was employed as the subphase polymer. Formation and characteristic of the monolayers were comfirmed by surface pressure-area($\pi$-A) isotherms. The two different polymers formed polyion-complexed monolayer through the formation of carboxylate/ammonium salt at the air-water interface. Y-type deposition occurred on solid substrates, and the transfer ratio was over 0.7. Pores (diameter, 0.1$\mu\textrm{m}$) of a membrane filter could be covered by polyion-complexed 6 layers. Interactions of the polymers with metal ions were investigated of the air-water interface and in the LB films. The structure change and macroscope morphology of the LB films were confirmed by FT-lR and SEM, respective1y.