• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.261-264
• /
• 2003

In this paper, a disk-type piezoelectric transformer for the high power was investigated with the variation of road resistance. The diameter and thickness of a disk-type piezoelectric transformer was 45mm and 4mm, respectively. The piezoelectric ceramics was composed to PZT-PMN-PSN. The ratio of driving electrode and generating electrode is 2:1. The poling direction of driving part and generating part are the same. A voltage step-up ratio increased with increasing the load resistance, $R_L$, so it reached 60 under no road resistance. Also, the maximum efficiency of 97% was obtained.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.18-21
• /
• 2020

Undetected wafer slip during the lift pin-down motion in semiconductor equipment may affect the center to edge variation, wafer warpage, and pattern misalignment in plasma equipment. Direct measuring of the amount of wafer slip inside the plasma process chamber is not feasible because of the hardware space limitation inside the plasma chamber. In this paper, we demonstrated a practice for the wafer lift pin-up and down motions with respect to the gear ratio, operating voltage, and pulse width modulation to maintain accurate wafer position using remote control linear servo motor with an experimentally designed chamber mockup. We noticed that the pin moving velocity and gear ratio are the most influencing parameters to be control, and the step-wised position control algorithm showed the most suitable for the reduction of wafer slip.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.360-369
• /
• 2008

The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.25-26
• /
• 2011

In some cases of grid connected system using photovoltaic modules, high voltage step up ratio is required. In this paper, non-isolated 2-stage cascaded boost converter with coupled inductor is proposed. Due to reduce the input current ripple and size of the inductor by using coupled inductor method, this topology is suitable for MIC(Module Integrated Converter). The operational characteristic of the proposed topology is verified through the theorical analysis, simulation and experimental waveform.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1578-1588
• /
• 2015

In this paper, an improved KY converter is presented, which is constructed mainly by one charge pump capacitor and one central-tapped coupling inductor. Besides, a passive clamping snubber is added to this converter to improve the efficiency above half load. As compared to the KY converter, the voltage conversion ratio of the proposed converter is upgraded significantly. In this paper, the basic operating principles and mathematical deductions of the proposed converter are described, along with some experimental results provided to demonstrate the feasibility and effectiveness of the proposed converter.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.196-197
• /
• 2006

In this study, low temperature sintering multilayer piezoelectric transformer for DC-DC converter were manufactured using (PbCaSr)Ti(MnSb)$O_3$ ceramics and thin their electrical properties were investigated according to the vanation of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value m the vicinity of 1.3MHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the piezoelectric transformer showed the temperature rise of about $21^{\circ}C$ under the output power of 6W.

• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.761-767
• /
• 1993

Electrical and mechanical properties of Pb(Mg, Te, Mn, Nb)O3-PZT ceramics are investigated as a function of CeO2 addition (0 to 0.3wt%), and the output characteristics of piezoelectric transformer are also presented. The grain size decreased and the shapes of particles were more uniform with the addition of CeO2. The coercive electric field(9500V/cm), mechanical quality factor (2500) and bend strength (1065kg/$\textrm{cm}^2$) were improved by addition of CeO2 0.2wt%. After repetition of a number of stress cycles, the degradation of k33 was not found in this sample. The voltage step-up ratio (Vdc/Vrms) of piezoelectric ceramic transformer (half wavevoltage doubler, load resistor 100M.ohm) was about 950 in a linear region, its value was relatively higher than other materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.234-235
• /
• 2005

This paper present a new disk-type piezoelectric transformer. The input side of the transformer has a crescent-shaped electrode and the output side has a focused poling direction. The piezoelectric transformers operated in each transformer's resonance vibration mode. The electrodes and poling directions on commercially available piezoelectric ceramic disks were designed so that the planar or shear mode coupling factor ($k_p,\;k_{15}$) becomes effective rather than the transverse mode coupling factor ($k_{31}$).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.296-299
• /
• 2002

In this paper, a hexagon-type piezoelectric transformer was investigated to increase the output power. The length of its side was 14mm and 17.5mm, respectively. The piezoelectric ceramics was composed to PZT-PMN-PSN. This composition showed the characteristics which had an about 1500 of the mechanical Q-factor, 0.55 of the electromechanical coupling coefficient, $320{\times}10^{-12}C/N$ of the piezoelectric constant $d_{31}$, 0.3 % of the dissipation factor, etc. The voltage step-up ratio increased with increasing the load resistance, $R_{L}$, so it reached 80 with $R_{L}$ of $1M{\Omega}$ and was proportion to the length of side of the hexagon-type piezoelectric transformer. Also, the output power increased with increasing the size of the hexagon-type piezoelectric transformer.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1064_1065
• /
• 2009

PV (Photovoltaic) power generation system has been widely studied as a clean and renewable power source. Tracking the MPP (maximum power point) of a PV array is usually an essential part of a PV system. This paper describes POS (Photovoltaic Output Sensorless) MPPT method and optimization technique of its operational characteristics for grid-connected PV generation system. A DC-DC converter has been used to step-up the PV voltage and DC-AC converter has been used for connecting the system to the grid. Optimization technique has been implemented to optimize the current and voltage controller gain parameters and duty ratio increment of DC-DC converter. Simulation results reveal that the proposed control has better response.