• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.973-978
• /
• 2010

In this paper, we studied the shimmy phenomena of an aircraft nose landing gear considering free-play. Shimmy is a self-excited vibration in lateral and torsional directions of a landing gear during either the take-off or landing. This phenomena is caused by a couple of conditions such as low torsional stiffness of the strut, friction and free-play in the gear, wheel imbalance, or worn parts, and it may make an aircraft unstable. Free-play non-linearity is linearized by the described function for a stability analysis in a frequency domain, and time marching is performed using the fourth-order Runge-Kutta method. We performed the numerical simulation of the nose landing gear shimmy and investigated its linear and nonlinear characteristics. From the numerical results, we found limit-cycle-oscillations at the speed under linear shimmy speed for the case considering free-play and it can be concluded that the shimmy stability can be decreased by free-play.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.145-148
• /
• 2007

In this paper a development if data acquisition system for machinery monitoring and its condition analysis is discussed A suitable data acquisition system should be adopted to get desirable monitoring results for ship's machinery. 1he compactness and moderate cost are also considered to compose the data acquisition system 1he basic components if data acquisition system for monitoring are introduced and automatic data saving function with variable time interval and remote monitoring system are also proposed An experiment to get vibration data for rotating machinery is executed to verify the effectiveness if the data acquisition system.

• Smart Structures and Systems
• /
• v.6 no.9
• /
• pp.1057-1077
• /
• 2010

An early detection of structural damages is critical for the decision making of repair and replacement maintenance in order to guarantee a specified structural reliability. Consequently, the structural damage detection, based on vibration data measured from the structural health monitoring (SHM) system, has received considerable attention recently. The traditional time-domain analysis techniques, such as the least square estimation (LSE) method and the extended Kalman filter (EKF) approach, require that all the external excitations (inputs) be available, which may not be the case for some SHM systems. Recently, these two approaches have been extended to cover the general case where some of the external excitations (inputs) are not measured, referred to as the adaptive LSE with unknown inputs (ALSE-UI) and the adaptive EKF with unknown inputs (AEKF-UI). Also, new analysis methods, referred to as the adaptive sequential non-linear least-square estimation with unknown inputs and unknown outputs (ASNLSE-UI-UO) and the adaptive quadratic sum-squares error with unknown inputs (AQSSE-UI), have been proposed for the damage tracking of structures when some of the acceleration responses are not measured and the external excitations are not available. In this paper, these newly proposed analysis methods will be compared in terms of accuracy, convergence and efficiency, for damage identification of structures based on experimental data obtained through a series of laboratory tests using a scaled 3-story building model with white noise excitations. The capability of the ALSE-UI, AEKF-UI, ASNLSE-UI-UO and AQSSE-UI approaches in tracking the structural damages will be demonstrated and compared.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.339-346
• /
• 2012

In this paper, equivalent models for active control devices are proposed so that building structures with such devices are analyzed using commercial structural analysis programs for the assessment of the structural members under active vibration control. Equivalent link models represent active control device with a virtual linear spring and dashpot, and equivalent force models are control force history acting at the installation point in structural models. Active controllers are designed based on the reduced-order models for a vertical cantilever model and a high-rise building model and corresponding equivalent models are determined from control gain matrices. Based on acceleration, displacement and member force responses, the effectiveness of the equivalent models is verified. As a result, proposed equivalent models, of which equivalent link model showed better performance, appear to enable detailed investigation of structural behavior to the extent of member force level.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.180-185
• /
• 2014

Due to the larger and high-speed vessels recently constructed, output and speed of the engines for propulsion or power generation is increasing. These high-power and high-speed engine of the ship is becoming as a major contributor causing excessive noise and vibration. Other fittings as well as equipment installed on board, it makes equipment failure or other defect by resonance. This causes a lot of M/H(Man Hour) for repairs and the reliability of the company is invading even be negative because the clients give much comment. Thus, it's being studied for any fittings installed on board to maintain the safe operation and to prevent any problem during the performance in any operating conditions. In this study, it was investigated to solve these problems for the supports of the various fittings for easy installation-related support that each type of intensity and shape and manufacturing method using structural analysis program(DNV Nauticus Hull 3D Beam). Namely, it would be applied to the very large crude carriers in consideration of mechanics of materials of the support equipment by providing the fact that dynamics analysis of the structural characteristics of the equipment and the support of the production installation is easy and productivity can be high standards for geometry and thereby to simplify the analysis task to design changes at the same time and to minimize the reinforcement for the supports.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.268-272
• /
• 2023

This study explores the characteristics of tilting pad journal bearings used in the high-speed rotating shaft systems of centrifugal compressors. A centrifugal compressor is a high-speed rotating machine that is widely used to compress gases or vapors employed in various industrial applications. It transfers the centrifugal force of a fast-spinning impeller to the fluid and compresses it under high pressure. Many high-speed rotating shaft systems, which require high stability, use tilting pad journal bearings. The characteristics of these bearings can vary depending on several properties, and identifying the appropriate characteristics is essential to optimize the design on a case-to-case basis. In this study, the authors perform a time-dependent analysis of the properties of tilting pad journal bearings and the rotordynamics of the rotating shaft system using COMSOL Multiphysics software. Specifically, the authors analyze the characteristics of the tilting pad journal bearings by performing a parametric sweep using parameters such as pad clearance, maximum tilting angle, preload, number of pads, and pad pivot offset. The authors then use the results of the bearing-characteristics analysis to evaluate the vibration of the rotating shaft and verify its operation within a desirable range. The understanding gained from this study will allow us to determine the optimal properties of these bearings and the limiting operational speed using COMSOL Multiphysics software.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.141-152
• /
• 2022

As interest increases related to the development of eco-friendly energy, the offshore wind turbine market is growing at an increasing rate every year. In line with this, the demand for an installation vessel with large scaled capacity is also increasing rapidly. The wind turbine installation vessel (WTIV) is a fixed penetration of the spudcan in the sea-bed to install the wind turbine. At this time, a review of the spudcan is an important issue regarding structural safety in the entire structure system. In the study, we analyzed the current procedure suggested by classification of societies and new procedures reflect the new loading scenarios based on reasonable operating conditions; which is also verified through FE-analysis. The current procedure shows that the maximum stress is less than the allowable criteria because it does not consider the effect of the sea-bed slope, the leg bending moment, and the spudcan shape. However, results of some load conditions as defined by the new procedure confirm that it is necessary to reinforce the structure to required levels under actual pre-load conditions. Therefore, the new procedure considers additional actual operating conditions and the possible problems were verified through detailed FE-analysis.

• The Journal of the Korea Contents Association
• /
• v.17 no.10
• /
• pp.376-384
• /
• 2017

Color therapy is a diagnostic method for treating psychological problems using unique vibration and frequency color. The color has strong subjective psychology, it can give psychological stabilization effect as a spring as a favorite color and stability become personally personal. Also, to give various influences on emotion, we can obtain information via brain wave to evaluate these emotions. In this research, before viewing two kinds of VR color images of red and blue, responding to the stress questionnaire(BEPSI-K) via a mobile terminal. At this time, we analyzed the real-time we used four emotional data measurable via brain waves and grasped the user's emotional state. In addition, the stress questionnaire was used to quantify the emotion degree, and comparative analysis was made on how the color image affects the change of emotions with 3D virtual reality.

• Structural Engineering and Mechanics
• /
• v.67 no.6
• /
• pp.643-658
• /
• 2018

In this paper, we introduce a new framework for running the finite element (FE) packages inside an online Loop together with MATLAB. Contrary to the Hardware-in-the-Loop techniques (HiL), in the proposed Software-in-the-Loop framework (SiL), the FE package represents a simulation platform replicating the real system which can be out of access due to several strategic reasons, e.g., costs and accessibility. Practically, SiL for sophisticated structural design and multi-physical simulations provides a platform for preliminary tests before prototyping and mass production. This feature may reduce the new product's costs significantly and may add several flexibilities in implementing different instruments with the goal of shortlisting the most cost-effective ones before moving to real-time experiments for the civil and mechanical systems. The proposed SiL interconnection is not limited to ABAQUS as long as the host FE package is capable of executing user-defined commands in FORTRAN language. The focal point of this research is on using the compiled FORTRAN subroutine as a messenger between ABAQUS/CAE kernel and MATLAB Engine. In order to show the generality of the proposed scheme, the limitations of the available SiL schemes in the literature are addressed in this paper. Additionally, all technical details for establishing the connection between FEM and MATLAB are provided for the interested reader. Finally, two numerical sub-problems are defined for offline and online post-processing, i.e., offline optimization and closed-loop system performance analysis in control theory.

• Journal of Korean Society of Disaster and Security
• /
• v.6 no.2
• /
• pp.23-30
• /
• 2013

A dynamic analysis of random vibration processes is concerned with the first excursion probability based on first passage time during some specified lifetime or duration of the excitation. This study is concerned with the estimation of first-passage probability for hazard fluctuate wind velocity in the major cities reflecting the recent meteorological with largest data samples (yearly 2003-2012). The basic wind speeds were standardized homogeneously to the surface roughness category C, and to 10m above the ground surface. In this paper, the hazard fluctuate wind velocities are treated as a time-independent (stationary) random process and Gaussian random processes. The first excursion probability were calculated from Poisson model based on the independent event of level crossing & two-state Markov model based on the envelopes of level crossing.