• Journal of the Korean Society of Groundwater Environment
• /
• v.6 no.2
• /
• pp.95-100
• /
• 1999

Hydrocarbon compounds in vadose zone soils caused by adsorption onto the surfaces of solid particles are generally considered to show retardation effect. In this study, we investigated the retardation effect on the transport of Benzene in a sandy soil by conducting batch and column tests. The batch test was conducted by equilibrating dry soil mass with Benzene solutions of various initial concentrations. and by analyzing the concentrations of Benzene in initial and equilibrated solutions using HPLC. The column test consisted of monitoring the concentrations of effluent versus time known as a breakthrough curve (BTC). We used KCl and Benzene solutions with the concentration of 10 g/L and 0.88 g/L as a tracer, and injected them into the inlet boundary of the soil sample as a square pulse type respectively, and monitored the effluent concentrations at the exit boundary under a steady state condition using an EC-meter and HPLC. From the batch test, we obtained a distribution coefficient assuming that a linear adsorption isotherm exists and calculated the retardation factor based on the bulk density and porosity of the column sample. We also predicted the column BTC curve using the retardation factor obtained from the distribution coefficient and compared with the measured BTC of Benzene. The results of the column test showed that i) the peak concentration of Benzene was much smaller than that of KCl and ⅱ) the travel times of peak concentrations for the two tracers were more or less identical. These results indicate that adsorption of Benzene onto the sand panicles occurred during the pulse propagation but the retardation of Benzene caused by adsorption was not present in the studied soil. Comparison of the predicted with the measured BTC of Benzene resulted in a poor agreement due to the absence of the retardation phenomenon. The only way to describe the absolute decrease of Benzene concentration in the column leaching experiment was to introduce a decay or sink coefficient in the convection-dispersion equation (CDE) model to account for an irreversible sorption of Benzene in the aqueous phase.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1319-1330
• /
• 2000

Activated carbons prepared by chemical activation of organic waste sludges with $ZnCl_2$ and $K_2S$ have been studied in terms of their pore development and adsorptivity. Pore development of the carbons prepared from organic waste sludges was characterized by the nitrogen adsorption at 77K. The $ZnCl_2$-activated carbon produced by chemical activation with zinc chloride exhibited type I isotherm characteristics according to the BDDT classification, suggesting the presence of micropores formed by activation process. The isotherms of the commercial powdered activated carbon and $K_2S$-activated carbon reveal a hysteresis similar to that of type IV in BDDT classification, indicating the formation of mesopores. This result implies that the major pores of $K_2S$-activated carbon are composed of meso and micropores, and a macropores are minor. The adsorptive capacities of metal on the $K_2S$-activated carbon prepared from organic waste sludges were found to be superior to those on a commercial granular activated carbon. The Langmuir and Freundlich isotherms yield a fairly good fit to the adsorption data, indicating a monolayer adsorption of metals onto $K_2S$-activated carbon. The adsorptive capacity of the $K_2S$-activated carbon was superior to $ZnCl_2$-activated carbon for $PO_4$-P, and vice versa for $NO_3$-N. From the results of the studies reported here, it can be concluded that activated carbons with adsorptivity superior to commercial granular activated carbons can be produced from organic waste sludge using a two-step carbonization/activation procedure with zinc chloride or potassium sulfide as the activating agents.

• Journal of the Korean Chemical Society
• /
• v.52 no.2
• /
• pp.124-132
• /
• 2008

effect of some furfural hydrazone derivatives (I -V) as corrosion inhibitors for C-steel in 3M H3PO4 solution in which M indicates mol/l has been studied using weight-loss and galvanostatic polarization techniques. A significant decrease in the corrosion rate of C-steel was observed in the presence of the investigated compounds. This study revealed that, the inhibition efficiency increases with increasing the inhibitor concentration, and the addition of iodide and thiocynate ions enhances it to a considerable extent. The effect of temperature on the corrosion behavior of C-steel was studied in the range from 30-60oC with and without 510-6 M investigated compounds using weight-loss method. Apparent activation corrosion energy (Ea*) and other thermodynamic parameters for the corrosion process were calculated and discussed. The polarization measurements show that the investigated compounds act as mixed-type inhibitors, but the cathode is more polarized when an external current was applied. The adsorption of these compounds on the surface of C-steel in 3M H3PO4 obeys Frumkins adsorption isotherm. The mechanism of inhibition was discussed in the light of the chemical structure of the investigated compounds.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.7
• /
• pp.1097-1103
• /
• 2007

We report a novel method to synthesize nanocomposites composed of titania nanoparticles and phosphotungstate ions with various composition ratios ranging from W/Ti = 12/10 to 12/500 by inducing the electrostatic interaction between the positively charged protonated titania sol-particles and the negatively charged phosphotungstate anions to flocculate and precipitate. The precipitates showed varied features depending on the composition. The precipitate from the tungsten-richest W/Ti = 12/10 reaction is amorphous in its powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and Raman spectroscopy data. This material shows the Type II adsorption characteristics in its N2-adsorption isotherm, but with quite low surface area of 34 m2/g. To the contrary, the precipitates from the titanium-richer reactions (W/Ti = 12/50- 12/500) are composed of anatase nanoparticles of 2-6 nm by XRD, TEM and Raman and show the Type I adsorption characteristics. The surface area linearly increases with the titanium content from 131 m2/g for W/ Ti = 12/50 to 228 m2/g for 12/500. The precipitate from the reaction with the intermediate composition W/Ti = 12/20 is composed of anatase nanoparticles and does not have any pore accessible to N2. With the wide variety of the physical properties of the precipitates, the present method can be a novel, viable means to tailor synthesis of nanocomposite materials. A formation mechanism of the precipitates is based on the electrostatic interactions between the titania nanoparticles and phosphotungstate ions.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.370-374
• /
• 2013

The effects of zinc chloride addition on pore development of porous carbon nanofibers prepared by polyacrylonitrile (PAN)/ N,N'-dimethylformamide (DMF) (10 wt%) electrospinning were investigated. The change of morphological and structural modification by zinc chloride activation was investigated by a scanning electron microscopy (SEM) analysis. $N_2$ adsorption isotherm characteristics at 77 K were confirmed by Brunauer-Emmett-Teller (BET) and Horvath-Kawazoe (H-K) equations, and the curves showed the Type I mode in the International Union of Pore and Applied Chemistry (IUPAC) classification, indicating that lots of micropores exist in the sample. In addition, specific surface areas and total pore volumes of porous carbons prepared by the zinc chloride activation were determined as 600~980 $m^2/g$ and 0.24~0.40 $cm^3/g$, respectively. As experimental results, many holes or demolished structures were found on the fiber surfaces after the zinc chloride activation as confirmed by a SEM analysis. It was also observed that various pore sizes were found to be depended on the adding content of zinc chloride in PAN/DMF solution in this system.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.204-210
• /
• 1997

Zeolite 4A-impregnated complex molecular sieve was prepared by hydrothermal reaction after aluminosilicate gel was penetrated into the pore of activated carbon granule. The crystals of zeolite 4A mainly were formed in the macropore of activated carbon, and their average diameter is $0.8{\mu}m$. The pore volume of activated carbon granule is $0.67m{\ell}/g$, and the pore volume of the sample including 21.6wt% of zeolite 4A crystal is $0.41m{\ell}/g$ decreasing the pore volume by 40% due to the crystallization of zeolite 4A crystals on the internal surface of activated carbon. The calcium ion exchange capacity of zeolite 4A-impregnated sample is 320mg $CaCO_3/g$ zeolite, and this value is almost the same as that of zeolite 4A powder. The crystal of zeolite 4A was not separated from the support of activated carbon granule in the course of ultrasonic dispersion. The adsorption isotherm of water on zeolite 4A-impregnated sample shows the intermediate shape between types, I and III. In addition, zeolite 4A-impregnated sample shows the hydrophilic and hydrophobic properties simultaneously.

• Nuclear Engineering and Technology
• /
• v.16 no.2
• /
• pp.64-69
• /
• 1984

With regard to the radioactive waste disposal, adsorption properties and migration rates have been evaluated for Cs-137 and Sr-90 with the domestic clay sampled from Cnyang, Sanchong and Mooan. Sorption coefficients (Ksorp) were determined by batch experiments. The measured values of Ksorp were ranged from 8000 to 17,000 ml/gr for Cs-137 of 0.1$\mu$Ci/ml, and from 10,000 to 15,000m1/gr for Sr-90 of 0.l$\mu$Ci/ml. Remarkably, Mooan clay showed lower values of Ksorp than those of the others. This could be explained by the poor soprtion capacity of the quartz found only in the Mooan clay. For the quantitative analysis, sorption isotherm equations of Freundlich type were made with the obtained values of Ksorp. $C_{R}$=18.0 $C_{A}$$^{0.74}$ : Cs-137, $C_{R}$=0.84 $C_{A}$$^{0.45}$ : Sr-90. By introducing the BOX model combined with the above relationships, simulation of underground nuclide movement was carried out. The results showed that the domestic clays could be the effective backfill material for repositories.itories.ies.

• Corrosion Science and Technology
• /
• v.12 no.2
• /
• pp.65-78
• /
• 2013

The present investigation deals with the corrosion inhibition of mild steel in 1M $H_2SO_4$ with 1, 4-dihydro pyridine and its derivatives prepared using microwave activation method. The synthesis of inhibitor was confirmed by IR spectra. The effect of 1, 4-dihydropyridine derivatives on the corrosion inhibition of mild steel in 1M $H_2SO_4$ was studied using weight loss and electrochemical polarization techniques. Influence of temperature (303-333K) and synergistic effect of halide ions ($I^-$, $Br^-$ and $Cl^-$) on the inhibition behaviour was also studied. Corrosion products on the metal surface were analyzed by scanning electron microscopy (SEM) and a possible mechanism of inhibition by the compounds is suggested. Thermodynamic parameters were calculated using weight loss data in order to elaborate the mechanism of corrosion inhibition. Polarization measurements revealed that the studied compounds acted as mixed type inhibitor but slightly anodic in nature. Electrochemical impedance measurements revealed that the compounds were adsorbed onto the carbon steel surface and the adsorption obeyed the Langmuir adsorption isotherm. The synergistic effect of halide ions on the IE increases with increase in concentration. The IE obtained from atomic absorption spectrophotometric studies was found to be in good agreement with that obtained from the conventional weight loss method. SEM revealed the information of a smooth, dense protective layer in presence of the inhibitors.

• Korean Journal of Environmental Agriculture
• /
• v.3 no.1
• /
• pp.22-29
• /
• 1984

The Freundlich-type adsorption isotherms were obtained in this study on the adsorption of linuron, bentazon, trifluralin and butachlor by soils. A strong correlation was shown between soil organic matter content and the adsorption of linuron. Soils with high organic matter content adsorbed more linuron. There was no significant correlation between the adsorption of bentazon and clay content. There was a tendency that increase in organic matter content acts against the adsorption of bentazon. Repulsive forces seemed to exist between negatively charged soil particle surfaces and betazon molecules which become weakly charged negative ions in soil solution. Organic matter content and cation exchange capacity appeared to be enhancing the adsorption of trifluralin and butachlor. Clay content was not significantly correlated with the adsorption of these herbicides. Trifluralin was adsorptive to the greatest extent, followed by linuron and butachlor, bentazon being the least.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.70-84
• /
• 2008

A series of the studies on the applied physical properties of domestic species have been conducted last three years. Pinus densiflora was one of the three species examined for the first year. Because the same apparatus and experimental procedures were used for all species, their results can be easily comparable. The experiments for sorption property were conducted with 20- and 80-mesh wood powder and resulted in their EMC's and sorption isotherms at various heating conditions. The thermal conductivity and diffusivity, and electric resistance and volumetric electric resistivity were measured with a thermal-wire device and a high electric resistance meter. The differences of the thermal and electric properties between quarter- and flat-sawn specimens were observed, which was partially attributed to their anatomical differences. An acoustic measurement system was used to evaluate dynamic MOE and internal friction. This paper provides the useful fundamental data for designing a wood structure, correcting a portable resistance-type moisture meter, and nondestructive testing wood.