• Progress in Superconductivity and Cryogenics
• /
• v.23 no.4
• /
• pp.35-38
• /
• 2021

Conventional direct current (DC) rotating machines are usually used for crane and press machine using high torque in metal and steel industries, because of a constant output power along variable rotating speed. A general DC motor with permanent field magnets could not increase a magnetic flux density at a gap between armature coils and field magnets. However, a superconducting DC motor has field magnets composed with high temperature superconducting (HTS) coils and it could increase the magnetic flux density at the gap to over 10 times than those of a general DC motor by control the excitation current into HTS coils. The superconducting DC motor could be operated with extremely high torque and constant output power at a low rotational speed. In this paper, a 500 W superconducting DC rotating machine was conceptually designed with a LN₂ (Liquid Nitrogen) cooling method and the operation characteristics results of HTS field magnets were presented. The two no-insulation HTS magnets for a 500 W superconducting DC rotating machine were fabricated. The excitation current for the HTS magnets could be controlled from 0 to 40 A. This test results will be available to design large-sized HTS magnets for a number of hundred kW class superconducting DC rotating machine under LN₂ cooling system.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.990-992
• /
• 2002

30kW electrical power conversion system is delveloped for the variable speed wind turbine system. In the wind energy conversion system(WECS) a synchronous generator with field current excitation converts the mechanical energy into electrical energy. As the voltage and frequency of generator output vary according to the wind speed, a dc/dc boosting chopper is utilized to maintain constant dc link voltage. Grid connection type PWM inverter supply currents into the utility line by regulating the dc link voltage. The active power is controlled by q-axis current which the reactive power can be controlled by d-axis current reference change. The phase angle of utility voltage is detected using s/w PLL(Phased Locked Loop) in d-q synchronous reference frame. This scheme gives a low cost power solution for variable speed WECS.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.6
• /
• pp.545-556
• /
• 1990

A design method of a current source using 12-pulse phase-controlled rectifier (PCR) is presented. The critical inductance of the 12-pulse PCR is derived and it is shown that the critical inductance can be reduced using a current source. The control circuit of the 12-pulse PCR with an inner fast dynamic loop is proposed to give the frequency synchronism and to reduce the subharmonics due to the unbalance of the transformer of the power line. This circuit is analyzed and its dynamic loop is optimized. The optimal constant PIMF (proportional, integral and measurable variable feedback, and feedforware) controller is also designed using the time-weighted quadratic performance index. It is shown via experimental results that the proposed design method gives high dynamic and static performance of the current source using the 12-pulse PCR.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.105-111
• /
• 2004

In this paper, a new self-oscillated type high voltage power supply for the OPC(Organic Photo Conductor) charge is proposed, which has variable constant current source characteristics to improve the charge characteristic of the OPC roller. The proposed control method enables high quality printing characteristics regardless of the circumstance change such as ambient temperature or humidity by changing the current reference signal. To verify the proposed control method various experiments are performed.

• 전기의세계
• /
• v.30 no.8
• /
• pp.501-508
• /
• 1981

A novel and simple method of designing the current feedback loop for the velocity controller of an armature controlled dc servo motor is presented. Instead of constructing the usual tight current feedback loop, a loose current feedback loop is suggested in this paper. More specifically, the armature current is not limited to a fixed constant value, but instead the upper bound value is allowed to be variable along with the present motor speed. The control system designed in this manner shows that the motor under control is robust to a wide range of loading conditions and yields a more rapid transient characteristics which is verified experimentally by applying the method in the design of the controller for an Industrial robot.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.647-657
• /
• 2011

The present paper proposes a sliding mode control with fixed switching frequency for three-phase three-leg voltage source inverter based four-wire shunt active power filter. The aim is to improve phase current waveform, neutral current mitigation, and reactive power compensation in electric power distribution system. The performed sliding mode for active filter current control is formulated using elementary differential geometry. The discrete control vector is deduced from the sliding surface accessibility using the Lyapunov stability. The problem of the switching frequency is addressed by considering hysteresis comparators for the switched signals generation. Through this method, a variable hysteresis band has been established as a function of the sliding mode equivalent control and a predefined switching frequency in order to keep this band constant. The proposed control has been verified with computer simulation which showed satisfactory results.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.532-540
• /
• 2014

It is necessary to measure the current of rotor for controlling the active and reactive power generated by the stator side of the doubly fed induction generator (DFIG) system. There are offset and scaling errors in the current measurement. The offset and scaling errors cause one and two times current ripples of slip frequency in the synchronous reference frame of vector control, respectively. This paper proposes a compensation method to reduce their ripples. The stator current is variable according to the wind force but the rotor current is almost constant. Therefore input of the rotor current is more useful for a compensation method. The proposed method adopts the synchronous d-axis current of the rotor as the input signal for compensation. The ripples of the measurement errors can be calculated by integrating the synchronous d-axis stator current. The calculated errors are added to the reference current of rotor as input of the current regulator, then the ripples are reduced. Experimental results show the effectiveness of the proposed method.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.4
• /
• pp.191-198
• /
• 2015

The purpose of this study is to develope a current variation control system appropriate to the various LED(Light Emitting Diode) lamps using current control system equipped with microcontroller based voltage regulator of power driving circuit. For this, we will suggest a stable control system of current variation to enable a stable power-supply and current-control, consisting of circuit to minimize the affects on the LED forward voltage using variable resistance and compensating resistance. The method of constant current circuit and energy savings using microcontroller based voltage regulator suggested in this study can be applied to various a big capacity LED lamp to minimize the unnecessay heat generation and to control resistace delicately. Ultimately, we expect the results of this study will upgrade the reliability of LED lamp by supplying the current stably.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.2
• /
• pp.61-69
• /
• 2003

In this paper, we developed the U parameter test system which inspects the property of DC parameter for semiconductor products. The developed system is interfaced by IBM-PC. It is consisted of CPLD part, ADC (Analogue to Digital Converter), DAC (Digital to Analogue Converter), voltage/current source, variable resistor and measurement part. In the proposed system, we have designed the constant voltage source and the constant current source in a part. The CPLD part is designed by VHBL, which it generates the control and converts the serial data to parallel data. The proposed system has two test channels and it operates VFCS mode and CFVS mode. The range of test voltage is from 0[V] to 100[V], and the range of test current is from 0[mA] to 100[mA)]. The diode is tested. The test results have a good performance.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.148-150
• /
• 1996

This paper describes method of microstepping current control for linear pulse moor. The control method witch electrically subdivides 1 step of a LPM 125 micro step is realized using micro-step algorithm. The resolution of the system for microstepping is improved also by microstep control of driving current, which is followed by the increase of microstep subdivision coefficient, the precise position and velocity control of LPM can be realized and stabilization of the system is improved.