• 마이크로전자및패키징학회지
• /
• 제28권3호
• /
• pp.33-38
• /
• 2021

최근 유연 디스플레이에 관한 대중의 관심이 증대됨에 따라 롤러블(rollable), 폴더블(foldable) 디스플레이와 같은 우수한 폼 팩터(form factor)를 지닌 차세대 유연(flexible) 디스플레이가 주목받고 있다. 유연 디스플레이의 기계적 신뢰성 확보 측면에서, 내부 절연막으로 활용되는 실리콘 질화물(SiN_x) 박막은 구동 중 발생하는 응력에 매우 취약하므로 기계적 물성을 정확히 파악하여 파손을 예측하고 패널의 전기적 단락을 방지하는 것이 중요하다. 본 논문에서는, ~130 nm, ~320 nm 두께의 SiN_x 박막 박막 상부에 ~190 nm 두께의 유기 나노 보강층(PMMA, PS, P3HT)을 코팅하여 이중층 구조로 인장함으로써 매우 취성한 SiN_x 박막의 탄성 계수와 인장 강도 및 연신율을 측정하는 데 성공하였다. 챔버 압력 및 증착 파워를 조절한 공정 조건(A: 1250 mTorr, 450 W/B: 1000 mTorr, 600 W/C: 750 mTorr, 700 W)을 통해 제작된 ~130 nm SiN_x 의 탄성계수는 A: 76.6±3.5, B: 85.8±4.6, C: 117.4±6.5 GPa로, ~320 nm SiN_x는 A: 100.1±12.9, B: 117.9±9.7, C: 159.6 GPa로 측정되었다. 결과적으로, 동일 공정 조건 하에서 SiN_x 박막의 두께가 증가할수록 탄성 계수가 증가하는 경향을 확인하였으며, 유기 나노 보강층을 활용한 인장 시험법은 파손되기 쉬운 취성 박막의 기계적 물성을 높은 정밀도로 측정하는 데 효과적이었다. 본 연구에서 개발된 방법은, 취약한 디스플레이용 박막의 정량적인 기계적 물성 파악을 가능케하여 강건한 롤러블, 폴더블 디스플레이의 설계에 이바지할 수 있을 것으로 기대한다.

• 센서학회지
• /
• 제14권2호
• /
• pp.131-135
• /
• 2005

This paper describes the ohmic contact formation of single crystalline 3C-SiC thin films heteroepitaxially grown on Si(001) wafers. In this work, a TiW (Titanium-tungsten) film as a contact matieral was deposited by RF magnetron sputter and annealed with the vacuum and RTA (rapid thermal anneal) process respectively. Contact resistivities between the TiW film and the n-type 3C-SiC substrate were measured by the C-TLM (circular transmission line model) method. The contact phases and interface the TiW/3C-SiC were evaulated with XRD (X-ray diffraction), SEM (scanning electron microscope) and AES (Auger electron spectroscopy) depth-profiles, respectively. The TiW film annealed at $1000^{\circ}C$ for 45 sec with the RTA play am important role in formation of ohmic contact with the 3C-SiC substrate and the contact resistance is less than $4.62{\times}10^{-4}{\Omega}{\cdot}cm^{2}$. Moreover, the inter-diffusion at TiW/3C-SiC interface was not generated during before and after annealing, and kept stable state. Therefore, the ohmic contact formation technology of single crystalline 3C-SiC using the TiW film is very suitable for high temperature MEMS applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.62-65
• /
• 1997

Indium nitride thin films were deposited on Si(100) substrates by reactive sputtering method. The metallic indium target was sputtered by nitrogen gas with rf sputtering equipment. The surface morphology and cross-section of the InN thin films were investigated by scanning electron microscopy. The crystal orientations were investigated by X-ray diffraction and the Hall effect were measured with van der Pauw method. The indium nitride thin film showed high Hall mobility(215$\textrm{cm}^2$/V-sec) at 5mTorr total pressure and rf power 60W.

• 전기학회논문지
• /
• 제65권4호
• /
• pp.611-616
• /
• 2016

In this study, we synthesized $Ag_2Se$ nanoparticles (NPs) in an aqueous solution and investigated the thermoelectric characteristics of $Ag_2Se$ NPs thin films on plastic substrates. Regardless of thermal annealing treatment, all the $Ag_2Se$ NPs thin films show the negative Seebeck coefficients, indicating the n-type characteristics. As the annealing temperature increases, the electric conductivity increases while the Seebeck coefficient decreases. The electric conductivity of the thin film annealed at $180^{\circ}C$ is larger by $10^6$ times, compared with the as-prepared thin film, And the maximum power density for the thin film annealed at $180^{\circ}C$ is calculated to be $44{\mu}W/cm^2$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.718-721
• /
• 2004

The $(Sr_{0.9}Ca_{0.1})TiO_3$(SCT) thin films are deposited on Pt-coated electrode$(Pt/TiN/SiO_2/Si)$ using RF sputtering method at various substrate temperature. The optimum conditions of RF power and $Ar/O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about $18.75[{\AA}/min]$. The crystallinity of SCT thin films were increased with increase of substrate temperature in the temperature range of $100\sim500[^{\circ}C]$. The dielectric constant of SCT thin films were increased with the increase of substrate temperature, and changed almost linearly in temperature ranges of $-80\sim+190[^{\circ}C]$. The current-voltage characteristics of SCT thin films showed the increasing leakage current as the substrate temperature increases.

• 한국표면공학회지
• /
• 제29권1호
• /
• pp.3-14
• /
• 1996

High temperature anneal of W-rich silicides, inferior to adherence compared with Si-rich silicides, resulted in the film peeling off from the Si-substrate when WSix thickness reached more than critical thickness. Investigation of the W-rich silicide films peeling off from the substrate revealed that the voids underneath the $WSi_2$ produced through silicide reaction were responsible for the poor adherence of W-rich silicide. In addition, internal stress in the film increased as the silicide thickness increased. In order to promote the adhesion of WSix to Si-substrate, thin Ti-layer was formed between WSi and Si-substrate(WSix/Ti/Si). No voids were observed in $WSi_2$/Ti/Si $N_2$-annealed at $1000^{\circ}C$, thereby leading to an increase of the critical thickness from ～1700$\AA$ to more than 2500$\AA$. However, higher resisiti-vity was obtained in WSix/Ti/Si than in WSix/Si. Finally, different silicide reaction mechanism for the structures(WSix/Si, WSix/Ti/Si) was proposed to explain the formation of voids as well as the role of thin Ti-layer.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2006년도 High Temperature Superconductivity Vol.XVI
• /
• pp.32-32
• /
• 2006

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.358-361
• /
• 1999

This paper describes on the fabrication and characteristics of hot-film type micro-flowsensors integrated with Pt-RTD\`s and micro-heater on the Si substrate, in which MgO thin-films were used as medium layer in order to improve adhesion of Pt thin-films to SiO$_2$ layer The MgO layer improved adhesion of Pt thin-films to SiO$_2$` layer without any chemical reactions to Pt thin-films under high as gas flow rate and its conductivity increased due to increase of heat-loss from sensor to external. Output voltage was 82 mV at N2 flow rate of 2000 sccm/min, heating power of 1.2W. The respons time was about 100 msec when input flow was step-input

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권9호
• /
• pp.397-402
• /
• 2005

The ($Sr_{1-x}Ca_x)TiO_3(SCT)$ thin films are deposited on Pt-coated electrode (Pt/TiN/SiO$_{2}$Si) using RF sputtering method with substitutional contents of Ca. The optimum conditions of RF power and Ar/O$_{2}$ ratio were 140(W) and 80/20, respectively. Deposition rate of SCT thin film was about $18.75{\AA}$/min. The dielectric constant was increased with increasing the substitutional contents of Ca, while it was decreased if the substitutional contents of Ca exceeded over $15[mol\%]$. The capacitance characteristics had a stable value within $\pm4[\%]$ in temperature ranges of $-80\~+90[^{\circ}C]$. All SCT thin films used in this study show the phenomena of dielectric relaxation with the increase of frequency, and the relaxation frequency is observed above 200[kHz].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.88-91
• /
• 2000

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films are deposited on Pt-coated electrode(Pt/TiN/$SiO_2$/Si) using RF sputtering method. The crystallinity of SCT thin films is increased with increase of substrate temperature in the temperature range of 200~500$[^{\circ}C]$. V-I characteristics of SCT thin films show the increasing leakage current with the increases of deposition temperature. The conduction mechanism of the SCT thin films observed in the temperature range of 25~100$[^{\circ}C]$ can be divided into four characteristic regions with different mechanism by the increasing current.