• Journal of Ocean Engineering and Technology
• /
• v.27 no.3
• /
• pp.73-78
• /
• 2013

CFD (computational fluid dynamics) analyses that considered the dynamic interaction effects between the flow and a turbine were performed to evaluate the power output characteristics of two representative vertical-axis tidal-current turbines: an H-type Darrieus turbine and Gorlov helical turbine (GHT). For this purpose, a commercial CFD code, Star-CCM+, was utilized, and the power output characteristic were investigated in relation to the scale ratio using the relation between the Reynolds number and the lift-to-drag ratio. It was found that the power coefficients were significantly reduced when the scaled model turbine was used, especially when the Reynolds number was lower than $10^5$. The power output characteristics of GHT in relation to the twisting angle were also investigated using a three-dimensional CFD analysis, and it was found that the power coefficient was maximized for the case of a Darrieus turbine, i.e., a twisting angle of $0^{\circ}$, and the torque pulsation ratio was minimized when the blade covered $360^{\circ}$ for the case of a turbine with a twisting angle of $120^{\circ}$.

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.04a
• /
• pp.127-133
• /
• 1997

Authors measured the apparent contact angle in a yarn using microscope because it gives a useful information in the evaluation of comfort factors in fabrics. The mechanical stage of microscope was designed and built to facilitate this measurement. Variables examined were the fiber type, the twisting number, and the fluid type. All produced significant effect most of which could be rationalized based on the known concepts. The methodology used and the results obtained are discussed in detail.

• Structural Engineering and Mechanics
• /
• v.9 no.6
• /
• pp.541-555
• /
• 2000

Pultruded cross-sections are always thin-walled due to constraints in the manufacturing process. Thus, the buckling strength determines the overall strength of the member. The elastic buckling of pultruded angle sections subjected to direct compression is studied. The lateral-torsional buckling, very likely to appear in thin-walled cross-sections, is investigated. Plate theory is used to allow for cross-sectional distortion. Shear effects and bending-twisting coupling are accounted for in the analysis because of their significant role. A simplified approach for determining the maximum load of equal leg angle sections under compression is presented. The analytical results obtained in this study are compared to the manufacturer's design guidelines for compression members as well as with the design specifications for steel structural members. Experimental results are obtained for various length specimens of pultruded angle sections. The results presented in this paper correspond to actual pultruded equal leg angle sections being used in civil engineering structures.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.524-530
• /
• 2015

Early wearable robotic devices were big, powerful and manipulator-like. Recently, various applications of wearable robotics have shown a greater demand for lower weight and compliancy. One approach to achieve these objectives is the use of novel actuators such as twisted string actuators. These actuator are very light, quiet, mechanically simple and compliant. Therefore, they can drastically decrease the weight and size of robotic systems such as exoskeletons. However, one drawback of this actuator is its nonlinear transmission ratio, which is established as a ratio between the angle of twisting of the strings and their resulting contraction. In this paper, we propose a transmission mechanism with rotational motion as the output incorporating a twisted string actuator (TSA). The designed mechanism allows the linearization of the relationships between the input and output displacements and forces of a TSA. The proposed design has been validated theoretically and through a set of computer simulations. A detailed analysis of the performance of the proposed mechanism is presented in this paper along with a design guideline.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.201-204
• /
• 2008

In this paper, several process parameter studies of the manufacturing process of the steel cords are carried out to verify the relation between the process parameters and the residual stresses on the steel cords. At first, the finite element analysis of the drawing process is performed and the residual stress distributions with respect to the wire material and the area reduction ratio are obtained. The residual stress of the drawn wire is imported the finite element analysis of the twisting process as an initial stress. After that a parameter study of the twisting process is carried out. The process parameters are the applied tension, the over-twisting angle and the tensile strength of the drawn wire. Based on these studies, the optimum values of the process parameters which can remove or reduce the undesired residual stresses are determined. The optimum value of the process parameters are confirmed by the finite element analysis of the elastic recovery process of the steel cords. Finally, the finite element analysis of the roller straightening process is done to study the variation of the distribution of the residual stress before and after the process.

• Steel and Composite Structures
• /
• v.3 no.4
• /
• pp.261-275
• /
• 2003

Truss members built-up with double angles back-to-back have monosymmetric cross-section and twisting always accompanies flexion upon the onset of buckling about the axis of symmetry. Approximate formulae for calculating the buckling capacity are presented in this paper for routine design purpose. For a member susceptible only to flexural buckling, its optimal cross-section should consist of slender plate elements so as to get larger radius of gyration. But, occurrence of twisting changes the situation owing to the weakness of thin plates in resisting torsion. Criteria for limiting the leg slenderness are discussed herein. Truss web members in compression are usually considered as hinged at both ends for out-of-plane buckling. In case one (or both) end of member is not supported laterally by bracing member, its adjoining members have to provide an elastic support of adequate stiffness in order not to underdesign the member. The stiffness provided by either compression or tension chords in different cases is analyzed, and the effect of initial crookedness of compression chord is taken into account. Formulae are presented to compute the required stiffness of chord member and to determine the effective length factor for inadequately constrained compressive diagonals.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.7 no.4
• /
• pp.161-166
• /
• 1982

In this paper, the intrinsic birefringence and twist-induced rotation of the single mode optical fiber have been investigated. On the analysis, the optical fiber has been modeled as a linear retarder and the intrinsic linear retardation of the single mode optical fiber is approximately found to be 2.57'/m from the measurement. Theoretically analyzing the twist-induce rotation by the purturbation theory, it is found that the magnitude of the twist-induced rotation varies linearly with the twisted angle. And this theorerical result has been in good accord with the experimental result.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.333-341
• /
• 2009

In this paper arc behavior in spiral type vacuum interrupter(VI) was analyzed by means of arc images, arc voltages and finite element method(FEM). As a result of experiment, the difference of arc voltage was observed under different twisting angles. It was found that the reason of the difference was the difference of arc resistance from simultaneous analysis of arc images and arc voltages. and the difference of arc resistance was explained by Lorentz force calculation with FEM. And the results of calculation were sufficient to explain the experimental results.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.406-410
• /
• 2001

For 4-conductor bundle transmission line spacer damper are equipped so as to keep the spacing between sub conductors. For 4-conductor bundle the subspan spacing of a spacer damper is determined and applied in order that the bundle may get restored to a normal state when 4-conductor bundle is rolled by rigid body vibration due to wind. But 4 conductors of 345kV 4-conductor bundle transmission line were twisted by the angle of $315^{\circ}$ for the first time korea. In this paper, we will analyze the reason of the power line twisting of 4-conductor bundle which occurred for the first time in korea and offer the preventive countermeasures for this

• The Journal of Advanced Prosthodontics
• /
• v.6 no.1
• /
• pp.39-45
• /
• 2014

PURPOSE. The aim of the present study was to evaluate the accuracy of three techniques for correction of cast implant bars. MATERIALS AND METHODS. Thirty cast implant bars were fabricated on a metal master model. All cast implant bars were sectioned at 5 mm from the left gold cylinder using a disk of 0.3 mm thickness, and then each group of ten specimens was corrected by gas-air torch soldering, laser welding, and additional casting technique. Three dimensional evaluation including horizontal, vertical, and twisting measurements was based on measurement and comparison of (1) gap distances of the right abutment replica-gold cylinder interface at buccal, distal, lingual side, (2) changes of bar length, and (3) axis angle changes of the right gold cylinders at the step of the post-correction measurements on the three groups with a contact and non-contact coordinate measuring machine. One-way analysis of variance (ANOVA) and paired t-test were performed at the significance level of 5%. RESULTS. Gap distances of the cast implant bars after correction procedure showed no statistically significant difference among groups. Changes in bar length between pre-casting and post-correction measurement were statistically significance among groups. Axis angle changes of the right gold cylinders were not statistically significance among groups. CONCLUSION. There was no statistical significance among three techniques in horizontal, vertical and axial errors. But, gas-air torch soldering technique showed the most consistent and accurate trend in the correction of implant bar error. However, Laser welding technique, showed a large mean and standard deviation in vertical and twisting measurement and might be technique-sensitive method.