• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.423-424
• /
• 2011

This paper has proposed a 920 MHz RF front-end for IEEE 802.15.4g SUN (Smart Utility Network) systems. The proposed 920 MHz RF front-end consists of a driver amplifier, a low noise amplifier, and a RF switch. In the TX mode, the driver amplifier has been designed as a single-ended topology to remove a transformer which causes a loss of the output power from the driver amplifier. In addition, a RF switch is located in the RX path not the TX path. In the RX mode, the proposed low noise amplifier can provide a differential output signal when a single-ended input signal has been applied to. A LC resonant circuit is used as both a load of the drive amplifier and a input matching circuit of the low noise amplifier, reducing the chip area. The proposed 920 MHz RF Front-end has been implemented in a 0.18-um CMOS technology. It consumes 3.6 mA in driver amplifier and 3.1 mA in low noise amplifier from a 1.8 V supply voltage.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.207-214
• /
• 2005

This paper presents a channel structure for promising high performance pseudomorphic high electron mobility transistor(pHEMT) switching device for design and fabricating of microwave control circuits, such as switches, phase shifters, attenuators, limiters, for application in personal mobile communication systems. Using the designed epitaxial channel layer structure and ETRI's $0.5\mu$m pHEMT switch process, single pole double throw (SPDT) Tx/Rx monolithic microwave integrated circuit (MMIC) switch was fabricated for 2.4 GHz and 5 GHz band wireless local area network (WLAN) systems. The SPDT switch exhibits a low insertion loss of 0.849 dB, high isolation of 32.638 dB, return loss of 11.006 dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V These performances are enough for an application to 5 GHz band WLAN systems.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.3
• /
• pp.53-63
• /
• 2006

The general objective of this study was to investigate biomechanical characteristics of bowling swing using three-dimensional cinematography. This study focused specifically on movements of the upper body segments during a bowling swing. Eight elite female bowling players participated in this study. Subjects performed bowling swing and their performance was sampled at 60 frame/sec using two high-speed video cameras with a synchronizer. After digitizing images from two cameras, the two-dimensional coordinates were used to produce three-dimensional coordinates of the 12 body segments (20 joint reference makers). The obtained three-dimensional coordinates were fed to a custom-written kinematic and kinetic analyses program (LabView 6.1, National Instrument, Austin, TX, USA). The analyses determined the linear and angular kinematic variables of the body segments with which joint force and torque of the lower and upper trunks and the shoulder were estimated based on the Newton-Euler equations. It was found that during the bowling swing the peak linear velocities of the body segments were reached in sequence the trunk, the shoulder, the elbow, the wrist, and the bowl. This result indicates that linear momentum of the lower body and the trunk transmits to the arm segment during the bowling swing. The joint torques of the torso and the arm occurred almost simultaneously, indicating that bowling swing seem to be a push-like motion, rather than a proximal-distal sequence motion in which many of throwing motions are categorized. The ultimate objective of the bowling swing is to release a heavy-weight bowl with power and consistency. Therefore, the bowling swing observed in this study well agrees with that bowlers use the stepping to increase the linear velocity of the bowl, the simple pendulum system and the push-like segmental motion in the torso and the arm segment to enhance the power at the release of the bowl.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.3
• /
• pp.1-9
• /
• 2003

In this paper, we designed a highly suppressed sidelobe ladder type RF SAW bandpass filter based on 1-port resonator, for 800 MHz mobile communication system. In order to get the highest device characteristics, we optimized some important parameters such as the electrode thickness, electrode lambda weghting of the reflectors, and static capacitance ratio. Furthermore, we fabricated the Tx and Rx. filter using optimized parameters. Implemented filters can be used in 800 MHz mobile communication system and external impedance matching circuits are not needed. RF filter was fabricated on 36$^{\circ}$LiTaO$_3$ substrates with Al-Cu (W 3 %)and mounted 3.8mm$\times$3.8mm$\times$1.5mm SMD package. Developed filters has 2.3 dB insertion loss in the 25 MHz pass-band, 33MHz with 3-dB insertion loss, stop-band rejection of 30 dB, passband ripple is less than 0.5 The power durability of the filters measured about 3.5W and the maximum temperature variation within -2$0^{\circ}C$~8$0^{\circ}C$ was 0.09 dB/$^{\circ}C$ of 3-dB insertion loss.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.1-6
• /
• 2011

This paper describes a phase modulation I/O (PMIO) serial interface circuit that supports 1Gbps transfer rate with 12mW power consumption at 1.2V supply. The proposed PMIO which consists of TX and RX blocks utilizes a phase modulation technique. The rising edge is fixed to get the clock phase information and falling edge has multi positions for the multi-data information to increase the transfer rate. The designed circuit use the 16 possible falling edge positions. The data transfer rate is four times faster than the clock rate. The circuit has been implemented using $0.13{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of transfer data (phase data) and recovery data.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.487-495
• /
• 2022

This paper describes the design and development of a high-power transmit receive module(TRM) for mounting on X-band synthetic aperture radar(SAR) of the NEXTSat-2. The TRM generates a high-power pulse signal with a bandwidth of 100 MHz in the target frequency range of X-band and amplifies a low-noise on the received signal. Tx. path of the TRM has output signal level of more than 200 watts (53.01 dB), pulse droop of 0.35 dB, signal strength change of 0.04 dB during transmission signal output, and phase change of 1.7 ˚. Rx. path has noise figure of 3.99 dB and gain of 37.38 ~ 37.46 dB. It was confirmed the TRM satisfies all requirements. The TRM mounted on the NEXTSat-2 flight model(FM) which will be launched using the KSLV-II (Nuri).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.933-940
• /
• 2017

A wireless power transfer system with a negative impedance converter(NIC) was designed and tested. The system was investigated to identify the effects of ferrites and conductors. To improve the power transfer efficiency(PTE), the Q-factor of the transmitter was enhanced by the negative resistance generated by the NIC. The NIC was composed of an Op-Amp and resistors. The negative resistance was obtained with respect to a resistor connected in a feedback loop. The dimension of the Tx coil was $250mm{\times}250mm{\times}0.8mm$. The impedance and Q-factor were $31+j1874{\Omega}$ and 60, respectively. The negative resistance was selected to be $30{\Omega}$, and the Q-factor was increased to 900 by reduction of the transmitter resistance, which was about 15 times higher than that of a conventional transmitter. The measured PTE was greatly improved in comparison to that of a conventional system. These results demonstrate that the PTE is enhanced by using the NIC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.466-473
• /
• 2013

In this paper, a compact planar multi-loop self-resonant coil of high quality factor with a coaxial cross section is proposed for effective wireless charging. The proposed coil has high Q-factor and a resonant frequency of a coil can be easily controlled by adjusting distributed capacitance. For designing the coil, a self-inductance and a distributed capacitance are calculated theoretically. The self-inductance is calculated from the sum of the mutual energies between small circular loops that are made by dividing the cross section of the coil. To verify its properties and calculation results, the self-resonant coils are fabricated by using a coaxial cable with characteristic impedance of $50{\Omega}$. The measured frequencies are very consistent with the calculated ones. In addition, the resonant frequency can be adjusted slightly by the tuning parameter ${\gamma}$. The resonant coils are applied to a tablet PC, the Q-factors of the Tx and Rx resonant coils are 282 and 135, respectively. As a result of measurement when height between the two resonant coils is 4.4 cm, the power transfer efficiency is more than 80 % within a radius of 5 cm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7A
• /
• pp.724-729
• /
• 2007

In this paper, we consider a joint optimization of transmitter and receiver in additive cyclostationary noise with zero forcing criterion. We assume that the period of the cyclostationary noise is the same as the inverse of the symbol transmission rate and that the noise has a positive-definite autocorrelation function. The data sequence is modeled as a wide-sense stationary colored random process and the channel is modeled as a linear time-invariant system with a frequency selective impulse response. Under these assumptions and a constraint on the average power of the transmitted signal, we derive the optimum transmitter and receiver waveforms that jointly minimizes the mean square error with no intersymbol interference. The simulation results show that the proposed system has a better BER performance than the systems with receiver only optimization and the systems with no transmitter and receiver optimization.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.1
• /
• pp.89-93
• /
• 2020

In this paper, Ku-band Receiver for compact doppler radar has been designed and fabricated. It composed of MWR(Microwave Receiver) and IFR(Intermediate Frequency Receiver) which have 5 receive path. We applied limiter circuit to protect MWR from Tx leakage power and maximum 2 W. IFR can change the Rx path to broad band or narrow band by MSC(Mode Selection Switch). It is observed that fabricated receiver performs 68 dB gain and 3.7 dB noise figure, 93 ns limiter recovery time. Proposed Ku-band receiver is expected to apply for Ku-band compact doppler radar.