• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1351_1352
• /
• 2009

We deposited $SnO_2$:F thin films by atomospheric pressure chemical vapor deposition(APCVD) on corning glass. $SnO_2$:F films were used as transparent conductive oxide (TCO) electrode for Si thin film solar cells. We have investigated structural, electrical and optical properties of $SnO_2$:F thin films and fabricated thin film Si solar cells by plasma enhanced CVD(PECVD) on $SnO_2$:F thin films The cells were characterized by I-V measurement using AM1.5 spectra. Conversion efficiency of our cells were between 5.61% and 6.45%.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.291-297
• /
• 1999

The plasma etching of tungsten thin films has been studied with $SF_6$ gas in RIE system. The etch rate of ${\alpha}$-phase W film with $SF_6$ gas plasma has been showed to depend strongly on process parameters ($SF_6$, $SF_6-N_2$ gas). Effect of $N_2$ addition and etching selectivity between W film and photoresist have also been studied in detail. Etching profiles between W film and photoresist were investigated by SEM. The compounds on W surface after $SF_6-N_2$ gas plasma treatment were examined by XPS and the concentration of F ions was detected by OES during plasma on.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.341-346
• /
• 2010

In this paper, anti-reflection coating was investigated for decreasing the reflection in visible range of 400~650 [nm] through four staked layers of $Si_xO_y$ and $Si_xN_y$ thin films prepared by reactive sputtering method. Si single crystal of 6 [inch] diameter was used as a sputtering target. Ar and $O_2$ gases were used as sputtering gases for reactive sputtering for the $Si_xO_y$ thin film, and Ar and $N_2$ gases were used for reactive sputtering for the $Si_xN_y$ thin film. DC pulse power of 1900 [W] was used for the reactive sputtering. Refractive index and deposition rate were 1.50 and 2.3 [nm/sec] for the $Si_xO_y$, and 1.94 and 1.8 [nm/sec] for the $Si_xN_y$ thin film, respectively. Considering the simulation of the four layer anti-reflection coating structure with the above mentioned films, the $Si_xO_y-Si_xN_y$ stacked four-layer structure was prepared. The reflection measurement result for that structure showed that a "W" shaped anti-reflection was obtained successfully with a reflection of 1.7 [%] at 550 [nm] region and a reflection of 1 [%] at 400~650 [nm] range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.471-474
• /
• 2000

A flat type microgas sensor was fabricated on the p-type silicon wafer with low stress S $i_3$ $N_4$, whose thickness is 2${\mu}{\textrm}{m}$ using MEMS technology and its characteristics were investigated. W $O_3$thin film as a sensing material for detection of N $O_2$gas was deposited using a tungsten target by sputtering method, followed by thermal oxidation at several temperatures (40$0^{\circ}C$~$600^{\circ}C$) for one hour. N $O_2$gas sensitivities were investigated for the W $O_3$thin films with different annealing temperatures. The highest sensitivity when operating at 20$0^{\circ}C$ was obtained for the samples annealed at $600^{\circ}C$. As the results of XRD analysis, the annealed samples had polycrystalline phase mixed with triclinic and orthorhombic structures. The sample exhibit higher sensitivity when the system has less triclinic structure. The sensitivities, $R_{gas}$ $R_{air}$ operating at 20$0^{\circ}C$ to 5 ppm N $O_2$of the sample annealed at $600^{\circ}C$ were approximately 90. 90.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.173-176
• /
• 1997

The III-V nitride semiconductor InN thin films which have the direct bandgap in visible light wavelength region have been deposited on Si(100) substrates and AIN/Si(100) substrates by rf reactive sputtering. InN thin films have been investigated on the structural, and electrical properties according to the sputtering parameters such as total pressure, rf power, and substrate temperature. It is found that optimal conditions required for fabricating InN thin films with high crystal Quality, low carrier concentration, high Hall mobility are total pressure 5mTorr, rf power 60W, substrate temperature 6$0^{\circ}C$ . InN thin films deposited on the AIN(60min.)/Si(100) substrates arid AIN(120min.)/Si(100) substrates showed remarkably high crystal quality and electrical properties. It is known that AIN buffer layer is to decrease free energy at interface between InN film and Si substrate, and then promoting lateral growth of InN films.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1333-1334
• /
• 2007

Al thin film was the most popular electrode in semiconductor and flat panel display world, because of its electrical conductivity, selectivity and easy to apply to thin film. However, Al thin films were not good to use on the bottom electrode about the crystalline growth of inorganic compound materials such as ZnO, AlN and GaN, because of its surface roughness and melting points. In this paper, we investigated Ar plasma surface treatment of Al thin film to enhance the surface roughness and electrical conductivity using the reactive ion etching system. Several process conditions such as RF power, working pressure and process time were controlled. In results, the surface roughness showed $15.53\;{\AA}$ when RF power was 100 W, working pressure was 50 mTorr and process time was 10 min. Also, we tried to deposit ZnO thin films on the each Al thin films, the upper conditions showed the best crystalline characteristics by x-ray diffraction.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.2
• /
• pp.47-51
• /
• 2007

F-doped SiOC : H thin films with low refractive index were deposited on Si wafer and glass substrate by plasma enhanced chemical vapor deposition (PECVD) as a function of rf powers, substrate temperatures, gas rates and their composition flow ratios ($SiH_4,\;CF_4$ and $N_2O$). The refractive index of the F-doped SiOC : H film continuously decreased with increasing deposition temperature and rf power. As $N_2O$ gas flow rate decreased, the refractive index of the deposited films decreased down to 1.3778, reaching a minimum value at rf power of 180W and $100^{\circ}C$ without $N_2O$ gas. The fluorine content of F-doped SiOC : H film increased from 1.9 at% to 2.4 at% as the rf power was increased from 60 W to 180 W, which results in the decrease of refractive index.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.2
• /
• pp.250-254
• /
• 2003

A film bulk acoustic resonator (FBAR) device for 2 GHz radio frequency (RF) bandpass filter application is presented. This FBAR device consists of an aluminum nitride (AlN) film sandwiched between top(Al) and bottom(Au) electrodes and an acoustic multilayer reflector of a silicon dioxide/tungsten (SiO2/W). The A/N film deposited using a RF sputtering was observed to have small columnar grains with a strongly preferred orientation towards c axis. In addition to a high quality factor (4300), a large return loss of 37.19 dB was obtained.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.18-28
• /
• 1994

Sliding friction between a spherical pin of 8mm in diameter and flat (disk) substrates coated with vacuum-deposited thin film was measured under ultra high vacuum pressure for various materials, various rates of film supply (8~210 nm/min), various sliding velocities (1.5~67.0 mm/s). It was found that the most effective lubrication was obtained when the adhesion between $Si_3N_4$ pin and SUS440C disk was high and that between $Si_3N_4$ pin and $Si_3N_4$ disk was low. When In film was used as a lubricant between $Si_3N_4$ pin and stainless steel disk, the friction coefficient had a value as low as 0.04. In this case, the normal load W and the sliding speed V were expressed as 10N and 24 mm/s for $10^{-6}Pa$. The dependence of $\mu$ on the thickness h of the Ag film, which was used as a lubricant between $Si_3N_4$ pin and SUS440C (Q) disk was expressed as $\mu$=0.12 for W=10N and V=24mm/s when the film was thicker than 100nm. A brief discussion on these relations is presented from the viewpoint of the real contact area.

• 한국초전도학회:학술대회논문집
• /
• 2007.07a
• /
• pp.34-34
• /
• 2007