• Journal of Magnetics
• /
• 제16권4호
• /
• pp.323-327
• /
• 2011

By means of Monte Carlo simulation, we investigate the effects of interface roughness and temperature on the exchange bias and coercivity in ferromagnetic (FM)/antiferromagnetic (AFM) bilayers. Both exchange bias and coercivity are strongly dependent on interface roughness. For a perfect uncompensated interface a domain wall is formed in the AFM system during FM reversal, which results in a very small exchange bias. However, a finite interface roughness leads to a finite value of the exchange bias due to the existence of pinned spins at the AFM surface adjacent to the mixed interface. It is observed that the exchange bias decreases with increasing temperature, consistent with the experimental results. It is also observed that a bump in coercivity occurs around the blocking temperature.

• 설비공학논문집
• /
• 제4권3호
• /
• pp.155-162
• /
• 1992

Theoritical Study is performed on heat transfer and fluid flow induced by square-ribbed roughness elements in a concentric annulus. The fluid properties were assumed to be constant, and the radius($r_m$) of the maximum speed point was found by using the principle of equation of Leung and Labib. The Nusselt number and friction factor as a function of the Reynolds number($R_e=10^4$, $5{\times}10^4$, $7{\times}10^4$, $10^5$) in artifical roughness $S/{\epsilon}=5,10,20,30$, $P/{\epsilon}=2,5,8$ and prandtl number = 0.72 have been discussed. In this study, it has been found that the Nusselt number and friction factor of rough wall are larger than those of smooth ones.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.1077-1088
• /
• 2006

This paper describes a numerical investigation on the performance deteriorations of a low speed, single-stage axial turbine due to use of rough blades. Numerical calculations have been carried out with a commercial CFD code, CFX-Tascflow, by using a modified wall function to implement rough surfaces on the stator vane and rotor blade. To assess the stage performance variations corresponding to 5 equivalent sand-grain roughness heights from a transition ally rough regime to a fully rough regime, stage work coefficient and total to static efficiency were chosen. Numerical results showed that both work coefficient and stage efficiency reduced as roughness height increased. Higher surface roughness induced higher blade loading both on the stator and rotor which in turn resulted in higher deviation angles and corresponding work coefficient reductions. Although, deviation angle changes were small, a simple sensitivity analysis suggested that their contributions on work coefficient reductions were substantial. Higher profile loss coefficients were predicted by higher roughness heights, especially on the suction surface of the stator and rotor. Furthermore sensitivity analysis similar to the above, suggested that additional profile loss generations due to roughness were accountable for efficiency reductions.

• 한국터널지하공간학회 논문집
• /
• 제14권4호
• /
• pp.321-336
• /
• 2012

암반 절리면과 같이 입자와 연속체 평면의 접촉면에서의 전단거동은 전체 구조물의 거동을 지배할 수 있다. 암반설계의 효율을 높이기 위해서는 입자와 연속체 평면의 접촉면 전단거동 메커니즘에 대한 기초적인 이해와 접촉면 전단강도를 정확하게 산정하는 것이 필수적이다. 본 연구에서는 연속체 평면의 표면 파쇄가 미치는 영향을 알아보기 위하여 개별요소법 수치해석 프로그램인 $PFC^{2D}$를 사용하였다. 표면 거칠기는 매끄러운 평면, 중간 거칠기 평면, 거친 평면의 세 가지로 구분하였다. 입자의 형상은 원형의 one ball 모델과 삼각형 형상의 3 ball 모델로 구성하였다. 평면은 파쇄가 불가능한 경계요소 연속체 모델과 파쇄가 가능한 입자요소 연속체 모델로 각각 구성하였다. 수치해석 결과, 입자요소 모델의 결합강도가 작을수록 파쇄가 빨리 발생하여 큰 결합강도를 가진 연속체 모델보다 작은 접촉면 전단강도를 보였다. 돌출부의 파쇄가 발생한 후, 접촉면 전단강도는 수렴하는 경향을 보이며, 결합강도가 클수록 돌출부의 파쇄가 적게 발생하였다. 또한 경계요소 연속체 모델이 입자요소 연속체 모델보다 큰 접촉면 마찰각을 나타냈고, 모든 입자 모델에서 연속체의 표면 거칠기가 거칠수록 큰 접촉면 마찰각이 나타났다. 이러한 결과로부터 연속체 평면의 거칠기 및 평면 파쇄가 입자와 평면의 접촉면 전단거동 특성에 미치는 영향을 확인하였다.

• 한국안전학회지
• /
• 제28권5호
• /
• pp.54-60
• /
• 2013

In this study, a finite element model based on the SU/PG scheme was developed to solve shallow-water equations and the influences of parameters and internal boundary conditions on depth-averaged flow behavior were investigated. To analyze the effect of roughness coefficient and eddy viscosity on flow characteristics, the developed model was applied to rectangular meandering channel with two bends, and transverse velocities and water depth distributions were examined. As the roughness coefficient adjacent to wall increased, the velocities near the wall decreased, and the reduced velocities were compensated by the expanding mid-channel velocities. In addition, the flow characteristics around a circular cylinder were analyzed by varying the internal boundary conditions as free slip and no slip. The assignment of slip condition changed the velocity distribution on the cylinder surface and reduced the magnitude of the shear stress up to one third.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.349-354
• /
• 2001

In this study, we investigated the effect of the impacting ang1e of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozz1e up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA#600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2MPa

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2443-2453
• /
• 1994

The structure of turbulence of fully developed flow through four concentric annuli with the rough outer wall was investigated experimentally for a Reynolds number range Re=15, 000-93, 000. Turbulence intensities were measured in three(u, v, w) directions, and turbulence shear stresses in annuli of radius=0.13, 0.26, 0.4 and 0.56, respectively. Due to the square roughness element attached periodically along the axial direction, the radial velocity fluctuations show similar distribution regardless of the different .alpha.cases. However, the axial and circumferential velocity fluctuation profiles demonstrate the longitudinal turbulence structures are strongly influenced by the .alpha. values. The turbulent eddy viscosity deduced form mean velocity distributions and the measured Reynolds shear stresses are also presented and discussed.

• International Journal of Fluid Machinery and Systems
• /
• 제10권3호
• /
• pp.227-239
• /
• 2017

The accuracy of turbulence models for the Reynolds-Averaged Navier-Stokes (RANS) equations in rough-wall flows is evaluated using data from large-eddy simulations (LES) of boundary layers with favourable and adverse pressure gradients. Some features of the flow (such as flow reversal in the roughness sublayer) cannot be captured accurately by any model, due to the fundamental model formulation. In mild pressure gradients most RANS models are sufficiently accurate for engineering applications, but if strong favourable or adverse pressure gradients are applied (especially those leading to separation) the model performance rapidly degrades.

• 한국유체기계학회 논문집
• /
• 제7권5호
• /
• pp.7-12
• /
• 2004

Multi-path ultrasonic flowrate measuring technology is being received much attentions from a variety of industrial fields to exactly measure the flowrate. Multi-path ultrasonic flowmeter has much advantage since it has no moving parts and little pressure loss. It offers good accuracy, repeatability, linearity and turn-down ratio can be over 1:50. The present study investigates flowrate integration errors using weighting factors. A theoretical flow model uses power law to describe a fully developed velocity profiles and wall roughness is changed. Gaussian, Chebyshev, and Tailor methods are used to integrate line-average velocities. The obtained results show that Chebyshev method in 2, 4-path arrangement and Gaussian method in 3, 5-path arrangement are not affected for wall roughness changes.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.154-160
• /
• 2003

Multi-path ultrasonic flowrate measuring technology is being received much attentions from a variety of industrial fields to exactly measure the flowmeter. Multi-path ultrasonic flowmeter has much advantage since it has no moving parts and not occurred pressure loss. It offers good accuracy, repeatability, linearity and Tum-down ratio can measure over 1:50. The present study investigates flowrate integration errors using weighting factors. A theoretical flow model uses power law to describe a fully developed velocity profiles and wall roughness changes. The methods of weighting factor simulate three configurations of measuring location of gaussian, chebyshev and tailor method. The obtained results show that many chord arrangements are not affected for wall roughness changes and can measure accurate flowrate.