• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.104.2-104.2
• /
• 2013

A residual gas analyzer (RGA) system has been developed in this laboratory. Characteristics of the RGA system parts such as ion source, quadrupole mass filter and sensitivity are introduced. Some efforts have been made to improve performance of the two types of ion sources, open ion source (OIS) and closed ion source (CIS). A metal mesh was placed onto the electron beam entrance of the CIS anode tube to block the filament field penetration. Sensitivity of the CIS ion sources with and without the mesh was compared by mass spectra of SF6 gas (97% He base) introduced into the CIS anode through a needle valve. About ten-times improvement in the RGA sensitivity was observed for the CIS with the mesh in the electron entrance. Computer simulation showed an axi-symmetric anode potential distribution and improved focusing of the electron beam inside the anode tube with the mesh.

• Korean Journal of Mathematics
• /
• 제31권4호
• /
• pp.405-417
• /
• 2023

The RIP of rings was introduced by Kwak and Lee as a generalization of the one-sided idempotent-reflexivity property. In this study, we focus on rings in which all one-sided semicentral idempotents are central, and we refer to them as quasi-Abelian rings, extending the concept introduced by RIP. We establish that quasi-Abelianity extends to various types of rings, including polynomial rings, power series rings, Laurent series rings, matrices, and certain subrings of triangular matrix rings. Furthermore, we provide comprehensive proofs for several results that hold for RIP and are also satisfied by the quasi-Abelian property. Additionally, we investigate the structural properties of minimal non-Abelian quasi-Abelian rings.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1997년도 심포지움시리즈 Jan-97 수처리용 분리막 기술 및 응용
• /
• pp.87-109
• /
• 1997

Reverse osmosis(R/O), ultrafiltration(UF) and microfiltration (MF) processes are widely used for water treatment. In the seminar, characteristics of typical membrane modules including tubular, hollow fiber, plate and frame and spiral wound types will be discussed in detail. The design methods based on hydrodynamics for hollow fiber and spiral wound modules will be introduced analytically. Concentration polarization (CP) and membrane fouling mechnism as well as the techniques for CP reduction will be handled. The CP control techniques contain chemically modified membrane surface, pretreatment of feed water, operation of low trans-membrane pressure, chemical or physical cleaning methods and artificial production of various fluid turbulences near the membrane surface, etc. In especially, the recent commercial membrane modules for CP control including module rotation, vibration and Taylor or Dean vortex system will be introduced and discussed in detail.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.245-250
• /
• 2002

In this paper we presented numerical method for the simulation of powder injection molding filling process, which is one of the key processes in powder injection molding. Rheological properties of powder binder mixture such as slip phenomena and yield stress were introduced into the numerical analysis model of powder injection molding filling simulation. Numerical model can be classified into two types. One is 2.5D model which can be introduced to a arbitrary thin geometry and the other is full 3D model which can be applied to a general 3D shape. For 2.5D model we showed the validity of our CAE system with several verification examples. Finally we suggested flow analysis model for 3D powder injection molding filling simulation.

• Nonlinear Functional Analysis and Applications
• /
• 제28권1호
• /
• pp.123-134
• /
• 2023

Since Knaster, Kuratowski, and Mazurkiewicz established their KKM theorem in 1929, it was first applied to topological vector spaces mainly by Fan and Granas. Later it was extended to convex spaces by Lassonde and to extensions of c-spaces by Horvath. In 1992, such study was called the KKM theory by ourselves. Then the theory was extended to generalized convex spaces or G-convex spaces. Motivated by such spaces, there have appeared several particular types of artificial spaces. In 2006 we introduced abstract convex spaces which contain all existing spaces appeared in the KKM theory. Later in 2014-2020, Khahn and Quan introduced "topologically based existence theorems" and the so-called KKM structure. In the present paper, we show that their structure is a particular type of already known KKM spaces.

• 한국소음진동공학회논문집
• /
• 제14권4호
• /
• pp.287-294
• /
• 2004

Dynamic Load/unload (L/UL) mechanism is an alternative to the contact start stop (CSS) technology which eliminates striction and wear failure modes associated with CSS. Inertia latch mechanism becomes important for mobile disk drives because of non operating shock performance. Various types of latch designs have been introduced in hard disk drives to limit a rotary actuator from sudden uncontrolled motion. In this paper, a single spring inertia latch is introduced for a small form optical disk drive, which uses a rotary actuator for moving an optical pick-up. A new small inertia latch with sin91e spring is designed to ensure both feasible and small size. The shock performance of the new inertia latch is experimentally verified.

• 한국소음진동공학회논문집
• /
• 제18권5호
• /
• pp.503-508
• /
• 2008

In this paper, various methods to improve the planetary gear noise in vehicles were introduced. Those cases of improvement have been used as good guidelines and references to prevent planetary noise problems. In this research, different types of planetary gear systems were also analyzed. The consequences of those analysis said in common that the planetary gear set generating noise mainly is the one which takes power directly from the turbine. Furthermore, a frequency versus vibration level map was introduced to judge how to solve the noise problem quickly in a vehicle development process. Besides, it is provided a predicting method which planetary gear set most contributes to noise problem taking in the vehicle and how to design the planetary gear set robustly.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 말뚝기초 학술발표회
• /
• pp.107-141
• /
• 2000

Large diameter piles can be defined as piles with diameter of at least 0.76 m (2.5 ft). In bridge foundation, large diameter piles have been used as pier foundations and their use has been increased greatly. In this study, static pile load tests for large diameter piles peformed in Kwangan Grande Bridge construction site were introduced. Also, various sensor installation methods for several types of piles (that is, open-ended steel pipe pile, drilled shafts and socketed pipe piles), pipe axial load measuring method, load transfer analysis method and pile load test results (pile-head load - settlement curve, and pile axial load distribution curve along the pile depth) were introduced.

• Applied Science and Convergence Technology
• /
• 제24권4호
• /
• pp.77-83
• /
• 2015

Many welding processes are performed to construct cryogenic system. Leak-tight for the cryogenic system is required at low temperature environment. Helium leak detection techniques are commonly used to find leak for the cryogenic system. The helium leak detection techniques for spraying, sniffing and pressurizing techniques are introduced. High vacuum is also necessary to use helium leak detector. So, types of fluid flow, effective temperature, conductance and pumping speed are introduced for vacuum pumping. Leak test procedure is shown for pipe welding, cryomodule and low temperature test. Cryogenic seals which include copper gasket, helicoflex gasket and indium are investigated.

• 대한치과보철학회지
• /
• 제23권1호
• /
• pp.155-164
• /
• 1985

Acrylic resin has some disadvantages in its physical properties such as a low surface hardness, being easily abraded as well as low degree of impact resistance. To overcome these disavantages, Perma Cure System was introduced in 1981, in which photo polymerizing monomers coated on acrylic resin surface were polymerized. In this study, to observe the effect of Perma Cure System on physical properties of treated surface of different types of acrylic resin, abrasion resistance, surface hardness and surface roughness of 4 different types of resin (Premium, Ortho-jet acrylic, Quick resin, Thermo jel) were tested before and after coating treatment. The conclusions arised from this study are as follows; 1. In all types of resin, the abrasion resistance of coated specimen was higher than that of uncoated specimen, and there was difference in amount of abrasion among the types of coated resin. 2. In all types of resin, the surface hardness of coated specimen was higher than that of uncoated specimen, and there was no difference in surface hardness among the types of coated resin. 3. In all types of resin, surface roughness of coated specimen was lower than that of uncoated specimen, and was different according to the degree of surface roughness before coating treatment in same sort of resin specimen.