• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1291-1292
• /
• 2006

In the structure of ITO/HIL/$Alq_3$/Al device, we investigated an efficiency improvement of the Organic Light-Emitting Diodes depending on thickness variation of hole-injection layer. Using the thermal evaporation in a base vacuum $5{\times}10^{-5}$[Torr], we have measured efficiency after the $Alq_3$ was evaporated to 100 [nm] as a deposition rate $1.5[{\AA}/s]$. In optimal condition, when PTFE thickness increased from 0 to 3.0 [nm], we have obtained that an optimal thickness of PTFE was 2.5 [nm]. And using the PTFE, luminance efficiency and external quantum efficiency of the device were improved by 12.8 times and 11.1 times, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1983-1985
• /
• 2005

This paper describes moisture content, dielectric strength and dielectric properties of thermally accelerating aged insulating paper as varnish treatment. Kraft, nomex paper were impregnated with diluted varnish, varnish and solvent were diluted in the ratio of 40wt%, in vacuum condition, and then completely dried. To analysis of papers were influenced by varnish treatment, we applied thermal stress, and then measured moisture content, dielectric strength and relative permittivity, $tan{\delta}$ as varnish impregnated papers.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.59-70
• /
• 1990

Crack of breaking toughness of most Ceramics material is 1-5MPa .root.m but that of Zirconia Ceramics is improved to be 6-8MPa .root.m and its development of machining difficult-to-machine material is on the rise as urgent subject. For general Zirconia Ceramics machining, diamond grinding wheel is generally used by selecting an appropriate one and establishing grinding condition but due to such limitations as economics, grinding efficiency and machining geometry, great interest in machining method being used for diamond tool is emphasized. But it is reported that diamond tool is oxidized by cutting heat in the air and is graphitized in vacuum, which causes bad effects on tool life. In this study, to restraint cutting heat the internal side of tool is cooled, and restraint low temperature cooling system and being experimented. Further, the machinability of diamond tool for Zirconia Ceramics machining is analyzed with respect to tool wear and stress.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.217-218
• /
• 2007

Aluminum 분말과 고분자를 혼합하여 고분자-금속 복합재료(polymer-metal composite)를 만들어 copper foil과 기판의 접착력을 평가하였다. Tape casting 방법을 이용하여 sheet 만들고 vacuum lamination으로 PCB(Printed Circuit Board)기판을 제조한 후 포토공정으로 peel strength pattern을 형성하였으며, 본 연구에서는 최적의 aluminum 조건을 찾기 위하여 압력, 온도, copper foil의 표면 상태와 silane 표면 코팅에 따른 aluminum-polymer복합재료의 peel strength의 변화를 확인하였다. 최적의 조건은 silane 표면 코팅 처리를 한 aluminum 분말로 $210^{\circ}C$에서 $9.7kg/cm^2$ 압력으로 matte면의 돌기 크기가 크며, 응집이 잘 되어있는 copper foil을 사용하여 13.89N의 우수한 peel strength를 구현 할 수 있었다.

• Applied Science and Convergence Technology
• /
• v.26 no.4
• /
• pp.91-94
• /
• 2017

AThe effect of localized surface plasmon on silicon substrates was studied using silver nanoparticles. The nanoparticles were formed by self-arrangement through the surface energy using rapid thermal annealing (RTA) technique after the thin nanolayer of silver was deposited by thermal evaporation. By the theoretical calculation based on Mie scattering and dielectric function of air, indium tin oxide (ITO), and silver, the strong peak of scattering cross section of silver nanoparticles was found at 358 nm for air, and 460 nm for ITO, respectively. Accordingly, the strong suppression of reflectance under the condition of induced light of $30^{\circ}$ occurred at the specific wavelength which is almost in accordance with peak of scattering cross section. When the external quantum efficiency was measured using silicon solar cells with silver nanoparticles, there was small enhancement peak near the 460 nm wavelength in which the light was resonated between silver nanoparticles and ITO.

• Journal of Welding and Joining
• /
• v.29 no.6
• /
• pp.45-48
• /
• 2011

In this research, laser welding of automotive transmission components was investigated to replace electron beam welding which is normally conducted under vacuum condition. Fiber laser welding was applied to the automotive transmission components - hub clutch and annulus gear. In the component welding, the laser welding parameters were optimized to eliminate spatters and the end crater. By applying laser welding to the transmission parts, the process time could be reduced up to 70% compared with the current electron beam welding process.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.4
• /
• pp.38-52
• /
• 1982

The effect of propylene oxide, butylene oxide, furan resin, and vinylpyrrolidinone in controlling wood dimensional stability have been examined. Wood in the green or ovendry condition was treated with various chemical treatments using a vacuum-pressure procedure, and treated specimens were tested for tangential sweelling, moisture gain, and changes in sorption hysteresis. Results' indicate that propylene oxide, and butylene oxide enhanced with the crosslin king agent trimethylol propane trimethacrylate and applied to ovendry wood were the most efficient chemical treatments in controlling tangential sweeling caused by liquid water or water vapor, and in reducing water vapor adsorption. The sorption behavior of treated wood as depicted by the ratios of sorption was "very favorable" in most instances. In the particular case of furan resin treatments, ratios of sorption were improved from 25 to 100 percent as compared to those of untreated wood.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.2
• /
• pp.53-57
• /
• 2019

In this study, we prepared sputtering cathode for large sputtering thin film in the facing targets sputtering(FTS) system. Before fabrication of cathode equipment, we investigated optimal magnetic flux in the sputtering cathode by using magnetic field stimulation(Comsol). According to the result of magnetic field stimulation, we manufactured the cathode. After we mounted laboratory-designed cathode on FTS system, the discharge properties were observed in vacuum condition. In addition, ITO films were deposited on glass substrate and their electrical and optical properties were investigated by various measurements (four-point probe, UV-VIS spectrometer, field emission scanning electron microscopy(FE-SEM), Hall-effect measurement).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.272-274
• /
• 2008

A development of hydrazine decomposition catalyst for monopropellant thruster has been performed by Korea Aerospace Research Institute(KARI). The goal of this development is to product a catalyst showing the equivalent performance with space-proven catalysts. Catalyst production and physical/chemical analysis were conducted by Chonnam National University and the analysis result was compared with the result of other catalysts and our own specification. Using the developed prototype catalyst, short firing test was performed in a reactor to verify basic performance of catalyst. After the successful reactor test, hot firing tests were carried out in atmospheric and vacuum condition using 5N thruster to verify durability and safety of catalyst. In this paper, the catalyst development status will be presented.

• Archives of Metallurgy and Materials
• /
• v.64 no.3
• /
• pp.917-920
• /
• 2019

Usually porous metals are known as relatively excellent characteristic such as large surface area, light, lower heat capacity, high toughness and permeability for exhaust gas filter, hydrogen reformer catalyst support. The Ni alloys have high corrosion resistance, heat resistance and chemical stability for high temperature applications. In this study, the Ni-based porous metals have been developed with Hastelloy powder by gas atomization and water atomization in order to find the effects of powder shape on porous metal. Each Hastelloy powder is pressed on disk shape of 2 mm thickness with 12 tons using uniaxial press machine. The specimens are sintered at various temperatures in high vacuum condition. The pore properties were evaluated using Porometer and microstructures were observed with SEM.