• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.426-430
• /
• 2003

본 연구에서는 초음파현미경의 기하학적 원리와 초음파현미경의 특징중 하나인 V(z)곡선의 간섭파형을 시뮬레이션 하였고, 실제 초음파현미경의 V(z)곡선법을 이용하여 미소영역에서의 누설탄성표면파 음속을 측정하였다. 초음파현미경을 이용한 V(z)곡선법의 음속측정결과가 시뮬레이션 음속값과 큰차이를 보이지 않으므로 미소영역에 초음파현미경의 V(z)곡선법을 적용하여 초음파의 음속측정이 가능함을 확인하였다. 이는 향후 초음파현미경을 이용하여 미세한 재료의 물성평가에 적용할 수 있을 것으로 기대된다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.5
• /
• pp.518-524
• /
• 2004

The feasibility of Y(z) curve method of scanning acoustic microscope using high frequency transducer was experimentally studied for assessment of the thermal degradation in Co-based superalloy. Thermal degradation was performed to simulate the microstructural changes in Co-based superalloy arising from long term exposure at high temperature. Longitudinal wave velocity measured by pulse echo method using 10MHz transducer and leaky surface acoustic wave (LSAW) velocity measured by V(z) curve method using 200MHE transducer were measured to investigate the effect on thermal degradation. Ultrasonic velocity decreased as the aging time increased in both ultrasonic waves. Moreover, the low frequency longitudinal wave velocity decreased a little. Otherwise, the high frequency LSAW velocity drastically decreased up to a maximum of 4.7% at the aging time of 4,000hours. A good correlation was found between LSAW and Vickers hardness. Consequently, V(z) curve method of SAM using high frequency transducer could be a potential tool for assessing thermal degradation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.291-296
• /
• 2006

The residual stress in shot-peened Al 7075 alloy was evaluated using surface acoustic wave (SAW). Shot peening was conducted to produce a variation in the residual stress with the depth below the surface under a shot velocity of 30 m/s. The SAW velocity was measured from the V(z) curve using a scanning acoustic microscopy (SAM). The Vickers hardness profile from the surface showed a significant work hardening near the surface layer with a thickness of about 0.25 mm. As the residual stress became more compressive, the SAW velocity increased, whereas as the residual stress became more tensile, the SAW velocity decreased. The variation in the SAW velocity through the shot peened surface layer was in good agreement with the distribution of the residual stress measured by X-ray diffraction technique.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.4
• /
• pp.393-400
• /
• 2012

In recent years, nano-structured thin film systems are often applied in industries such as MEMS/NEMS device, optical coating, semiconductor or like this. Thin films are used for many and varied purpose to provide resistance to abrasion, erosion, corrosion, or high temperature oxidation and also to provide special magnetic or dielectric properties. Quite a number of articles to evaluate the characterization of thin film structure such as film density, film grain size, film elastic properties, and film/substrate interface condition were reported. Among them, the evaluation of film adhesive to substrate has been of great interest. In this study, we fabricated the polymeric thin film system with different adhesive conditions to evaluate the adhesive condition of the thin film. The nano-structured thin film system was fabricated by spin coating method. And then V(z) curve technique was applied to evaluate adhesive condition of the interface by measuring the surface acoustic wave(SAW) velocity by scanning acoustic microscope(SAM). Furthermore, a nano-scratch technique was applied to the systems to obtain correlations between the velocity of the SAW propagating within the system including the interface and the shear adhesive force. The results show a good correlation between the SAW velocities measured by acoustic spectroscope and the critical load measured by the nano-scratch test. Consequently, V(z) curve method showed potentials for characterizing the adhesive conditions at the interface by acoustic microscope.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.171-175
• /
• 2014

In this study, we suggest a method to measure the thickness of thin films nondestructively using the dispersion characteristics of a surface acoustic wave propagating along the thin film surface. To measure the thickness of thin films, we deposited thin films with different thicknesses on a Si (100) wafer substrate by controlling the deposit time using the E-beam evaporation method. The thickness of the thin films was measured using a scanning electron microscope. Subsequently, the surface wave velocity of the thin films with different thicknesses was measured using the V(z) curve method of scanning acoustic microscopy. The correlation between the measured thickness and surface acoustic wave velocity was verified. The wave velocity of the film decreased as the film thickness increased. Therefore, thin film thickness can be determined by measuring the dispersion characteristics of the surface acoustic wave velocity.

• Analytical Science and Technology
• /
• v.12 no.6
• /
• pp.528-533
• /
• 1999

The total iodine is determined in serum, fresh milk and feed additive by ICP-MS. The preparation involves only a 25-fold dilution with a diluent by direct nebulization in the plasma. The diluent composition is $NH_4OH$(0.5% v/v)+$CH_3OH$(5% v/v) and the abundance of iodine is measured at m/z=127. The calibration curve was linear over the ranges $0-100{\mu}g/L$ with $R^2=0.99$ for iodine. The detection limit of this method is $0.084{\mu}g/L$ for iodine. The relative error range of milk powder SRM in optimum condition is 2.30%-4.73%. The concentration ranges of iodine in the serum, fresh milk, feed additive were $12.4-40.2{\mu}g/L$, < 0.01-3.11 mg/L, < $10^{-7}-2.60g/kg$ respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.609-615
• /
• 2005

The effects of Zr/Ti concentration ratio in PLZT (10/y/z) thin films prepared by sol-gel method are investigated for the NVFRAM application. As Ti amount of Zr/Ti concentration ratio increases, the dielectric constants at 10 kHz decrease from 550 to 400, while the loss tangents increase from 0.028 to 0.053 and the leakage current densities at 170 kV/cm decrease from $1.64\times10^{-6}$ to $1.26\times10^{-7}\;A/cm^2$. In the results of hysteresis loops measured at $\pm170kV/cm$, the remanent polarization and the coercive field increase from 6.62 to $12.86{\mu}C/cm^2$ and from 32.15 to 56.45 kV/cm, respectively, according to the change from 40/60 to 0/100 in Zr/Ti concentration ratio. Fatigue and retention properties also improve much as the Zr/Ti concentration ratio change from 40/60 to 0/100. After applying $10^9$ square pulses with $\pm5V$, the remanent polarization of the PLZT (10/40/60) thin film decreases $50\%$ from the initial state while that of the PLZT (10/0/100) thin film decreases $28\%$. In the results of retention measurements of 10s s, the remanent polarization of the PLZT (10/0/100) thin film dec.eases only $10\%$ from the initial state, while that of the PLZT (10/40/60) thin film decreases $40\%$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.2
• /
• pp.40-47
• /
• 1993

Composites composed of a precipitation harden 2124 alloy matrix reinforced by SiC whiskers, which are fabricated by powder metallugy, are suscepttible to fatigue damage due to the pile-up of moving dislocation and the microcrack initiation along SiC-Al interfaces, especially at the external surfaces of a body. The initial process, such as pile-up of dislocation or microcrack, that corresponds to the stage I during fatigue failure process are too small to be detected and characterized by conventional ultrasonic technique. This paper describes the applicability of an acoustic microscope with Line-Focus-Beam(LFB) lens of 225MHz to evaluate fatigue damage of SiC whiskers reinforced Al alloy. The specimens which were 6.6mm thick, 13mm wide, and 105mm long in the gage section were fatigued in tension-tension under load control. The velocity of leaky surface and leaky pseudosurface acoustic waves are obtained by FFT analysis technique from V(z) curve which is a record of output of piezoelectric transducer. These results are discussed with the change of number of fatigue cycles. The result obtained by acoustic microscope is compared with that by ultrasonic technique generated at 5MHz with conventional surface wave transducers.

• Electrical & Electronic Materials
• /
• v.6 no.3
• /
• pp.241-247
• /
• 1993

본 연구에서는 투광성 0.085Ba(L $a_{1}$2/N $b_{1}$2/) $O_{3}$- 0.915Pb(Z $r_{y}$ $Ti_{1-y}$) $O_{3}$(0.45.leq.y.leq.0.70)세라믹을 2단 소성법으로 제작한 후, PbZr $O_{3}$조성 및 온도에 따른 구조적, 강유전적특성을 측정하였다. XRD측정 결과, PbZr $O_{3}$조성이 감소할수록 결자상수 및 단위격자 체적은 감소하였으며 시편의 결정구조는 입방정계에서 능면체정계, 정방정계로 변화되었다. 8.5/60/40시편의 경우 포화분극, 잔류분극 및 항전계가 각각 33.28[.mu.C/$cm^{2}$], 4.15[kV/cm]로 전형적인 메모리 특성을 나타내었으며 PbZr $O_{3}$조성이 증가함에 따라 강유전 이력곡선은 slim loop특성을 나타내었다. 잔류분극은 온도가 증가함에 따라 감소하였으며 특히 PE-FE상경계 부근에 위치한 조성의 경우, 상전이 온도 이하의 온도에서 급격히 감소하는 경향을 나타내었다.다.

• Korean Journal of Food Science and Technology
• /
• v.30 no.3
• /
• pp.630-637
• /
• 1998

Enzymatic properties of immobilized transglucosidase (TG) from Aspergillus niger was characterized and compared with soluble TG. Michaelis-Menten constant $(K_m)$ and maximum velocity $(V_{max})$ of immobilized TG were $122\;mM,\;3.9{\times}10^{-2}\;mM/min$ and in case of soluble TG, 21 mM, 0.4 mM/min. The optimum pH of immobilized TG was pH 5.0 like soluble TG but immobilized TG showed 16% and 45% higher activity than soluble TG at pH 5.0 and pH 6.0. Both of immobilized TG and soluble TG were stable from pH 2.0 to pH 9.0, and therefore their activities in these pH ranges were remained more than 90%. The temperature was optimal at $60{\sim}70^{\circ}C\;and\;70{\sim}80^{\circ}C$ for soluble TG and immobilized TG, respectively. The thermal stability of immobilized TG was significantly improved than that of soluble TG, and immobilized TG retained $32{\sim}40%$ higher activity than soluble TG. D-values from thermal inactivation of immobilized TG were 7690 sec at $65^{\circ}C$, 83 sec at $75^{\circ}C$, 7.2 sec at $80^{\circ}C$. Z-values of soluble and immobilized TG were $6.4^{\circ}C\;and\;5.3^{\circ}C$, respectively. The little difference of activation energies of soluble TG and immobilized TG supposed that there was little difference in mass transfer limitation during the reaction of soluble TG and immobilized TG.