• 대한기계학회논문집A
• /
• 제40권6호
• /
• pp.595-602
• /
• 2016

자동차용 휠 베어링은 회전운동을 전달하고 차량의 무게를 지지해주는 중요한 부품이다. 최근 $CO_2$ 배출가스 저감과 연비 규제에 따라서 자동차 경량화 및 소형화 요구는 점점 증가하고 있고, 이에 부응하여 베어링의 수명 평가기술은 더욱 그 필요성이 증가하고 있다. 휠 베어링의 내구수명은 고려해야 할 인자들이 매우 다양하며 이들이 서로 복잡하게 연관되어 있으므로 수명을 예측하는 것이 쉽지 않다. 본 논문에서는 자동차용 휠 베어링의 수명에 영향을 끼치는 많은 인자들 중에서 작동하중과 회전속도를 변화시키면서 수명을 시험하였고, 이를 ISO 국제표준에서 제안하는 이론수명인 기본정격수명과 보정정격수명 결과와 비교하였다. 이들 수명을 비교한 결과, 기본정격수명과 보정정격수명 모두 시험수명과 차이가 존재하며, 기본정격수명 보다 보정정격수명이 시험수명을 상대적으로 잘 예측함을 알 수 있었다.

• 한국철도학회논문집
• /
• 제11권3호
• /
• pp.225-232
• /
• 2008

축간거리가 긴 트럭이나 굴절차량과 같이 차량이 길이가 길고 2량 이상 편성된 차량은 회전반경을 줄여 원활하게 곡선을 주행할 수 있도록 전 차륜 조향방식(AWS)을 적용한다. 굴절차량에 도입된 방법은 네덜란드 APTS사의 Phileas 차량이 유일하며 자동으로 운전하기 위한 제어방법에 대한 논문은 발표되었지만 수동으로 조향되어 운전되는 경우에 대한 알고리즘은 소개되거나 공개되어지지 않았다. 따라서 본 연구에서 네덜란드의 APTS사의 차량에 대한 수동운전시의 조향장치 특성을 분석하고 새로운 알고리즘을 제안하였다. 또한 개발된 알고리즘을 상용 동역학 프로그램인 ADAMS를 이용하여 적용성을 알아보았다.

• 대한토목학회논문집
• /
• 제26권3D호
• /
• pp.461-467
• /
• 2006

노면에 차량 검지센서를 설치하여 개별차량의 속도자료를 수집하는 경우, 일반적으로 일정거리가 이격되게 설치한 두 개 이상의 차량 검지센서간의 반응시간을 활용하여 차량의 속도를 산출하게 된다. 본 논문에서는 차로당 센서 1개만을 설치하여 개별차량의 속도 산출을 함에 있어, 기존 방법인 파형의 기울기를 이용하여 속도 추정하는 방법(Case 1)과 평균차량길이를 적용한 속도산출(Case2), 새로 고안한 방법인 단일 테이프스위치(Tape Switch) 센서를 수평형으로 설치하고 평균축거를 적용하여 속도 추정하는 방법(Case 3), 그리고 테이프스위치 센서를 사선형으로 설치하고 차량의 평균윤거(Mean of tread)를 적용하여 속도 추정하는 방법(Case 4)에 대한 속도 추정정확도를 평가하였다. 4가지 방식 각각에 대해 현장에서 센서를 설치하고 기준값과 속도추정 값을 비교 분석을 했으며, 평가지표로는 등가계수(Equality Coefficient), 절대오차백분율(MAPE)을 통하여 평가하였다. 평가결과는 Case1 > Case 4 > Case 2, 3 순으로 양호한 결과를 보이는 것으로 분석되었다.

• 자동차안전학회지
• /
• 제5권1호
• /
• pp.16-24
• /
• 2013

Some GM (General Motors) vehicles are using a GMLAN (General Motors Local Area Network) communication protocol for control and diagnostics. The airbag control module uses vehicle speed information from the GMLAN to record the vehicle speed as pre-crash information. In order to use the vehicle speed information for crash reconstruction purposes, it helps to be able to understand the accuracy of the data. The actual vehicle speed is not expected to be the same as the GMLAN indicated speed in some situations like a spin or if there is hard braking. This paper compares the actual vehicle speed and vehicle speed information during specific vehicle maneuvers. Actual vehicle speed is calculated from a GPS sensor, while GMLAN vehicle speed is calculated from transmission output sensor by the Engine control module (ECM). Vehicle maneuvers defined as Mode #1, Mode #2, Mode #3. The Mode #1 maneuver simulates wheel lock-up and skidding f by hard-braking at a specific speed. The Mode #2 maneuver simulates a 90degree turn using a J-turn maneuver at a specific speed. The Mode#3 maneuver simulates a 180 degree turn using a spin type of maneuver at a specific speed. The study then compares the GMLAN speed and GPS speed to see what speed difference exists between them. The results of this paper are applicable to GM vehicles only. This paper catalogs the performance and limitations of two vehicles as useful reference for crash reconstructions where there is a need to understand the speed indicated in the pre-crash section of the SDM data.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.75-80
• /
• 2011

In the area of wheel on rail vehicle, hunting stability which is generated by lateral motion is one of important characteristics for running safety. It might cause not only oscillation of vehicle but also derailment in an unstable area of the high speed. A Maglev vehicle is usually controlled the voltage to maintain the air gap between electromagnet and track. However, in Maglev system, an occurrence possibility of hunting motion could be high, because Maglev vehicle is not controlled directly lateral force between electromagnet and track in the curved guideway. In this paper, running safety is evaluated when Maglev vehicle run on guideway at high speed according to installment of damper between maglev vehicles and bogies, and to analyze the effect of it. Also, the parametric study is carried out for selecting effective lateral damper properties through the simulation. To accurately predict the running safety, 3d multibody dynamics models which are included air spring, guideway conditions and irregularities profile are used. With the results acquired, suggestions were made whether to adopt the damper and how to optimize the damping characteristics.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.225-231
• /
• 2016

A military vehicle is driven at different usage modes with the army application and servicing conditions. For practical durability validation, DT(Development Test) on a new military vehicle should be run up to the durability target kilometers on test courses in the specified proving ground. Driving velocities with test courses at the endurance mode of DT are established definitely. However, OT(Operational Test) and initial endurance test of production car can't be performed only in the DT courses due to the development period limit. Therefore, this paper focuses on the method to analyze the relative road damages between the endurance test in DT and other endurance test. Road load acquisition tests on KLTV(Korean Light Tactical Vehicle) were implemented at 15 driving modes in off-road and cross-country courses of two tests. Wheel accelerations were processed through band-pass filter, and then the main frequency and maximum power of the signals were computed by PSD analysis. Finally, using the proving ground optimization based on RDS(Relative Damage Spectrum) characterization, the damage factors between off-roads of test courses were determined.

• 전기학회논문지
• /
• 제59권3호
• /
• pp.645-650
• /
• 2010

In this paper we present the Bimodal-tram simulator using the PXI embedded real-time controllers. The Bimodal-tram is developed in KRRI (Korea Railroad Research Institute). The vehicle can be automatically operated by navigation control system (NCS). For the automatic driving, the vehicle lanes will be marked with permanent magnets that are placed in the ground. The vehicle is controlled by NCS. NCS governs the manual mode and automatic mode driving. The simulator is designed by an identical conception with the real control condition. The dynamic motion of vehicle is simulated by the nonlinear dynamic model. The control computer calculates the control values. The signal interface is linked by CAN communication. The simulation is processed by real-time base. The test driver can see the graphic motion of vehicle and can operate the steering wheel, gas and brake pedal to control direction and velocity of vehicle during the simulation. At present, the simulator is only operated by manual mode. The automatic mode will be linked after the control algorithm is finished. We will use the simulator to develop the control algorithm in the automatic mode. This paper shows the simulator designed for Bimodal-tram using real-time based controller. The results of the test using the simulator are presented and discussed.

• 전기학회논문지
• /
• 제60권10호
• /
• pp.1924-1934
• /
• 2011

This paper is concerned with the robustness evaluations of the guidance controller for a bimodal tram which is being developed by the Korea Railroad Research Institute (KRRI). The bimodal tram is an all-wheel steered multiple-articulated vehicle as a new kind of transportation vehicle. This vehicle has to be equipped with an automatic guidance system. In [1], such a controller has been recently proposed. However, since the performance is affected by weight change of the vehicle due to number of the passenger, model parameter uncertainties depending on the state of friction and the elasticity of the tire, and a typhoon, the controller designed must be examined with these conditions. As expected, because the vehicle dynamics is highly nonlinear, for the sake of investigating the robustness of the controller we compose two simulation ways based on the vehicle models which are implemented by the ADAMS and the MATLAB/LabVIEW toolboxes. Different uncertainties and a typhoon disturbance have been considered for the simulation conditions. Simulation results are shown.

• Structural Engineering and Mechanics
• /
• 제30권2호
• /
• pp.165-176
• /
• 2008

In this paper, a new iterative method for solving vehicle-bridge interaction problems is proposed. Iterative methods have advantages over the non-iterative methods in that it is not necessary to update the system matrix for a given wheel location, and the method can be applied for a new type of car or bridge with few or no modifications. In the proposed method, the necessity of system matrices update is eliminated using the equivalent interaction force acting on the bridge, which is obtained iteratively. Ballast stiffness is included in the interaction forces and the geometric compatibility at the contact points are used as convergence criteria. The bridge is considered as an elastic Bernoulli-Euler beam with surface irregularity and ballast stiffness. The moving vehicle is modeled as a multi-axle mass-spring-damper system having many degrees of freedom depending on the number of axles. The pitching effect, which is the interaction effect between the rear and front wheels when a vehicle begins to enter or leave the bridge, is also considered in the formulation including extended ground boundaries having surface irregularity and ballast stiffness. The applicability of the proposed method is illustrated in the numerical studies.

• 한국정밀공학회지
• /
• 제25권4호
• /
• pp.108-117
• /
• 2008

A transmission designed with P.T.O(Power Take-Off) axle for agricultural work vehicles including multi-purpose vehicles has been developed. It is focused on the 4-wheel drive transmission of synchronous contact type for practical use in fruit tree households which is required for a large-sized agricultural vehicle. Concerning to the specification performed, the load capacity is from 500kg to 1,000kg and the safety should be secured for passengers. In addition, the driving condition should also be secured under bad situations of the topographic slope, swampy land and the rest. In order to carry out above tests, a prototype vehicle through strength analysis of transmission design has been manufactured. Consequently, optimal design conditions on the power transmission with multi-purpose vehicle for various jobs are proposed such as an indication of optimal RPM and torque at a certain work situation. The performance test through the prototype of multi-purpose work vehicle is performed and the related data base is achieved. Finally, it is improved on troubles by the analysis of the results of R&D and provided the solutions on problems occurring to mass production in the future.