• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.168.1-168.1
• /
• 2014

We developed poly (3,4-ethylene dioxylene thiophene):poly (styrene sulfonic acid) (PEDOT:PSS)-free organic solar cells (OSCs) using buffer and anode combined Ta doped $In_2O_3$ (ITaO) electrodes. To optimize the ITaO electrodes, we investigated the effect of $Ta_2O_5$ doping power on the electrical, optical, and structural properties of the co-sputtered ITaO films. The optimized ITaO film doped with 20 W $Ta_2O_5$ radio frequency power showed sheet resistance of 17.11 Ohm/square, a transmittance of 93.45%, and a work function of 4.9 eV, all of which are comparable to the value of conventional ITO electrodes. The conventional bulk heterojunction OSC with ITaO anode showed a power conversion efficiency (PCE) of 3.348% similar to the OSCs (3.541%) with an ITO anode. In addition, OSCs fabricated on an ITaO electrode successfully operated without an acidic PEDOT:PSS buffer layer and showed a PCE of 2.634%, which was much higher than the comparable no buffer OSC with an ITO anode. Therefore, co-sputtered ITaO electrodes simultaneously acting as a buffer and an anode layer can be considered promising transparent electrodes for cost-efficient and reliable OSCs because they can eliminate the use of an acidic PEDOT:PSS buffer layer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.473.1-473.1
• /
• 2014

We report on the characteristics of Zr-doped $In_2O_3$ (IZrO) films prepared by DC-RF magnetron cosputtering of $In_2O_3$ and $ZrO_2$ targets for use as a transparent electrode for high efficient organic solar cells (OSCs). The effect of $ZrO_2$ doping power on electrical, optical, structural, and surface morphology of the IZrO film was investigated in detail. At optimized $ZrO_2$ RF power of 50 W, the IZrO film exhibited a low sheet resistance of 20.71 Ohm/square, and a high optical transmittance of 83.9 %. Furthermore, the OSC with the IZrO anode showed a good cell-performance: fill factor of 61.71 %, short circuit current (Jsc) of $8.484mA/cm^2$, open circuit voltage (Voc) of 0.593 V, and power conversion efficiency (PCE) of 3.106 %. In particular, the overall OSC characteristics of the cell with the IZrO anode were comparable to those of the OSC with the conventional Sn-doped $In_2O_3$ (FF of 65.03 %, Jsc of $8.833mA/cm^2$, Voc of 0.608 V, PCE of 3.495 %), demonstrating that the IZrO anode is a promising alternative to ITO anode in OSCs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.773-776
• /
• 2002

Efficient organic white light-emitting diodes are fabricated by doping [bis(2-methyl-8-quinolinolato) (tripheny-siloxy)aluminium (III)] (SAlq), a blue-emitting layer, with a red fluorescent dye of 4-dicyanomethylene-2-methyl-6-{2-(2,3,6,7-tetrahydro-1H,5H-benzo[i,j]quinolizin-8-yl)vinyl}-4H-pyran (DCM2). The incomplete energy transfer from blue-emitting SAlq to red-emitting DCM2 enables to obtain a balanced white light-emission. A device with the structure of ITO/TPD (50 nm)/SAlq:DCM2 (30 nm, 0.5 %)/$Alq_3$ (20 nm)/LiF (0.5 nm)/AI shows emission peaks at 456 nm and 482 nm from SAlq and at 570 nm from DCM2. The white light-emitting device shows an external quantum efficiency of about 2.3 %, a luminous efficiency of about 2.4 lm/W, and the CIE chromaticity coordinates of (0.32, 0.37) at 100 cd/m^2. A maximum luminance of about 23,800 cd/m^2. is obtained at 15 V and the current density of 782 mA/cm^2.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1995년도 춘계학술발표회 초록집
• /
• pp.45-52
• /
• 1995

광 촉매로 널리 알려진 TiO$_2$의 광 분해 거동의 변화를 관찰하기 위하여 Nb$_2$O$_{5}$를 첨가하여 sol-gel 용법으로 제조한 후 DCA(dichloroacetic acid) 의 광분해 효율을 측정하였다. Sol-gel process 과정에서 첨가된 Nb$_2$O$_{5}$의 농도 및 열처리 온도변화에 따른 광분해 효율을 관찰한 결과, Nb$_2$O$_{5}$를 첨가한 후 40$0^{\circ}C$에서 한시간 동안 열처리 한 광 촉매의 광분해 효율이 가장 높게 나타났다. 또한 열처리 온도와 무관하게 Nb$_2$O$_{5}$의 양이 증가할수록 광분해 효율은 감소하는 것으로 관찰되었다. 이는 excess electron 의 증가로 환원 반응 혹은 recombination rate기 증가하기 때문이라고 사료된다. 분해 대상 물질의 pH가 낮을수록 광분해 효율이 증가하는 것을 알 수 있었다.알 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.431-431
• /
• 2011

Graphene, two dimensional sheet of sp2-hybridized carbon, has attracted an enormous amount of interest due to excellent electrical, chemical and mechanical properties for the application of transparent conducting films, clean energy devices, field-effect transistors, optoelectronic devices and chemical sensors. Especially, graphene is promising candidate to detect the gas molecules and biomolecules due to the large specific surface area and signal-to-noise ratios. Despite of importance to the disease diagnosis, there are a few reports to demonstrate the graphene- and rGO-FET for biological sensors and the sensing mechanism are not fully understood. Here we describe scalable and facile fabrication of rGO-FET with the capability of label-free, ultrasensitive electrical detection of a cancer biomarker, prostate specific antigen/${\alpha}1$-antichymotrypsin (PSA-ACT) complex, in which the ultrathin rGO sensing channel was simply formed by a uniform self-assembly of two-dimensional rGO nanosheets on aminated pattern generated by inkjet printing. Sensing characteristics of rGO-FET immunosensor showed the highly precise, reliable, and linear shift in the Dirac point with the analyte concentration of PSA-ACT complex and extremely low detection limit as low as 1 fg/ml. We further analyzed the charge doping mechanism, which is the change in the charge carrier in the rGO channel varying by the concentration of biomolecules. Amenability of solution-based scalable fabrication and extremely high performance may enable rGO-FET device as a versatile multiplexed diagnostic biosensor for disease biomarkers.

• Journal of Radiation Protection and Research
• /
• 제28권2호
• /
• pp.87-95
• /
• 2003

반도체 검출기의 p+ 층의 도핑 농도, 열처리에 의한 불순물 재분포와 절단면에서의 guard ring 효과를 전산모사하여 최적의 구조와 공전을 설계하고, MCNP코드로 방사선 반응 특성을 분석하였다. 검출기는 반도체 집적회로 공정에서 설계된 공정변수를 적용하여 격자 방향 <100>, $400{\Omega}cm$, n형, Floating-Zone 실리콘 기판에서 제작되었다. 제작된 검출기의 누설전류 밀도는 $0.7nA/cm^2/100{\mu}m$로서 전기적 특성이 우수한 것으로 나타났으며, Cs-137 감마 선원에 의한 $5mR/h{\sim}25R/h$의 조사선량률 범위에서 방사선 반응 특성은 양호한 선형성을 보였다. 본 연구에서 제안된 공정으로 제작된 PIN 반도체 검출기는 개인선량 측정에 사용될 수 있을 것이다.

• Journal of Information Display
• /
• 제4권2호
• /
• pp.13-18
• /
• 2003

We synthesized bis (2-methyl-8-quinolinolato)(triphenylsiloxy) aluminum (III) (SAlq), a blue-emitting material having a high luminous efficiency, through a homogeneous-phase reaction. The photoluminescence (PL) and electroluminescence (EL) spectra of SAlq show two peaks at 454 nm and 477 nm. Efficient white light-emitting devices are fabricated by doping SAlq with a red fluorescent dye of 4-dicyanomethylene-2-methyl-6-{2-(2,3,6,7-tetrahydro-1H,5H-benzo[i,j]quinolizin-8yl) vinyl}-4H-pyran (DCM2). The incomplete energy transfer from blue-emitting SAlq to red-emitting DCM2 results in light-emission of both blue and orange colors. Devices with the structure of ITO/TPD (50 nm)/SAlq:DCM2 (30 nm, 0.5 %)/$Alq_3$ (20 nm)/LiF (0.5 nmj/Al show EL peaks at 456 nm and 482 nm originating from SAlq and at 570 nm from DCM2, resulting in the Commission Internationale d'Eclairage (CIE) chromaticity coordinates of (0.32, 0.37). The device exhibits an external quantum efficiency of about 2.3 % and a luminous efficiency of about 2.41m/W at 100 $cd/m^2$. A maximum luminance of about 23,800 $cd/m^2$ is obtained at the bias voltage of 15 V.

• 한국세라믹학회지
• /
• 제47권5호
• /
• pp.457-460
• /
• 2010

$SmCoO_3$ system was investigated for their application to themoelectric materials. All specimens showed p-type semiconducting behavior and their electrical conductivity ($\sigma$), Seebeck coefficient (S) and power factor were measured at high temperature. And the effect of dopant ions on their thermoelectrical properties were also investigated. $Fe^{3+}$ ion doped into $Co^{3+}$ site enhanced the Seebeck coefficient and decreased the electrical conductivity simultaneously. The maximum Seebeck coefficient value for 60% doping case reached to 780 ${\mu}V$/K at $240^{\circ}C$. However $Fe^{3+}$ doped system cause an negative effect on power factor value. In case of the pure phase, the maximum Seebeck coefficient value reached to 290 ${\mu}V$/K at $240^{\circ}C$ and the maximum electrical conductivity was obtained 748 1/(ohm$\times$cm) at $960^{\circ}C$. As a result, the maximum power factor was obtained $1.49\times10^{-4}$ W/$mK^2$ at $550^{\circ}C$.

• 한국재료학회지
• /
• 제31권9호
• /
• pp.502-510
• /
• 2021

Hierarchically porous carbon materials with high nitrogen functionalities are extensively studied as high-performance supercapacitor electrode materials. In this study, nitrogen-doped porous carbon textile (N-PCT) with hierarchical pore structures is prepared as an electrode material for supercapacitors from a waste cotton T-shirt (WCT). Porous carbon textile (PCT) is first prepared from WCT by two-step heat treatment of stabilization and carbonization. The PCT is then nitrogen-doped with urea at various concentrations. The obtained N-PCT is found to have multi-modal pore structures with a high specific surface area of 1,299 m² g^-1 and large total pore volume of 1.01 cm³ g^-1. The N-PCT-based electrode shows excellent electrochemical performance in a 3-electrode system, such as a specific capacitance of 235 F g^-1 at 1 A g^-1, excellent cycling stability of 100 % at 5 A g^-1 after 1,000 cycles, and a power density of 2,500 W kg^-1 at an energy density of 3.593 Wh kg^-1. Thus, the prepared N-PCT can be used as an electrode material for supercapacitors.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2019년도 전력전자학술대회
• /
• pp.230-232
• /
• 2019

Light Triggerd Thyristor (LTT)는 HVDC 및 산업용 스위치 등에 사용되는 대전력 반도체소자이다. 일반적인 Thyristor가 전기적 신호에 의해 trigger 되는 것과는 다르게 LTT는 광신호에 의해 동작하는 소자이다. 본 논문에서는 5,000V, 2,200A 급의 4인치 LTT 소자의 제작 및 전기적인 특성평가 결과를 기술하였다. 4인치 LTT의 구조적인 특징은 전면부 중앙에 광신호가 주입되는 수광부가 위치해 있으며 입력 전류 증폭을 위한 4-단계 증폭 게이트 (gate) 구조를 가지도록 설계하였다. $400{\Omega}{\cdot}cm$ 비저항을 갖는 1mm 두께의 n-형 실리콘 웨이퍼에 boron 이온주입과 열처리 공정으로 약 $30{\mu}m$ 깊이의 p-base를 형성하였으며, 고내압 저지를 위한 edge termination은 VLD (variable lateral doping) 기술을 적용하였다. 제작된 4인치 LTT는 6,500 V의 순방향 항복전압 ($V_{DRM}$) 특성을 나타내었으며, 100V의 어노드전압 ($V_A$)과 20 mA의 게이트전류 ($I_G$)에 의하여 thyristor가 trigger 됨을 확인하였다. 제작한 LTT 소자는 disk형 press-pack 패키지를 진행한 후, LTT의 수광부에 $10{\mu}s$, 50 mW의 900 nm 광 펄스를 조사하여 전류 특성을 평가하였다. LTT 패키지 샘플에 60 Hz 주파수의 광 펄스를 조사한 경우 2,460 A의 순방향 평균전류 ($I_T$)와 $336A/{\mu}s$의 반복전류상승기울기 (repetitive di/dt)에 안정적으로 동작함을 확인하였다. 또한, 펄스 전류 시험의 경우 61.6 kA의 최대 통전 전류 (ITSM, surge current)와 $1,050A/{\mu}s$의 펄스전류 상승 기울기 (di/dt of on-state pulse current)에도 LTT의 손상 없이 동작함을 확인하였다.