• 한국철도학회논문집
• /
• 제5권2호
• /
• pp.55-60
• /
• 2002

This study proposes the post-processor simulator construction of ultrasonic signal for integrity evaluation of railway truck. For these purposes, the ultrasonic signals for defects(crack) of weld zone in frames are acquired in the type of time series data and echo strength. The detection of the natural defects in railway truck is performed using the characteristics of echodynamic pattern in ultrasonic signal. The constructed post-processor simulator agree fairly well with the measured results of test block(defect location, beam propagation distance, echo strength, etc). Proposed post-processor simulator construction of ultrasonic in this study can be used for the integrity evaluation of railway truck.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제3B권4호
• /
• pp.173-178
• /
• 2003

The rotational force of ultrasonic motors is able to get from the frictional force of elliptical vibration by contact between rotor and stator. Generally, ultrasonic motors are suitable for driving at resonant frequencies of about 20∼80［KHz］. The driving characteristics of ring type ultrasonic motors are the object of this study. A two-phase driving signal is delivered to the tested ultrasonic motor, which has a $90^0$ phase difference respectively with both sine and cosine voltage waveforms. The driving frequency is almost equal to the mechanical resonant frequency for the proper operation, and the driving signal is supplied by the two-phase parallel resonant inverter. The validity of the proposed driving method is verified by experimental results with stable operation.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권3호
• /
• pp.123-130
• /
• 2001

The purpose of this study is to suggest the non-destructive equation for the estimation of concrete strength by ultrasonic pulse velocity at the Age of 28day compressive strength of $600{\sim}1000kg/cm^2$. For this purpose, selected test variables were water-hinder ratio, replacement ratio of silica fume, binder content, maximum size of coarse aggregate and sand-aggregate ratio. From the results, the average increase or decrease of ultrasonic pulse velocity is 61m/sec for each 1% of moisture content. And the correlation equation between the ultrasonic pulse velocity and the compressive strength of concrete is as follows. $F_c=896.3V_p-3514$ ($R^2$ = 0.81) where, $F_c$ : compressive strength($kgf/cm^2$), $V_p$ : ultrasonic velocity(km/sec).

• Tribology and Lubricants
• /
• 제16권5호
• /
• pp.351-356
• /
• 2000

The feasibility of an ultrasonic technique using a pulse-echo method of normal-incident compressional waves was evaluated for its sensitivity to the worn surface and near surface damage due to wear. Worn surfaces were generated at various oscillation frequency under a given load and amplitude and these surface were in situ monitored using a ultrasonic wave detection system. Analysis of the ultrasonic waves received from the worn surface revealed a close relationship between the surface and near-surface damage and the maximum echo-amplitude of the compressional waves. The ultrasonic technique was successful in assessing the level of severity of the worn surface in real time during the wear process. It is also shown that the wear depth can be easily measured by the calculation of change of the specimen thickness based on the wave speed measured for the specimen medium.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.82-88
• /
• 2003

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. Recently, the ultrasonic wave has been considered as a solution fur this problem, and an ultrasonic system was constructed for the ultrasonic NDE of fruits and vegetables in our previous work. In this paper, the practical applicability of our ultrasonic system is tested fur the inspection of internal defects (central cavity) in Atlantic potato. Sound speed and RMS of transmitted ultrasonic wave signal were measured and classification algorithm using 2 dimensional stochastic analysis. was presented. Experimental results showed greater value of sound speed and RMS (root mean square) of transmitted signal in normal samples than in abnormal samples with cavity. Also a stochastic method to distinguish normal and abnormal showed fault detection rate less than 5%.

• 비파괴검사학회지
• /
• 제23권3호
• /
• pp.270-279
• /
• 2003

Parametric studies have been conducted into the variability of the factors affecting the ultrasonic testing applied to weldments. The influence of ultrasonic equipment, transducer parameters, test technique, job parameters, defect type and characteristics on reliability far defect detection and sizing was investigated by experimentation. The investigation was able to build up substantial bank of information on the reliability of manual ultrasonic method for testing weldments. The major findings of the study separate into two parts, one dealing with correlation between ultrasonic techniques, equipment and defect parameters and inspection performance effectiveness and other with human factors. Defect detection abilities are dependent on the training, experience and proficiency of the UT operators, the equipment used, the effectiveness of procedures and techniques.

• 비파괴검사학회지
• /
• 제27권6호
• /
• pp.576-581
• /
• 2007

Ultrasonic nonlinearity has been considered as a promising method to evaluate the micro damage of material; however, its magnitude is so small that its measurement is not easy. Especially, when we use contact PZT transducer, if the contacting pressure is not kept in constant during the measurement then there exists extraneous fluctuation in the measured nonlinearity caused by the unstable contact condition, In this paper, we developed a pneumatic control system to keep the contacting pressure of transducer in constant during the measurement and analyzed the effect of contacting pressure to the ultrasonic nonlinearity measurement As a result, we found that the pressure of transducer in our measurement system should be greater than 170 kPa to measure the ultrasonic nonlinear parameter in stable with no dependency on the contacting pressure.

• 수산해양교육연구
• /
• 제19권3호
• /
• pp.478-490
• /
• 2007

A technology of ultrasonic biotelemetry for tracking fish behavior is investigated. The ultrasonic biotelemetry system is constituted by a transmitter and a receiving system. Because a pinger was mainly used for the transmitter, the capability for pinger to possess was investigated and the efficient usage for pinger was examined. A source pressure level and a frequency were synthetically examined so that pinger could realize small size, a light weight, and a long life time. The receiving system is divided roughly into directional hydrophone systems and acoustic positioning systems by the receiving method. The directional hydrophone system is divided into single beam and multiple beam with the number of hydrophone, and the acoustic positioning systems is divided into LBL (Long Base Line), SBL (Short Base Line), and SSBL (Super Short Base Line) on the basis of base line. The present situation, the merits and demerits, and the principle of each receiving method were investigated in detail, and the efficient usage for each receiving method were examined.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.70-74
• /
• 1998

This paper describes a method for recognition of two-dimensional position of an object by use of aerial ultra-sonic sensor and signal processing technique, which would become a help for blind person or self-mobile robot. First, we have developed a method for measuring the time difference between the transmitted and the received burst wave by use of one ultrasonic transmitter and three receivers. Secondly, a new method is developed for measuring the distance to an object by use of M-sequence correlation method. Thirdly, a measurement method to obtain the position of an object is described by use of phase-arrayed ultrasonic sensor, which gives us a wide-range position determination in a short time.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.265-268
• /
• 2008

본 연구에서는 서로 다른 연소속도 범위를 갖는 다양한 고체추진제의 연소속도를 고압($\sim$5,000 psia)까지 측정하였고, 측정된 연소속도의 자체적인 편차를 추진제 종류별, 압력별로 분석하여 초음파법의 측정 정밀도를 평가하였다. 또한 스트랜드 버너법을 이용한 연소속도 측정값과 상호 비교하여 두 측정 기법의 특성을 비교해보았다.