• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.443-447
• /
• 2009

Bismuth-antimony-telluride based thermoelectric thin film materials were prepared by metal organic vapor phase deposition using trimethylbismuth, triethylantimony and diisopropyltelluride as metal organic sources. A planar type thermoelectric device has been fabricated using p-type $Bi_{0.4}Sb_{1.6}Te_3$ and n-type $Bi_{2}Te_{3}$ thin films. Firstly, the p-type thermoelectric element was patterned after growth of $5{\mu}m$ thickness of $Bi_{0.4}Sb_{1.6}Te_3$ layer. Again n-type $Bi_{2}Te_{3}$ film was grown onto the patterned p-type thermoelectric film and n-type strips are formed by using selective chemical etchant for $Bi_{2}Te_{3}$. The top electrical connector was formed by thermally deposited metal film. The generator consists of 20 pairs of p- and n-type legs. We demonstrate complex structures of different conduction types of thermoelectric element on same substrate by two separate runs of MOCVD with etch-stop layer and selective etchant for n-type thermoelectric material. Device performance was evaluated on a number of thermoelectric devices. To demonstrate power generation, one side of the device was heated by heating block and the voltage output was measured. The highest estimated power of 1.3 ${\mu}m$ is obtained at the temperature difference of 45 K.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.808-814
• /
• 2010

Activities of nanostructure HZSM-5 and Co-ZSM-5 catalysts (with different Co-loading) for catalytic conversion of ethyl acetate and toluene were studied. The catalysts were prepared by wet impregnation method and were characterized by XRD, BET, SEM, TEM and ICP-AES techniques. Catalytic studies were carried out inside a U-shaped fixed bed reactor under atmospheric pressure and different temperatures. Toluene showed lower reactivity than ethyl acetate for conversion on Co-ZSM-5 catalysts. The effect of Co loading on conversion was prominent at temperatures below $400^{\circ}C$ and $450^{\circ}C$ for ethyl acetate and toluene respectively. In a binary mixture of organic compounds, toluene and ethyl acetate showed an inhibition and promotional behaviors respectively, in which the conversion of toluene was decreased at temperatures above $350^{\circ}C$. Inhibition effect of water vapor was negligible at temperatures above $400^{\circ}C$. An artificial neural networks model was developed to predict the conversion efficiency of ethyl acetate on Co-ZSM-5 catalysts based on experimental data. Predicted results showed a good agreement with experimental results. ANN modeling predicted the order of studied variable effects on ethyl acetate conversion, which was as follows: reaction temperature (50%) > ethyl acetate inlet concentration (25.085%) > content of Co loading (24.915%).

• Membrane and Water Treatment
• /
• v.9 no.4
• /
• pp.221-231
• /
• 2018

A new procedure to produce poly(vinylidene fluoride)/boron nitride hybrid membrane is presented for application in membrane distillation (MD) process. The influence of hexagonal boron nitride (h-BN) incorporation on the performance of the polymeric membranes is studied through the present investigation. For this aim, h-BN nanopowders were successfully synthesized using the simple chemical vapor deposition (CVD) route and subsequent solvent treatments. The resulting h-BN nanosheets were blended with poly(vinylidene fluoride) (PVDF) solution. Then, the prepared composite solution was subjected to phase inversion process to obtain PVDF/h-BN hybrid membranes. Various examinations such as scanning electron microscopy (SEM), wettability, permeation flux, mechanical strength and liquid entry pressure (LEP) measurements are performed to evaluate the prepared membrane. Moreover, Air gap membrane distillation (AGMD) experiments were carried out to investigate the salt rejection performance and the durability of membranes. The results show that our hybrid PVDF/h-BN membrane presents higher water permeation flux (${\sim}18kg/m^2h$) compared to pristine PVDF membrane. In addition, the experimental data confirms that the prepared nanocomposite membrane is hydrophobic (water contact angle: ${\sim}103^{\circ}$), has a porous skin layer (>85%), as well competitive fouling resistance and operational durability. Furthermore, the total salt rejection efficiency was obtained for PVDF/h-BN membrane. The results prove that the novel PVDF/h-BN membrane can be easily synthesized and applied in MD process for salt rejection purposes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1089-1095
• /
• 2011

Numerical simulation is performed for nucleate boiling on a micro-finned surface, which has been widely used to enhance heat transfer, by solving the equations governing the conservation of mass, momentum, and energy in the liquid and vapor phases. The bubble motion is determined by a sharp-interface level-set method, which is modified to include the effect of phase change and to treat the no-slip and contact-angle conditions, as well as the evaporative heat flux from the liquid microlayer on immersed solid surfaces such as micro fins and cavities. The numerical results for bubble formation, growth, and departure on a microstructured surface including fins and cavities show that the bubble behavior during nucleate boiling is significantly influenced by the fin-cavity arrangement and the fin-fin spacing.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.6
• /
• pp.261-264
• /
• 2012

In this paper, we investigated characteristics of etching induced surface morphology variation by wet etching of GaN epilayer were grown on sapphire (0001) substrate by hydride vapor phase epitaxy (HVPE). As a results of scanning electron microscope (SEM) observation, three types of hexagonal etch pits (Edge, Screw, Mixed) were formed by the GaN epilayer thickness variations. A lot of etch pits, attributed to screw and mixed type TD, were observed at thinner epilayer, leading to high etch pit density. On the other hand, the thickness of GaN epilayer increased with the number of etch pits corresponding to edge and mixed dislocations, which are the majority of TDs are observed.

• Korean Journal of Food Science and Technology
• /
• v.35 no.4
• /
• pp.738-742
• /
• 2003

In order to estimate the mass transfer characteristics of absorption into alcohol solution of aroma compounds such as cineol, myrecene and pinene which are major aroma compounds of rosemary, dimensionless Henry's constant in 70% ethyl alcohol concentration and aroma concentration with different ethyl alcohol concentration were analyzed. From the results of measurement of vapor phase concentration of aroma compounds with different ethyl alcohol concentration, headspace concentrations of all of three aroma compounds were decreased as ethyl alcohol concentration increased. But those patterns were slightly different. Dimensionless Henry's constant equation (Hi) of cineol compound with ethyl alcohol concentration (x) was as follows: $Hi=(-5.75+x)/(-7017.6+257.3{\times}x)$. Dimensionless Henry's constants of cineol, myrecene and pinene in 1 atm, $25^{\circ}C$ and 70% ethyl alcohol concentration were 0.0058, 0.0182 and 0.0365, respectively.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.667-671
• /
• 1998

The photoluminescence (pL) characteristics of hydride vapor phase epiyaxy (HVPE) grown GaN films on $MgAl_{2}O_{4}$ substrate were investigated with several growth conditions. The GaN films on $MgAl_{2}O_{4}$ substrate is autodoped with Mg atoms which thermally out-diffused from substrate lead to a PL characteristics of impurity doped ones. The Mg-related emission band intensity decreased with growth temperature may due to the evaporation of Mg atoms at the GaN film surfaces. and it also decreased with GaN film thicknesses. We can estimate the diffusion coefficient of Mg atoms in GaN under the consideration of diffusion phenomena between two infinite solids lead to a value of D= 2$\times$$lO^{-10}\textrm{cm}^2/sec.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.386-391
• /
• 2018

An epitaxial GaN layer was grown on a cone-shape-patterned sapphire substrate (PSS) (Sample A) and an AlN-buffered PSS (Sample B) with two growth steps under the same process conditions by employing the hydride vapor phase epitaxy (HVPE) method. We have investigated the characteristics of the GaN layer grown on two kinds of substrates at each growth step. The cross-sectional SEM image of the GaN layer grown on the two types of substrates showed growth states of GaN layers formed during the 1st and 2nd growth steps with different growth durations. Dislocation density was obtained by calculation using the FWHM value of the rocking curve for (002) and (102). Sample A showed 2.62+08E and 6.66+08E and sample B exhibited 5.74+07E and 1.65+08E for two different planes. The red shift was observed is photoluminescence (PL) analysis and Raman spectroscopy results. GaN layers grown on AlN-buffered PSS exhibited better optical and crystallographic properties than GaN layers grown on PSS.

• Journal of Korean Society of Disaster and Security
• /
• v.10 no.2
• /
• pp.29-34
• /
• 2017

LPG is a substance that requires a lot of attention because it can cause fatal damage to people and environment when an accident occurs. LPG is frequently accidents in transportation facilities as well as fixed facilities, among which LPG tank lorries are the most frequent accidents. When the LPG tank is evacuated, the LP gas leaks into two phases, leaks mostly to the gas and leaks to some liquid. At this time, the leaked gas will also sink downward because it is heavier than air, and if it continues to leak, it may form an explosion and explode by the ignition source. The purpose of this study is to present the evacuation distance by analyzing the effect distance of the LPG liquefied petroleum gas in the event of explosion. As a result of calculation of the scattering radius of the fragment, the cylinder fragment was scattered up to 561 m. Therefore, it is appropriate to set the distance to be escaped when the LPG tanker leaks to 561m or more.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.521-522
• /
• 2006

In this paper, hybrid air-water discharges were used to develop an optimal condition for providing a high level of water decomposition for hydrogen yield. Electrical and optical phenomena accompanying the discharges were investigated along with feeding gases, flow rates, and point-to-plane electrode gap distance. The primary focus of this experiment was put on the optical emission of the near UV range, with the energy threshold sufficient for water dissociation and excitation. The $OH(A^{2+},'=0\;X^2,"=0$) band's optical emission intensity indicated the presence of plasma chemical reactions involving hydrogen formation. In the gaseous atmosphere saturated with water vapor the OH(A-X) band intensity was relatively high compared to the liquid and transient phases although the optical emission strongly depended on the flow rate and type of feeding gas. In the gaseous phase discharge phenomenon for Ar carrier gas transformed into a gliding arc via the flow rate growth. OH(A-X) band's intensity increased according to the flow rate or residence time of He feeding gas. Reciprocal tendency was acquired for $N_2$ and Ar carrier gases. The peak value of OH(A-X) intensity was observed in the proximity of the water surface, however in the cases of Ar and $N_2$ with 0.5 SLM flow rate peaks shifted to the region below the water surface. Rotational temperature ($T_{rot}$) was estimated to be in the range of 900-3600 K, according to the carrier gas and flow rate, which corresponds to the arc-like-streamer discharge.