• Smart Media Journal
• /
• v.4 no.2
• /
• pp.55-61
• /
• 2015

A bandwidth-enhanced ultra-wide band (UWB) CMOS balun-LNA is implemented as a part of a software defined radio (SDR) receiver which supports multi-band and multi-standard. The proposed balun-LNA is composed of a single-to-differential converter, a differential-to-single voltage summer with inductive shunt peaking, a negative feedback network, and a differential output buffer with composite common-drain (CD) and common-source (CS) amplifiers. By feeding the single-ended output of the voltage summer to the input of the LNA through a feedback network, a wideband balun-LNA exploiting negative feedback is implemented. By adopting a source follower-based inductive shunt peaking, the proposed balun-LNA achieves a wider gain bandwidth. Two LNA design examples are presented to demonstrate the usefulness of the proposed approach. The LNA I adopts the CS amplifier with a common gate common source (CGCS) balun load as the S-to-D converter for high gain and low noise figure (NF) and the LNA II uses the differential amplifier with the ac-grounded second input terminal as the S-to-D converter for high second-order input-referred intercept point (IIP2). The 3 dB gain bandwidth of the proposed balun-LNA (LNA I) is above 5 GHz and the NF is below 4 dB from 100 MHz to 5 GHz. An average power gain of 18 dB and an IIP3 of -8 ~ -2 dBm are obtained. In simulation, IIP2 of the LNA II is at least 5 dB higher than that of the LNA I with same power consumption.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.545-546
• /
• 2008

This paper presents a low power CMOS low noise amplifier for UWB applications. To reduce the power consumption, two cascode amplifiers was stacked in DC. Designed with $0.18-{\mu}m$ CMOS technology, the proposed LNA achieves 20dB flat gain, below 3dB noise figure, and the power consumption of 5.2mW from a 1.8 V supply voltage.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.670-672
• /
• 2007

An ultra-wideband low-noise amplifier is proposed with operation up to 8.2 GHz. The amplifier is fabricated with a 0.18-${\mu}m$ CMOS process and adopts a two-stage cascode architecture and a simplified Chebyshev filter for high gain, wide band, input-impedance matching, and low noise. The gain of 19.2 dB and minimum noise figure of 3.3 dB are measured over 3.4 to 8.2 GHz while consuming 17.3 mW of power. The Proposed UWB LNA achieves a measured power-gain bandwidth product of 399.4 GHz.

• Journal of electromagnetic engineering and science
• /
• v.11 no.1
• /
• pp.27-33
• /
• 2011

In this paper, we propose a high gain, current reused ultra wideband (UWB) low noise amplifier (LNA) that uses TSMC 0.18 ${\mu}m$ CMOS technology. To satisfy the wide input matching and high voltage gain requirements with low power consumption, a resistive current reused technique is utilized in the first stage. A ${\pi}$-type LC network is adopted in the second stage to achieve sufficient gain over the entire frequency band. The proposed UWB LNA has a voltage gain of 12.9~18.1 dB and a noise figure (NF) of 4.05~6.21 dB over the frequency band of interest (1~10 GHz). The total power consumption of the proposed UWB LNA is 10.1 mW from a 1.4 V supply voltage, and the chip area is $0.95{\times}0.9$ mm.

• Journal of electromagnetic engineering and science
• /
• v.8 no.1
• /
• pp.34-39
• /
• 2008

An RF front-end dual-conversion receiver for $3{\sim}5\;GHz$ MB-OFDM UWB systems is implemented in $0.18\;{\mu}m$ CMOS technology. The receiver includes a two-stage UWB LNA, an RF mixer, an IF I/Q mixer, and a frequency synthesizer. The proposed receiver adopts the dual-conversion architecture to mitigate the burden of design of the frequency synthesizer. Accordingly, the proposed frequency synthesizer generates four LO tones from only one VCO. The receiver front-end achieves power gain of 16.3 to 21 dB, NF of 7 to 7.6 dB over $3{\sim}5\;GHz$, and IIP3 of -21 dBm, while consuming 190 mW from a 1.8 V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.76-80
• /
• 2011

This paper has proposed a 3~5 GHz low-power and wideband LNA(Low Noise Amplifier), which has been implemented in a 0.18-${\mu}m$ CMOS technology. The proposed LNA has basically the noise-cancelling topology to achieve a balun-function, wideband input matching, and relative low noise figure. In addition, it has utilized a 2nd-order LC-band-pass filter(BPF) as its output load to achieve higher power gain and lower noise figure with the lowest dc power consumption among previously reported works. The proposed amplifier consumes only 3.94 mA from a 1.8 V supply voltage. The simulation results show a power gain of more than +17 dB, a noise figure of less than +4 dB, and an input IP3 of -15.5 dBm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.158-165
• /
• 2013

In this paper, a new circuit topology of an ultra-wideband (UWB) 3.1-10.6GHz CMOS low noise amplifier is presented. The proposed UWB low noise amplifier is designed utilizing RC feedback and LC filter networks which can provide good input impedance matching. In this design, the current-reused topology is adopted to reduce the power consumption and the inductor-peaking technique is applied for the purpose of bandwidth extension. The performance results of this UWB low noise amplifier simulated in $0.18-{\mu}m$ CMOS process technology exhibit a power gain of 14-14.9dB, an input matching of better than -10.8dB, gain flatness of 0.9dB, and a noise figure of 2.7-3.3dB in the frequency range of 3.1-10.6GHz. In addition, the input IP3 is -5dBm and the power consumption is 12.5mW.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.238-246
• /
• 2011

A 3-5 GHz UWB radar chip in 0.13 ${\mu}m$ CMOS process is presented in this paper. The UWB radar transceiver for surveillance and biometric applications adopts the equivalent time sampling architecture and 4-channel time interleaved samplers to relax the impractical sampling frequency and enhance the overall scanning time. The RF front end (RFFE) includes the wideband LNA and 4-way RF power splitter, and the analog signal processing part consists of the high speed track & hold (T&H) / sample & hold (S&H) and integrator. The interleaved timing clocks are generated using a delay locked loop. The UWB transmitter employs the digitally synthesized topology. The measured NF of RFFE is 9.5 dB in 3-5 GHz. And DLL timing resolution is 50 ps. The measured spectrum of UWB transmitter shows the center frequency within 3-5 GHz satisfying the FCC spectrum mask. The power consumption of receiver and transmitter are 106.5 mW and 57 mW at 1.5 V supply, respectively.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.112-116
• /
• 2005

This paper presents a broadband two-stage low noise amplifier(LNA) operating from 3 to 10 GHz, designed with 0.18 ${\mu}m$ RF CMOS technology, The cascode feedback topology and broadband matching technique are used to achieve broadband performance and input/output matching characteristics. The proposed UWB LNA results in the low noise figure(NF) of 3.4 dB, input/output return loss($S_{11}/S_{22}$) of lower than -10 dB, and power gain of 14.5 dB with gain flatness of $\pm$1 -dB within the required bandwidth. The input-referred third-order intercept point($IIP_3$) and the input-referred 1-dB compression point($P_{ldB}$) are -7 dBm and -17 dBm, respectively.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.176-181
• /
• 2013

This paper presents a CMOS impulse radio ultra-wideband (IR-UWB) receiver implemented using IBM 0.13um CMOS technology for inner/inter-chip wireless interconnection. The IR-UWB receiver is based on the non-coherent architecture which removes the complexity of RF architecture (such as DLL or PLL) and reduces power consumption. The receiver consists of three blocks: a low noise amplifier (LNA) with active balun, a correlator, and a comparator. Simulation results show the die area of the IR-UWB receiver of 0.2mm2, a power gain (S21) of 12.5dB, a noise figure (NF) of 3.05dB, an input return loss (S11) of less than -16.5dB, a conversion gain of 18dB, a NFDSB of 22. The receiver exhibits a third order intercept point (IIP3) of -1.3dBm and consumes 22.9mW of power on the 1.4V power supply.