• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.161-171
• /
• 2016

OBJECTIVES : Many roadway departure crashes on the freeway interchange are due to the running speed being greater than the design speed. This study aims to ensure a safe and pleasant driving experience for the driver by increasing the superelevation based on the running speed on the highway interchange ramp. METHODS : The mean running speed for each type of ramp is calculated on site survey more than 10 interchanges. Using the mean running speed, we calculated the superelevation and the side friction using the method given in "A Policy on Geometric Design of Highways and Street" (Pages 145-166, 2001). Then, we applied the modified method to the superelevation range. Finally, we ensured safety using the Degree of Safety that is proven by the centrifugal acceleration ratio as suggested by Joseph Craus (1978). RESULTS : The mean running speeds are 50 km/h and 65 km/h when the design speeds are 40 km/h and 50 km/h, respectively. After the application of the new method used in this study, the superelevation will be increased by 9.0% and 10.0% when the mean running speeds are 50 km/h and 65 km/h, respectively. CONCLUSIONS : A higher superelevation can give the driver a more comfortable and safe driving environment. However, the driver needs to be aware of snow and low-temperature conditions.

• Journal of Bio-Environment Control
• /
• v.14 no.1
• /
• pp.7-14
• /
• 2005

This study was conducted to develop a chain conveyor-type, row-spacing system for a plant factory. The developed system was evaluated for its practical use in growing plants. Results are intended to provide technical suggestions on the row spacing for hydroponically grown vegetables in a plant factory. The designed row-spacing system for a plant factory could be adjusted by four stages with a conveying speed range of $5.3\~15.8cm{\cdot}s^{-1}$ and with a row-space range of 10-25cm. The torque of driving shaft was measured with a torque range of 11.7-33.3 N$\cdot$m according as a trough weight changes with a range of $17\~935$ N. A measured value was $5.9\~9.8\;N{\cdot}m$ lower than a theoretical value. Travel reduction rate was shown up $1.6\~1.9\%$. The conveying time of trough was shown up 2.24 seconds in case that the designed value was 2.26 seconds. The system was evaluated to be functioning effectively according to the initial design factors in the test.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.9
• /
• pp.13-20
• /
• 2022

It's proposed and analyzed ML(Machine Learning) models to predict vehicle FC(Fuel Consumption) in real-time. The test driving was done for a car to measure vehicle speed, acceleration, road gradient and FC for training dataset. The various ML models were trained with feature data of speed, acceleration and road-gradient for target FC. There are two kind of ML models and one is regression type of linear regression and k-nearest neighbors regression and the other is classification type of k-nearest neighbors classifier, logistic regression, decision tree, random forest and gradient boosting in the study. The prediction accuracy is low in range of 0.5 ~ 0.6 for real-time FC and the classification type is more accurate than the regression ones. The prediction error for total FC has very low value of about 0.2 ~ 2.0% and regression models are more accurate than classification ones. It's for the coefficient of determination (R²) of accuracy score distributing predicted values along mean of targets as the coefficient decreases. Therefore regression models are good for total FC and classification ones are proper for real-time FC prediction.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.195-203
• /
• 2005

Recently, a novel multi-bit nonvolatile memory based on double gate (DG) MOSFET is proposed to overcome the short channel effects and to increase the memory density. We need more complex voltage schemes for DG MOSFET devices. In view of peripheral circuits driving memory cells, one should consider various voltage sources used for several operations. It is one of the key issues to minimize the number of voltage sources. This criterion needs more caution in considering a DG nonvolatile memory cell that inevitably requires more number of events for voltage sources. Therefore figuring out the permissible range of operating bias should be preceded for reliable operation. We found that reliable operation largely depends on the depletion conditions of the silicon channel according to charge amount stored in the floating gates and the negative control gate voltages applied for read operation. We used Silvaco Atlas, a 2D numerical simulation tool as the device simulator.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.67-72
• /
• 2006

Blower as an air supply system is one of the most important BOP (Balance of Plant) system fur FCV(Fuel Cell Vehicle). For generating and blowing compressed air, the motor of air blower consumes maximum 25% of net power and fuel cell demands a clean air. Considering the efficiency of whole FCV, low friction lubrication of high speed rotor is needed. For the purpose of reducing electrical power and supplying clean air to Fuel cell, oil-free air foil bearings are applied at the each side of brushless motor (BLDC) as journal bearings which diameter is 50mm. The normal power of driving motor has 1.7kW with the 30,000rpm operating range and the flow rate of air has maximum 160 SCFM. The impeller of blower was adopted a mixed type of centrifugal and axial which has several advantages for variable operating condition. The performance of turbo-blower and parameters of air foil bearings was investigated analytically and experimentally. From this study, the performance of the blower was confirmed to be suitable far 80kw PEM FC.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.1-8
• /
• 2000

For the purpose of a cost effective design of practical subsoni $c^ersonic ejector systems, an experiment was carried out using a superheated steam as a primary driving flow. The superheated steam jet was produced by several different kinds of subsonic and supersonic nozzles. The secondary flow of atmospheric air inside a plenum chamber was drawn into the primary steam jet. The vacuum performance of the plenum chamber was investigated for a wide range of the ejector operation pressure ratio. The result showed that the static pressure of the mixed flow at the ejector throat is only a function of the ejector operation pressure ratio, regardless of the primary nozzle type employed.ed.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.297-304
• /
• 2009

This study was conducted to investigate the adequacy of the representative empirical models which are developed for predicting the tractive performance of the tractor operating in various soil conditions. Four representative empirical models which are widely used in the traction prediction of tractor were selected through literature review. Four models were Wismer-Luth, Brixius, Dwyer and Hernandez model, which were empirical traction models of a single wheel. The efficacy of four models were confirmed via comparison of the tractions of tractor predicted using the four models with those measured from traction tests which were conducted for two different driving type (2WD and 4WD) of the tractor on two different soil conditions. The results showed that tractions predicted by Brixius' model, especially for slip range under 20% which the operating efficiency of a tractor is very high, were well consistent with the ones measured from traction test better than the tractions predicted by models which are proposed by Wismer-Luth, Dwyer and Hernandez.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.396-401
• /
• 2001

Heat transfer analysis of a iron core type linear motor for surface mounting device applications was considered in this study. In order to avoid the complex conjugate problem a fluid flow regime and a solid regime were considered separately. First, film coefficients of the moving parts were evaluated from computational fluid dynamic analysis and those of the stationary parts from the existing empirical or analytic correlations. And then, by applying them, internal and external temperatures of the linear motor pal1s were computed through finite element analysis. Both computation and measurement were carried out with respect to motor driving power. The measurement did not exhibit a linear temperature variation trend with respect to motor power while the computation revealed a linear correlation. Nonetheless, the computations agreed with the measurements within an error range of 20%. It indicates that an adequate heat transfer model for the reciprocative coil assembly may help more exact prediction.

• Journal of Power Electronics
• /
• v.11 no.4
• /
• pp.471-478
• /
• 2011

This paper addresses the establishment of a kVA-range plug-in hybrid electrical vehicle (PHEV) integration test platform and associated issues. Advancements in battery and power electronic technology, hybrid vehicles are becoming increasingly dependent on the electrical energy provided by the batteries. Minimal or no support by the internal combustion engine may result in the vehicle being occasionally unable to recharge the batteries during highly dynamic driving that occurs in urban areas. The inability to sustain its own energy source creates a situation where the vehicle must connect to the electrical grid in order to recharge its batteries. The effects of a large penetration of electric vehicles connected into the grid are still relatively unknown. This paper presents a novel methodology that will be utilized to study the effects of PHEV charging at the sub-transmission level. The proposed test platform utilizes the power hardware-in-the-loop (PHIL) concept in conjunction with high-fidelity PHEV energy system simulation models. The battery, in particular, is simulated utilizing a real-time digital simulator ($RTDS^{TM}$) which generates appropriate control commands to a power electronics-based voltage amplifier that interfaces via a LC-LC-type filter to a power grid. In addition, the PHEV impact is evaluated via another power electronic converter controlled through $dSPACE^{TM}$, a rapid control systems prototyping software.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.311-319
• /
• 2018

Purpose: The aim of this study is to develop a small combine for harvesting miscellaneous cereal crops. Methods: A prototype small combine was designed and constructed. Its specifications and basic performance were investigated. Results: The prototype small combine for harvesting miscellaneous cereal crops was designed and constructed to reflect similar specifications as those of the conventional combine. The prototype small combine comprises a diesel engine with the rated power/speed of 22.0 kW/2,600 rpm, three-stage primary and two-stage speed range transmission shifts, and a double acting threshing part. The maximum travel speeds of the prototype combine are approximately 0.72 m/s, 2.50 m/s, 0.30 m/s at the low, high speed range shifts in the forward direction, and while traversing in the reverse direction, respectively. The minimum radius of turning was approximately 1.50 m. In a static lateral overturning test, the prototype combine overturned neither to the right nor to left on a $30^{\circ}$ slope. The results of an oilseed rape harvesting test included the maximum operating speed of 0.32 m/s, the grain loss ratio of approximately 9.0%, and the effective field capacity of approximately 10.3 a/h. Additionally, among the outputs in grain outlet, the whole grains, damage grains, and materials other than grain (MOG) ratios accounted for 97.4%, 0.0%, and 2.6%, respectively. Conclusions: The prototype small combine for harvesting miscellaneous cereal crops indicates good driving ability and stability. The results of the oilseed rape harvesting test reveal that the harvesting performance must be enhanced such that the separating and cleaning parts are more suitable for each type of crop, thus reducing grain loss and foreign substances among the outputs in grain outlet. An improved small prototype combine could be used effectively to mechanize the harvesting of miscellaneous cereal crops in small family farms or semi-mountainous areas.