• 한국기계가공학회지
• /
• 제18권12호
• /
• pp.7-14
• /
• 2019

A marine turning gear controls the position of the piston-crank mechanism by rotating the flywheel of the marine engine at a low speed, which is the main auxiliary machine that enables the disassembly and maintenance of the engine. In this study, the safety factor for surface durability and tooth bending strength was improved by the design modification of the marine turning gear based on the spur planetary gear. Angular velocity, torque, and efficiency of the turning gear were measured using a reliability evaluation tester, and a multibody dynamics model for analysis corresponding to the test results was developed. Finally, it was confirmed that the design improvements improved the tooth surface damage of the sun gear in the 3^rd reduction stage.

• Design & Manufacturing
• /
• 제15권1호
• /
• pp.66-71
• /
• 2021

In this study, die turning injection(DTI) mold design for manufacturing reservoir fluid tanks used for cooling in-vehicle batteries, inverters, and motors was conducted based on multi-field CAE. Part design, performance evaluation, and mold design of the reservoir fluid tank was performed. The frequency response characteristics through modal and harmonic response analysis to satisfy the automotive performance test items for the designed part were examined. Analysis of re-melting characteristics and structural analysis of the driving part for designing the rotating die of the DTI mold were performed. Part design was possible when the natural frequency performance value of 32Hz or higher was satisfied through finite element analysis, and the temperature distribution and deformation characteristics of the part after injection molding were found through the first injection molding analysis. In addition, it can be seen that the temperature change of the primary part greatly influences the re-melting characteristics during the secondary injection. The minimum force for driving the turning die of the designed mold was calculated through structural analysis. Hydraulic system design was possible. Finally, a precise and efficient DTI mold design for the reservoir fluid tank was possible through presented multi-field CAE process.

• 대한조선학회논문집
• /
• 제58권4호
• /
• pp.253-261
• /
• 2021

This paper describes the process of evaluating maneuverability in still water of an unmanned surface vehicle based on data measured by performing sea trials. First, we set up a test scenario that is easy to analyze the maneuverability of the unmanned surface vehicle and to identify and verify the dynamics model. Since the attitude of hull varies according to the speed of the unmanned surface vehicle which has a planing hull shape, the relationship between waterjet RPM, speed and attitude is analyzed by performing straight forward tests at various speeds. The turning tests of the unmanned surface vehicle in which the waterjet angle rotates while turning are performed by changing the waterjet rotation angle under the condition of two representative speeds to analyze turning ability. The turning ability of the unmanned surface vehicle includes speed reduction, yaw rate, heel, and turing diameter at steady turning phase according to the speed and RPM.

• 항공우주시스템공학회지
• /
• 제8권3호
• /
• pp.47-54
• /
• 2014

This is a research on the method of how to improve stall characteristics for the small general aviation airplanes to meet the FAR part 23 requirements. This research is based on the experience of certification flight tests of KC-100 airplane for Korea type certification. KAS/FAR Part 23.201/203 are the stall characteristics requirements. 23.201 requires to show the stable stalling tendency of the wings level stall and 23.203 requires to show the stable stalling tendency of stall characteristics during turning flight. In this paper, the stall characteristics requirements, improvement methods and flight test experience of KC-100 airplane for type certification.

• 수산해양기술연구
• /
• 제41권4호
• /
• pp.289-295
• /
• 2005

This study is intended to provide navigator with specific information necessary to assist in the avoidance of collision and in operation of ships to evaluate the manoeuvrability of own ship. The actual manoeuvering characteristics of ship can be adequately judged from the results of typical ship trials manoeuvres. Author carried out sea trials based full scale for turning test, zig-zag test, spiral tests and crash-stop test at actual sea going condition. The turning circle manoeuvres were performed on starboard and port sides with $35^{\circ}$ rudder angle at the service speed, and Zig-zag procedures were performed on both sides with $10^{\circ}$ and $20^{\circ}$ rudder angle respectively. Spiral tests were carried out on the both sides and crash stop test was also carried out. The results from tests could be compared directly with the standards of manoeuverability of IMO and consequently the manoeuvring qualities of the ship is fully satisfied with its.

• 한국ITS학회 논문지
• /
• 제2권1호
• /
• pp.41-52
• /
• 2003

본 연구의 목적은 기존 신호운용체계의 효율적인 운용과 안전한 보행자 통행시간을 보장한다는 전제하에, 신호교차로 에서 보행자신호로 인해 발생하는 불합리한 좌회전차량의 꼬리물림현상과 우회전차량 진행불가현상이 직진 교통류에 미치는 소통장애를 해소하는 방안을 제시하는 것이다. 본 연구에서 제시하는 방안은 차량직진신호 점등 후 몇 초 정도의 시차(步行者信號 前時間)를 두고 보행자신호를 운용함으로써 보행이 시작되기 전에 회전교통류가 교차로에서 소거되도록 하는 것이다. 이를 위하여 첨두시간에 교차로에서 보행자신호 전시간을 점차 확장시키는 방법으로 좌회전 꼬리물림$\cdot$우회전 진행불가차량 발생현상을 현장조사 하였으며, 분석결과는 다음과 같다. 첫째, 보행자신호 전시간을 연장할수록 직진교통류 소통장애를 야기하는 좌회전 꼬리물림현상과 우회전 진행불가현 상이 현저히 감소하였다. 둘째, 교차로와 횡단보도간의 대기공간이 수용할 수 있는 범위 내에서는 좌회전 꼬리물림차량과 우회전 진행불가차량도 직진차량에 장애를 주지 않았다. 셋째, 이중 횡단보도에서는 신호현시체계상 좌회전 꼬리물림현상이 발생치 않으며 우회전 진행불가현상은 충분한 대기공간으로 인해 직진차량에 미치는 영향이 미미하였다. 검증 결과 보행자신호 전시간 부여는 교차로 소통효율성 증진에 유의한 것으로 판단되었으며 이를 운용하기 위해서는 회전교통량과 횡단보도의 위치$\cdot$종류에 따라 개개 교차로별로 보행자신호 전시간이 설정되어야 한다는 결론을 얻었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권5호
• /
• pp.482-490
• /
• 1997

The effects of strain amplitude. test temperature and stress on the fatigue properties for Ti-Ni wires were investigated using a rotary bending fatigue tester specially designed for wires. The fatigue test results were discussed in connection with the static tensile properties. The DSC measurement was conducted after fatigue test in order to clarify the change of transformation behavior due to the progress of fatigue. Under the temperature below or near the Af, the strain amplitude($\varepsilon_a$)-failure life (Nf) curve showed to be composed of three straight lines with two turning points. Of the 2 turning points, the upper one was coincident with the elastic limit strain and the lower one with the proportional limit strain. With rising of the test temperature above Af, the pattern of $\varepsilon_a$-Nf curve changed gradually to composition of 2 straight lines. The $\varepsilon_a$-Nf curve shifted depending on test temperature. In the short and medium life zones, the higher the temperature was, the shorter the fatigue life. However, in the long life zone, above the Af temperature, the fatigue life was not affected by the temperature. The transformation enthalpy measured after fatigue test was dependent on Nf, $\varepsilon_a$, and test temperature.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.359-364
• /
• 1999

Due to rapid growth of die and mould industries, it is urgently required to maximize the productivity and the efficiency of machining. In recent years, owing to the development of new kinds of material, die and mould materials are much harder and it is more difficult to cut. In this study, the workpiece SKD11(HRC45) is cut with TiAlN coated tungsten-carbide cutting tools. To find the general characteristics of difficult-to-cut materials, orthogonal turning test is performed. Orthogonal cutting theory can be expanded to oblique cutting model. The oblique cutting process in the small cutting edge element has been analyzed as orthogonal cutting process in the plane containing the cutting velocity vector and chip-flow vector. Hence, with the orthogonal cutting data obtained from orthogonal turning test, the cutting forces can be analyzed through oblique cutting model. The simulation results have shown a fairy good agreement with the test results.

• 한국해양공학회지
• /
• 제27권6호
• /
• pp.112-118
• /
• 2013

This paper reports the results of a comparative study on rudder performance between the steel rudders that have been used in coastal angling fishing boats in the 20-GT class and the newly developed FRP composite material rudders. In order to compare the rudder performances of these two types, a sea trial test was carried out to investigate the speed performance, fuel consumption, and ship's turning ability. The results showed that the sea trial performance of the FRP composite rudder was better than that of the steel rudder type in terms of the sea speed, fuel consumption rate, and turning ability.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2018년도 추계학술대회
• /
• pp.12-13
• /
• 2018

안전운항을 위해 항해사가 숙지하고 있어야하는 것은 선박의 조종성능이다. 선박이 조우하는 상황이나 위험상황에 처했을 때 피항동작을 취하기 위해 변침을 하게 되는데 그러한 조치를 취하기 위해 타각을 얼마큼 줄 건지를 판단하고 직진상태에서 타각을 사용한 이후 정해진 방향으로 바꾸는데 필요한 시간과 어떻게 운동하는지를 예측할 수 있어야 선박의 안전을 확보할 수 있다. 실습선 한바다호의 조종성능을 확인하기 위해 IMO에서 제시하는 $10^{\circ}/10^{\circ}$ 및 $20^{\circ}/20^{\circ}$ 지그재그 테스트와 좌현/우현 선회시험을 시행하였고 실선계측을 통해 이 때 나타나는 선박의 운동을 함께 측정하여 항해사들이 적절한 피항동작을 취할 수 있도록 실습선 한바다호의 조종성능과 선박운동의 정보를 제공하고자 한다.