• Journal of Bio-Environment Control
• /
• v.23 no.1
• /
• pp.1-10
• /
• 2014

This study analyzed the efficiency and uniformity by measuring the temperature change depending on the position in the chamber with the use of QRD (quadratic residue diffusor) microwave capable of inducing even sterilization by changing wavelength phase difference and enhancing the effect on low power. The results are summarized as follows: When irradiating 7 kW of QRD microwave, the highest efficiency was obtained at 35 cm height and in the center of the chamber. When irradiating 5 kW of QRD microwave, high efficiency was obtained on the sides of the chamber. When irradiating 3 kW of QRD microwave to Magnetrons 1, 2 and 3, the temperature uniformity according to the position of the bars was similar in the position of Bar 1 and 2. When irradiating 3 kW of QRD microwave to Magnetrons 3, 4 and 5, the temperature increased by approximately 10 to 20% in Bar 3. When irradiating 5, 7 and 9 kW of magnetron, the average temperature during the irradiation time increased in a similar form independently of the position of the bars. On the other hand, the efficiency of the chamber's proper internal volume was not necessarily proportional to the irradiation dose. When irradiating 3 kW of magnetron for 60 120 and 180 seconds, the temperature increased by approximately 5 to 10 at the edge of the chamber according to the irradiation position of magnetron. The temperature distribution for each position in the horizontal plane was relatively uniform, and the temperature had a tendency to slightly increase at the edge. When irradiating 5, 7 and 9 kW of magnetron, the temperature relatively evenly increased independently of the position of the bars. It was thought necessary to increase the irradiation dose by approximately 10 to 20% by considering the difference in temperature rise according to the position of magnetron.

• Journal of Bio-Environment Control
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2017

This experiment was conducted to analyze the effect of drainage reuse rate on the growth and fruiting of summer paprika in closed hydroponic cultivation. The experiment was carried out for 25 weeks from March to September 2015 with 0, 20, 30, 50% mixing ratio of waste nutrient solution using non - recycling hydroponic cultivation as a control. As a result, stem diameter of the test was different in the groups 1 and 2, but no difference showed as the group progressed more than 3 groups. L.A.I tended to decrease with increasing drainage mixing ratio. The number of nodes in the 50% reuse test group was 1.4 compared to the control group, but there was no significant difference. The number of harvested nodes was significantly different in the control group (11.1 nodes) and the 50% reuse test group (8.7 nodes), and the harvested nodes tended to decrease as the drainage was reused. The ratio of harvest was also the same as that of the harvesting node, and the control was the highest at 33.2% and the lowest at the 50% reuse test at 27.6%. Relative yields were reduced by 30%, 35% and 45% in the control group in the first group, and this tendency was also observed in the second and fourth groups. However, in the 3 and 5 groups, the production of 50% test group increased by 13% and 5%. The ratio of unmarketable fruit was increased 2%, 4%, 4%, and 7% in 0%, 20%, 30% and 50% reuse test, respectively. In conclusion, if the decrease in yield due to the decline in early growth is carefully managed, even if the imbalance of inorganic ions occurs after the mid-term growth, the growth of the crop will enter into a stable period and the re-use will not be worried about the growth and the yield decrease.

• Journal of Life Science
• /
• v.30 no.5
• /
• pp.428-433
• /
• 2020

In this study, we created pupal stage extracts of Apis mellifera L. drones for use in cosmetic materials. The effect of the drone pupae extract (DPE) on HDF cells was assessed for analysis of anti-wrinkle activity by collagen or collagenase gene expression, and the skin-lightening effect was studied by in vitro tyrosinase inhibition and B16F10 melanoma assay; the two cells were found to be non-cellular when the concentration of DPE was 100 ㎍/ml. Albutin concentration (positive control) in the whitening test was set at a capacity of 100 ug/ml and m-melanocyte stimulating hormone (α-MSH). A melanin-producing induction material was set at a concentration of 100 nM, and the expression of collagen type I and MMP1 collagenase was measured using HDF cells. MMP1 expression was seen to reduce in a concentration-dependent manner in treatment with DPE. Inhibiting melanin generation with B16F12 cells indicated a tendency to decrease in the DPE treatment group. Both L-Tyrosine and L-DOPA as DPE were used in an in vitro tyrosinase induction test to demonstrate the effects of tyrosinase suppression on concentrations. The higher the concentration of DPE, the greater the wrinkle reduction and whitening effect. In conclusion, it was found that DPE is an effective smoothing and whitening material by increasing collagen generation and inhibiting collagenase expression and reducing melanin production.

• Journal of Gifted/Talented Education
• /
• v.17 no.2
• /
• pp.365-391
• /
• 2007

As a previous study to investigate recognition gap of creativity between Korea and America, this study has examined Korean university students' implicit creativity toward Korea and America. The research method using in this study was as follows: The subject were university students in Korea, and they were asked to answer multiply for open-ended questions. For the analysis of the answers, a frequency analysis was used. The results were as follows: 1) It showed that Korean university students considered creativity trait as cognitive trait, personality, cultural trait, research and development areas and arts areas. This result means that Korean university students tend to recognize creativity similarly to the ways of established theories of creativity. 2) For the case of Korea, environmental trait like sociocultural background had great importance for all cases of creativity trait and non-creativity trait. 3) American creativity was recognized focused on individual tendency, on the while, community spirit was considered as creativity trait in Korean creativity. 4) It is considered that American culture had better condition for displaying creativity than Korean culture. 5) Traditional culture of Korea was recognized as creativity trait in terms of originality and superiority, and the possibility of modernistic use of Korean culture. 6) Creative people were ranked by artists, executives, rulers and scientists who were well-known to Korean university students. 7) In the comparison of creativity trait between the two countries revealed the traits of creative people, American creativity was reflected more than Korean creativity, This result seems that those people were favored by Korean university students who were familiar with American culture. In conclusion, this study has found another possibility of creativity of the East among cross-cultural creativity studies. Moreover, this study has suggested that traditional culture and tradition renewal, and values of the East are superior cultural resources which are not exist in the West, and those are expected to play a role in developing creativity.

• Journal of Sericultural and Entomological Science
• /
• no.11
• /
• pp.1-14
• /
• 1970

The following results were obtained by surveying the productivity of mulberry fields in Korea. 1. The productivity of mulberry field per 10a in which cocoon can be yield belongs to the range of 9.8∼105kg, and among them the productivity of 20 to 60kg was chiefly distributed. And their average was 50.2kg. 2. In general, the larger the mulberry field in scale per a person is, the lower the productivity of it is, but about 6.6 ares per a person was estimated to be economic scale for high productivity. 3. As far as the texture of soil is concerned, sandy-loam and loam contained a capacity of higher productivity while others like clay and sand that of lower productivity, And the depth of surface soil must be at least 50cm, although 70cm's depth of surface sail could bring about high productivity. 4. Fertilization of 900kg's compost on planting and 1,200kg's that after planting could enhance the productivity, because the use of compost have a positive relation to the productivity. 5. The greater the number of farmer's domestic animals is as a source of organic matter the higher the productivity is. 6. In the case of fertilization of 1,200kg compost, the amount of 20kg's nitrogen per 10 ares as chemical manure was best for high productivity. However, fertilization of 14.7kg's nitrogen as average amount of that, which is far below the standard amount, had been a factor to reduce the productivity of mulberry field. 7. In pruning the low-cut form resulted in high productivity, but as their shape become taller due to the lack of techniques, they were turned out to be non head pruning, thus to produce poor harvest of leaves. 8. The pure mulberry fields showed better productivity than others such as wide and narrow ridge planting and inter-crop planting. 9. As for the degree of planting density, at least 800 trees per 10 ares should be planted to increase the productivity, although the planting of 713 trees per 10 ares could be possible in case of the low stemmed pruning. 10. The hole and tranch in planting must be digged as wider and dipper as possible far the better growth of mulberry tree. 11. On the whole, varieties like NOsang and Y oung-cheun choowoo had a tendency of lower productivity.

• Journal of Technologic Dentistry
• /
• v.24 no.1
• /
• pp.51-63
• /
• 2002

The purpose of this study was to be of use for getting rid of job stress from dental technicians, by examining how much they were stressed out at work place as one of the professional medical personnels. The subjects in this study were 255 selected dental technicians who were working in the region of Taegu. The one-on-one interview was conducted from March 1 to 30, 2001, with structured questionnaire. The questionnaire sued in this study included 19 question items about the general characteristics and 29 items regarding job stress. The job stress was categorized into seven subareas based on earlier studies and considering the job situations of dental technicians: heavy workload, job conflicts, improper treatment, role and job knowledge, human relations, physical environment and personal matters. The job stress extent was measured on five-point Likert scale that is widely used in social science: one point for no stress, two for little stress, three for so-so, four for a little stress, and five for severe stress. Therefore, a higher point means a severer job stress. The reliability of the questionnaire turned out very good with Cronbach a = 0.9272. The findings of this study were as follows: 1. The general characteristics of the dental technicians investigated could be described as below: (1) By gender, 80.4% of the dental technicians were male, and 50.2%, the largest percentage, were in their 20s, followed by those in their 30s, those in their 40s, and those in their 50s in the order named. (2) The most common work place was dental technician shop(92.5%), followed by dental technology room in dental hospital or clinic and in general hospital in the order named. The primary duties were coating materials work(30.6%), followed by sculpture, grinding, partial and full denture and orthodontics in the order named. 2. The most larges (1) The most largest motivation to be a dental technician was its being a professional(33.7%), followed by the advice from others, their own aptitude, and good economic treatment in the order named. 3. Their job stress could be explained as below: (1) Their collective job stress average was 3.96$^{\circ}{\ae}$0.50 on the basis of 5 point, which showed that they were exposed to a fairly severe job stress. (2) By area, they were most stressed out from heavy workload (4.12), and they also were severely stressed from role and job knowledge(4.02) and personal matters(4.00). (3) By situation, they were most stressed when the disagreement of prosthesis that results from a specific error is unconditionally attributed to them(4.43). And they were also stressed a lot when their workload increases due to the rework(4.38), when a dentist asks something difficult for them to resolve(4.20), when heavy workload makes their working hours irregular and it's impossible to lead a personal life or have leisure time(4.16), and when they are o work for an excessively short time(4.16). This fact indicated that most of the dental technicians were exposed to a lot of stress in conjunction with job performance. 4. The main duties they took charge of didn't make any significant difference to their job stress, but yielded a significant difference to the extent of job stress in individual areas and the order of the most stressful one. Those who were engaged in grinding were most stressed from their own matters, whereas heavy workload was most stressful for those who were engaged in the other types of works. 5. As a result of seeing if their personal characteristics yielded any differences to job stress, the personal characteristics that made their job stress vary significantly were working hours, motivation of being a dental technician, job satisfaction and willingness to continue doing dental technology works. There was a tendency that longer working hours led to severer job stress, and those who chose to be a dental technician according to their own aptitude were less stressed than the others who became a dental technician because of economic reason or advices from others. And the people who were satisfied with their job were exposed to less job stress than the others who weren't, and those who had an intention to keep that job as much as possible were less stressed, compared to the others who hadn't.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.4
• /
• pp.5-11
• /
• 2014

Recently, there have been various lifeline installations constructed in the underground space of urban area due to the effective use of land. For newly installed lifelines or the management of the installed lifelines, many construction activities of excavation and backfilling are observed. Around these area, there are possibilities of collapse or excessive settlement due to the leaking of the pipe or unsatisfactory compaction of backfill material. Besides, construction costs can be saved since the on-site soils are used. The application of this liquidity filling material is not only to the lifeline installation but also to underpin the foundation under the vibrating machinery. On the evaluation of the applicability of this method to this circumstance, the strength should be investigated against the static load from the machine load as well as the vibration load from the activation of the machine. In this study, the applicability of the liquidity fill material on the foundation under the vibrating machinery is assessed via uniaxial compression and resonant column tests. The liquidity filling material consisting of the on-site soils with loess and kaolinite are tested to investigate the static and dynamic characteristics. Furthermore, the applicability of the reclaimed ash categorized as an industrial waste is evaluated for the recycle of the waste to the construction materials. The experimental results show that the shear modulus and 7 day uniaxial strength of the liquidity filling material mixed with reclaimed ash show higher than those with the on-site soils. However, the damping ratio does not show any tendency on the mixed materials.

• Journal of Korean Society of Forest Science
• /
• v.83 no.3
• /
• pp.365-371
• /
• 1994

This study was conducted to investigate variations in taxol contents of bark, shoots, needles of three native Taxus species in Korea. Sample materials were collected in early October of 1992 from five individual, trees each of the five populations of Taxus cuspidata located at Mt. Halla, Mt. Jiri, Mt. Deokyu, Mt. Sobaek, and Mt. Taebaek and two individual trees of Taxus cuspitosa in Mt. Seolak and in March of 1993 from the five individual trees of Taxus cuspidata var. latifolia in Ulleung Island. The collected materials were analyzed by HPLC to determine the amount of taxol content. Regardless of species and population, the taxol content was highest in bark and followed by shoots and needles. In Taxars cuspidata the taxol content in the bark was highest for the population of Mt. Halla (0.017%) and decreased in the order of Mt. Jiri, Mt. Sobaek, Mt. Deokyu, and Mt. Taebaek. The taxol content in the shoots was highest for the population of Mt. Halla(0.0053%) and decreased in the order of Mt. Sobaek, Mt. Jiri, Mt. Deokyu, and Mt. Taebaek. The taxol content in the needles was higher for the population of Mt. Halla(0.0013%) than any other populations and decreased in the order of Mt. Taebaek, Mt. Sobaek, Mt. Deokyu and Mt. Jiri. The taxol contents of Taxus caespitosa(0.0035%) were lower than that of Taxus cuspidate in all of the three plant parts. The taxol content of Taxus cuspidate var. latifolia(0.0064%) was higher than that of Taxus cuspidate for shoots and needles, but lower than that of Taxus cuspidate. There was a tendency of increasing taxol contents of bark and shoots of Taxus cuspidate, as latitude decreased. This study indicated that taxol content was relatively high in the populations of Taxus cuspidate. Particularly taxol content in the bark of the Taxus cuspidate in Mt. Halla population was about the same as that of pacific yew, indicating a high potential for commercial use.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.10 no.6
• /
• pp.15-26
• /
• 2015

The purpose of this study was to examine the area, theme and method of domestic articles on the successful establishment of venture companies, which were presented between 1998 and 2014, according to related basic classification criteria in an effort to shed light on the characteristics of these studies. It's basically meant to make a contribution to the development of research on the success of venture business and to be of practical use for the success of venture companies in our country. After related earlier studies were analyzed, 164 articles were collected, and 64 articles were selected from among them. The articles that were overlapped, not presented or not registered were excluded. The related studies had been conducted by different learned societies that were interested in the same research themes, and the studies were primarily led by the Korean Society of Business Venturing as of 2014, especially by Asia-Pacific Journal of Business Venturing and Entrepreneurship that was a journal published by this society. This society seemed to have taken the initiative in this field. There was a tendency that the related studies increased in number due to the shifts of modern industrial society and the changing policies of the government, as the number of the studies has been on the steady rise since 2012. In terms of method, quantitative research methods, especially descriptive studies, were prevailing. To step up the development of research into this field, a wide variety of research methods should be utilized in the future. As for the sphere of research, the characteristics of founders, strategic characteristics and environmental characteristics were mainly covered as the success factors of venture business. More diverse variables should be explored as well to make more advanced, extended research in the years to come. The findings of the study are expected to provide both theoretical and practical information on the establishment and success of venture business to make a contribution to the development of research.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.279-287
• /
• 2018

Sealants are an important element of modern architecture and serve as a building protection against weathering by providing barriers against ingress of moisture, air, and other materials. Exposure to a variety of environments often reduces lifespan due to changes in physical, chemical and mechanical characteristics, and UV, humidity, and temperature expansion are important issues that are directly related to durability. In this study, a combined deterioration test chamber was developed to simulate the environment of the open air as an instrument for verifying the durability of structural sealing materials indoors. In order to replicate special weather conditions, such as yellow dust, acid rain, and contamination by microorganisms, it was deemed impossible to replicate the outdoor environment by 100 %, and the results of the results of the results of the external exposure test of the structural sealant and the combined deterioration testing device. As a result of the displacement test of the outdoor exposure test, it was determined that the sealant was breaking apart and that it would be smooth, and the displacement would be up to three times greater than the initial material value of 1 year. The displacement test results of the combined deterioration test device show the tendency to deteriorate, decreasing the elasticity and tensile characteristics. In the case of denatured silicon, the current 400 cycles have been completed to confirm 12 months of degradation of the external exposure. The deformation of the test specimen cannot be verified with the naked eye, so it is considered that the conditions of the specimen are more stable than the silicon sealant. As a result of the outdoor exposure test, if the combined deterioration test device is structured and proposed in the relevant guidance or specification, the anticipated lifespan of 12 months in the actual use environment can be verified indoors and below 3 months later, economically.