• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.20-27
• /
• 2007

In this paper, finite element modeling was performed for vibration analysis of a rotor system installed in sunroof motor, and analysis process was developed for natural frequency and unbalance response analysis. At the same time, to reduce analysis modeling error caused by the difference between analysis and measured values, finite element model updating was conducted using an optimization algorithm, i.e. hybrid genetic algorithm and simulated annealing (HGASA) method. For this end experimental modal test was carried out and by using the measured frequency response function (FRF), model updating was performed considering both cases where core coil was removed and included. And acceptable result was obtained. Also, dynamic property coefficient of bush bearing which influences vibration response of the rotor system was estimated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1224-1230
• /
• 2007

In this study, a new modal test method is presented to evaluate vibration characteristic of the nano imprint stage system. Since it is difficult to measure vibration level without contacting the machine component, non contacting modal test method, laser scanning system is ultrared. Finite element analysis results are compared with the modal test results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.208-211
• /
• 2005

This paper describes the development process of steering system for reduce idle vibration through the data level of frequency and sensitivity. High stiffness and light weight vehicle is a major target in the refinement of passenger cars to meet customers' contradictable requirements between NVH performance and fuel economy. The target frequency of the steering system is set by benchmarking of a competitive vehicle and the vibration mode map is used to separate steering column modes from resonance of body structure and engine idle rpm. This paper descirbes the analysis approach process for high stiffness of steering system and the design guideline is suggested about steering column and support system by using mother car at initial design stage. We used a patent map in order to analyze accurately a technical trend and suggested the design process using dynamic damper of steering system considering sensitivity. And we established techniques of analysis on steering system and evaluated the level of accuracy of analysis through correlating the test and analysis results. It makes possible to design the good NVH performance vehicle at initial design stage and save vehicles to be used in tests. These improvements can lead to shortening the time needed to develop better vehicles.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.48-57
• /
• 1997

A computer aided analysis and design system is developed for analyzing the driveline torsional vibration of a vehicle. Torsional vibration characteristics of driveline component are investigated and 10 types of module are developed. They can be connected together to represent any driveline configuration. During assembly process simulation program is generated. It is implemented using C++language. A driveline tor- sional vibration system at full load driving condition and idle rattle system are modeled and simulated with this system. Their responses for engine torque excitation are evaluated on time and frequency domain, and the results are compared with test results favorably. This system makes it simpler and easier for design and analysis engineer to model and analyse the driveline system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.138-144
• /
• 2010

If the vibration is occurred in a large-sized bus roof, it makes people annoying and complaining the quality of a large-sized bus. So in design stage, it must be considered. To assess vibration at the roof which is equipped with air conditioner in design stage, finite element model is constructed. Computer simulation analysis and experimental method are performed. The dynamic characteristics of the large-sized bus are found by using eigenvalue method. It is related with dynamic behavior. The running conditions of a large-sized bus are velocity and road condition which followed experimental conditions. And the frequency response of a large-sized bus is well correlated with analysis result. Modal participation method is used for finding major modes at each peak. Using this method, we found that front and rear suspension system, engine mounting system and roof structure are the major reasons of the roof vibration. To reduce vibration level of roof in a large-sized bus, spring stiffness of front and rear suspension system, spring stiffness of engine mounting system and roof structure are properly combined. From this study, the vibration characteristics of the roof structure of a large-sized bus can be to a satisfactory level.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.618-623
• /
• 2001

In a practical vibration isolation system, vibration is transmitted from the source to the receiver through several paths such as more than one inter-connected point and multi-degree of freedom at each connection point. Therefore, the major path investigation for vibration transmission among them is often required in a point of view of isolation. For the path analysis of multi-dimensional vibration isolation system, it is useful to employ the concept of vibration power in high frequency range where radiation of noise from the receiver structure is concerned. The idea is simple to understand and formulate but rather complicated to apply in practice. For an accurate estimation of power flow especially over a high frequency range, it is well known in theory that rotational motions should be taken into consideration together with translational motions at inter-connected points. In reality, however, power transmissions related to rotational terms are often neglected mainly due to difficulties in the instrumentation. In this paper, necessary formula and measurable mechanical quantities for vibration power analysis will be reviewed and experimental results with rotational terms included for compressor system in a commercial air conditioner will be shown.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.1070-1072
• /
• 2003

In this paper, Firstly, it is shown that the high vibration source of piping system is the pulsation transmission of pipe line element ,such as, orifice plate, valves and the control valve is a broad band source and the branch wall and the cavity have vortex frequency Secondly, in order to decrese the turbulence vibration of piping system, the practical analysis of piping flow by EFD have been developed and its effectiveness is investigated as applying it at piping system practically.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.155-160
• /
• 1996

The vibration analysis of the automobiles has been a good subject for the engineers seeking solutions for more comfortable life. In the area of industrial vehicles, however, the seriousness of the vibration annoyance has not been considered so much. In this paper, a finite element model was built which was good for the low-frequency system(of fork-lift truck), and a forced vibration analysis was obtained for the component of 2n of harmonic orders from engine excitation to this model. Finally, a design optimization upon dynamic responses was made to minimize the vibration acceleration level at selected points representing the vibration level of the whole system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.391-397
• /
• 2005

Power Flow Analysis(PFA) is used as the promising tools for the vibration and noise predictions of complex structures in medium-to-high frequency ranges. When the noise and vibration of a complex structure are analyzed, Power Flow finite Element Method combining PFA with FEM is efficient in vibration analysis, and Power Flow Boundary element Method combining PFA with BEM is usful in noise analysis. PFFEM software, PFADS has been developed for the vibration analysis of coupled system structures. Also, NASPFA, the noise analysis software based on PFBEM, has been developed. Through the several upgrades, the current version PFADS R3 and NASPFA R2 are used for the vibration and noise analysis of system structures in medium-to-high frequency ranges. In this paper, the structure and function of each software are explained, and the vibration and noise levels of vehicle structures predicted by each software are shown.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.3
• /
• pp.43-53
• /
• 2004

The vibration of a rolling piston type rotary compressor for air-conditioning use is analyzed numerically and experimentally. Multibody dynamic analysis methods to predict the vibration are given. The compressor is modeled as a multibody system composed of bodies, joints, and force elements. Experimental results are shown to compare with simulation results. A sensitivity study using different variables that affect the compressor vibration is also carried out. It is found that the mass of the weight balancer plays an important role in acceleration.