• Composites Research
• /
• v.35 no.1
• /
• pp.42-46
• /
• 2022

In this study, when the carbon fiber composite was manufactured, the correlation between the porosity and mechanical properties according to the number of glass fiber felts laminated together and the stacking sequence was confirmed. The carbon fiber composite was manufactured by stacking glass fiber felts, which are highly permeable materials, and using vacuum assisted resin transfer molding (VARTM). Porosity was measured by photographing the cross-section of the specimen with an optical microscope and then using porosity calculation code of MATLAB, and mechanical properties were measured for tensile strength, modulus by tensile test. Furthermore, Pearson correlation coefficient between porosity and mechanical properties was calculated to confirm the correlation between two variables. As a result, the number of glass fiber felt increased and the distance from the center of laminated composites increased, the porosity increasing were confirmed. In addition, tensile strength/modulus showed a weak positive correlation with porosity. Also, in order to confirm the effect of only porosity on tensile strength and modulus, mechanical properties calculated by CLPT (Classical Laminate Plate Theory) and experimental values were compared, and the difference in tensile strength showed a strong positive correlation with porosity and the difference in modulus showed a weak positive correlation with porosity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.27-36
• /
• 2019

The demand for a low dispersion lens with a small refractive index and a high refractive index is increasing, and accordingly, there is an increasing need for a releasable protective film with high heat resistance and abrasion resistance. On the other hand, the optical industry has not yet established a clear standard for the manufacturing process and quality standards for mold-releasing protective films used in aspheric glass lens molding. Optical lens manufacturers treat this technology as proprietary information. In this study, an experiment was conducted regarding the optimization of ion etching, magnetron, and arc current at each source and filter part, and bias voltage in FCVA (filtered cathode vacuum arc)-based Ta-C thin film coatings. This study found that compared to iridium-rhenium alloy thin film sputtering products, the coating conditions were improved by approximately 50%, 20%, and 40% in terms of thickness, hardness, and adhesive strength of the film, respectively. The thin-film coating process proposed in this study is expected to contribute significantly to the development and utilization of glass lenses, which will help enhance the minimum mechanical properties and quality of the mold-release thin film layer required for glass mold surface forming technology.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1943-1945
• /
• 1996

In this paper, we developed a modified direct bonding method for the application of vacuum devices. By the proposed method, we successfully bonded the following materials: Si-Si, Si-$SiO_2$-Si, glass-Si, and glass-$SiO_2$-Si. In our experiments, we used corning #7070 wafer type glass and (100) or (110) single crystalline silicon wafers. In order to enhance the initial bonding strength we contacted the materials to be bonded as D. I. water wetted on the surfaces and evaporated the water under the room temperature and atmosphere environment. Finally we realized the glass bonding by simple direct bonding method which has been performed by electrostatic bonding method until now.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.1
• /
• pp.75-80
• /
• 2005

In this thesis, We Fabricated Cu thin films of 1000 $\AA$, 3000 $\AA$, and 6000 $\AA$ thickness on the single crystal sapphire, polycrystal alumina, and amorphous slide glass substrates deposited by electron beam evaporation(EBE) method. We investigated properties of resistivity and adhesion of these Cu thin films under various conditions, substrate temperature(room temperature, 10$0^{\circ}C$, 20$0^{\circ}C$ under vacuum) and annealing temperatures(400 $^{\circ}C$, 600 $^{\circ}C$ for 30 min after the deposition). We found that these adhesion was increased in order of slide glass, sapphire, and alumina. The adhesion of the Cu thin films on alumina was high value about 4 times, compared with that of the Cu thin films on slide glass. We found that these resistivities were decreased with increasing substrate temperature and thin film thickness. The resistivity(2.05 $\mu$Ω\ulcornercm) of the Cu thin films with 6000 $\AA$ thickness at 200 $^{\circ}C$ on the slide glass was low value, compared with that of aluminum(2.66 $\mu$Ω\ulcornercm).

• Journal of the Korean Magnetics Society
• /
• v.9 no.5
• /
• pp.245-250
• /
• 1999

The effect of substrate and oxidization time on $substrate /Py/Al_2O_3/Co\;(Py=Ni_{81}Fe_{19})$ tunnel junction was studied. Samples were prepared without breaking vacuum by changing shadow masks in-situ. The resistance of tunnel junctions increased, but measured MR decreased with oxidization time. Negative MR observed for samples of tunnel resistivity lower than 0.17 M$\Omega$ $({\mu}m)^2$. MR resistivity decreased with the change of substrates in the order of thermally oxidized Si(111), Si(100), Coring Glass 2948, Corning Glass 7059. Sign change and the variation of MR was explained with non uniform current effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.374-375
• /
• 2006

This paper describes anodic bonding characteristics of MCA to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with the same properties were deposited on MCA under optimum RF sputter conditions (Ar 100 %, input power $1\;W/cm^2$). After annealing at $450^{\circ}C$ for 1 hr, the anodic bonding of MCA to Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in $110^{-6}$ Torr vacuum condition. Then, the MCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation and simulation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity being 0.05-0.08 %FS. Moreover, any damages or separation of MCNSi bonded interfaces did not occur during actuation test. Therefore, it is expected that anodic bonding technology of MCNSi-wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• Tribology and Lubricants
• /
• v.35 no.2
• /
• pp.106-113
• /
• 2019

We investigated the application of tetrahedral amorphous carbon (ta-C) coatings to fabricate a glass lens manufactured using a glass molding process (GMP). In this work, ta-C coatings with different thickness (50, 100, 150 and 200 nm) were deposited on a tungsten carbide (WC-Co) mold using the X-bend filter of a filtered cathode vacuum arc. The effects of thickness on mechanical and tribological properties of the coating were studied. These ta-C coatings were characterized by atomic force microscopy, scanning electron microscopy, nano-indentation measurements, Raman spectrometry, Rockwell-C tests, scratch tests and ball on disc tribometer tests. The nano-indentation measurements showed that hardness increased with an increase in coating thickness. In addition, the G-peak position in the Raman spectra analysis was right shifted from 1520 to $1586cm^{-1}$, indicating that the $sp^3$ content increased with increasing thickness of ta-C coatings. The scratch test showed that, compared to other coatings, the 100-nm-thick ta-C coating displayed excellent adhesion strength without delamination. The friction test was carried out in a nitrogen environment using a ball-on-disk tribometer. The 100-nm-thick ta-C coating showed a low friction coefficient of 0.078. When this coating was applied to a GMP, the life time, i.e., shot counts, dramatically increased up to 2,500 counts, in comparison with Ir-Re coating.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.3
• /
• pp.105-110
• /
• 2015

The fiber-reinforced endodontic posts were prepared using a photocurable resin and a glass fiber. The mechanical property of the posts increased with increasing density of glass fiber and the micro-pores in the post were removed by a vacuum impregnation process. To improve the interfacial adhesion between glass fiber and polymer, silane coupling agent was used. The surface treatment of glass fiber increased the surface wettability of resing on glass fiber and increased the adhesion property with resin, consequently improved the mechanical property of posts.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.301-308
• /
• 2003

Glass-infiltrated alumina, which can be used as an all-ceramic dental crown, was prepared. The glasses in the system of SiO$_2$-B$_2$O$_3$-Al$_2$O$_3$-CaO-La$_2$O$_3$with various amount of $Al_2$O$_3$infiltrated into a porous sintered alumina. The effect of $Al_2$O$_3$on the infiltration characteristics and its mechanical strength were studied. The corrosion of the sintered alumina by infiltrated glasses was prevented by increasing the amount of $Al_2$O$_3$in the glass batches, this increased the bending strength of the glass infiltrated alumina composite. The crack like voids in the sintered alumina was a cause of the deteriorating the mechanical strength of the composite, and this can be eliminated by sintering the alumina at 130$0^{\circ}C$. Glass infiltration under the vacuum atmosphere enhanced the hording strength of the composite up to 453$\pm$31 MPa.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.358-358
• /
• 2012

The application of BZO (Boron-doped Zinc Oxide) films use as the TCO(Transparent Conductive Oxide) material for display and solar cell industries, where the conductivity of the BZO films plays a critical role for improvement of cell performance. Thin BZO films are deposited on glass substrates by using RF sputter system. Then charging flow rates of O2 gas from zero to 10 sccm, thereby controlling the impurity concentration of BZO. BZO deposited on soda lime glass and RF power was 300 W, frequency was 13.56 MHz, and working pressure was $5.0{\times}10-6$ Torr. The Substrate and glass between distance 200 mm. We measured resistivity, conductivity, mobility by hall measurement system. Optical properties measured by photo voltaic device analysis system. We measured surface build according to oxygen flow rate from XPS (X-ray Photoelectron Spectroscopy) system. The profile of the energy distribution of the electrons emitted from BZO films by the Auger neutralization is measured and rescaled so that Auger self-convolution arises, revealing the detail structure of the valence band. It may be observed coefficient ${\gamma}$ of the secondary electron emission from BZO by using ${\gamma}$-FIB (Gamma-Focused Ion Beam) system. We observed the change in electrical conductivity by correlation of the valence band structure. Therefore one of the key issues in BZO films may be the valence band that detail structure dominates performance of solar cell devices. Demonstrating the secondary electron emission by the Auger neutralization of ions is useful for the determination of the characteristics of BZO films for solar cell and display developments.