• 제목/요약/키워드: Tubular Surface

검색결과 178건 처리시간 0.022초

In Situ NMR 진단용 원통형 직접 메탄올 연료전지 (Tubular Type Direct Methanol Fuel Cell for in situ NMR Diagnosis)

  • 조한익;엄명섭;한기성;한옥희;하흥용;김수길
    • 전기화학회지
    • /
    • 제12권4호
    • /
    • pp.329-334
    • /
    • 2009
  • 본 연구는 연료전지 운전시 전극 촉매 및 전해질막 내에서 발생하는 연료 및 산화제의 산화/환원 반응 메커니즘, 이동현상, 구성품 열화현상 등을 핵자기 공명 (NMR, Nuclear Magnetic Resonance)을 이용하여 연료전지의 분해나 시료 채취 없이 제자리 (in situ) 분석할 수 있는 진단장치용 연료전지 개발에 관한 것이다. NMR에 사용되는 연료전지는 특수하게 제작된 TCD (Toroid Cavity Detector) 탐침 내부에서 작동하여야 하며, TCD 탐침이 가지는 기하학적 제한 요소들로 인해 일반적인 평판형 연료전지와 달리 원통형으로 제작된다. 이로 인해 반응물의 공급이나 생성물의 제거가 어려우며 누수 현상 및 불균일한 압력 분배가 발생하여 성능이 낮다. 따라서, in situ NMR 분석용 연료전지가 가지는 구조상의 특징인 원통형에 적합한 유로를 설계하고 제작하여 물질 전달 특성을 개선해야 할 필요성이 있다. 본 연구에서는 NMR 장비 내의 자기장에 영향을 미치지 않는 비자성 물질을 이용해 원 통형 공기극 유로를 개발하여, 산소의 공급 및 반응물의 제거를 원활하게 하였다. 또한, 체결 압력을막-전극 접합체에 균일하게 분배하여 누수 및 누액을 차단하였다. 이를 통해, 상온에서 약 $36mW/cm^2$의 우수한 성능을 나타내는 in situ NMR 진단용 직접 메탄올연료전지 시스템을 개발하였다.

Wave propagation in a concrete filled steel tubular column due to transient impact load

  • Ding, Xuanming;Fan, Yuming;Kong, Gangqiang;Zheng, Changjie
    • Steel and Composite Structures
    • /
    • 제17권6호
    • /
    • pp.891-906
    • /
    • 2014
  • This study aims to present a three dimensional finite element model to investigate the wave propagation in a concrete filled steel tubular column (CFSC) due to transient impact load. Both the concrete and steel are regarded as linear elastic material. The impact load is simulated by a semi sinusoidal impulse. Besides the CFSC models, a concrete column (CC) model is established for comparing under the same loading condition. The propagation characteristics of the transient waves in CFSC are analyzed in detail. The results show that at the intial stage of the wave propagation, the velocity waves in CFSC are almost the same as those in CC before they arrive at the steel tube. When the waves reach the column side, the velocity responses of CFSC are different from those of CC and the difference is more and more obvious as the waves travel down along the column shaft. The travel distance of the wave front in CFSC is farther than that in CC at the same time. For different wave speeds in steel and concrete material, the wave front in CFSC presents an arch shape, the apex of which locates at the center of the column. Differently, the wave front in CC presents a plane surface. Three dimensional effects on top of CFSC are obvious, therefore, the peak value and arrival time of incident wave crests have great difference at different locations in the radial direction. High-frequency waves on the waveforms are observed. The time difference between incident and reflected wave peaks decreases significantly with r/R when r/R < 0.6, however, it almost keeps constant when $r/R{\geq}0.6$. The time duration between incident and reflected waves calculated by 3D FEM is approximately equal to that calculated by 1D wave theory when r/R is about 2/3.

20세기 초기 서양 흔들의자의 양식적 특징 (Study on the Characteristics of Western Rocker style In Early 20th Century)

  • 임승택
    • 농업생명과학연구
    • /
    • 제45권6호
    • /
    • pp.21-32
    • /
    • 2011
  • 본 연구는 20세기 초기의 서양 흔들의자를 분석하여 조형적, 실용적 관점에서 양식적 특징을 학문적으로 규명하고, 오늘날 우리나라 흔들의자의 설계 및 제작의 기초자료를 제공하는 것에 목적이 있다. 20세기 전반의 서양 흔들의자(1925~1945년 제작)는 형태가 기능을 따라야 한다는 단순한 기능주의의 이념을 적극적으로 표현하였다. 원목을 활용한 흔들의자는 표면장식을 배제하였고, 강철관 프레임의 흔들의자는 검정색 가죽의 업홀스터리를 즐겨 사용하면서 노출된 구조미를 대담하게 표현하였다. 또 강철관을 통하여 가구의 경량화가 이루어졌고 곡선미 있는 새로운 양식이 출현하였다. 근대 흔들의자의 구조는 양식과 기능적 이유에서 모두 중요하게 되었다. 디자이너들은 강철관과 목재 프레임의 노출된 구조를 통합성 및 합리성과 결부 시켜 디자인의 평등주의 스타일을 만들어냈다. 특히 이 시기에는 밝고 대담한 색상의 업홀스터리와 목재 프레임으로 구성된 흔들의자가 근대적 특징의 단순한 형태로 다양하게 표현되었다.

콘크리트 충전강관 구조의 직경-두께비 및 콘크리트 강도 변화에 따른 휨 성능 평가 (Bending Performance Evaluation of Concrete Filled Tubular Structures With Various Diameter-thickness Ratios and Concrete Strengths)

  • 이상열;박대용;이상범;이래철
    • 한국구조물진단유지관리공학회 논문집
    • /
    • 제13권2호통권54호
    • /
    • pp.223-230
    • /
    • 2009
  • 본 연구는 다양한 직경-두께비와 콘크리트 강도를 고려한 콘크리트 충전강관의 휨 거동을 다루었다. 유한 요소 해석을 위하여 상용 프로그램 LUSAS를 사용하였으며, 충전 강관의 콘크리트와 강 사이의 부착면의 상세거동을 고려하기 위하여 조인트 요소를 적용하였다. 또한, 콘크리트와 강관의 비선형성을 고려하기 위하여 소성영역에서 증가된 응력을 사용한 콘크리트와 강의 응력-변형률 곡선을 사용하였다. 제안된 방법으로 구한 수치해석 결과는 등분포하중을 받는 강관의 하중-변위 곡선에 대한 실제 실험 결과와 잘 일치하였다. 몇 가지 매개변수 연구는 서로 다른 직경-두께비와 콘크리트 강도에 대하여 휨 영향을 받는 콘크리트 충전강관의 구조적 특성에 초점을 두었다.

콘크리트 충진 유리섬유 복합소재 튜브 합성압축부재의 구조적 특성분석 (Structural Characteristics of Concrete Filled Glass Fiber Reinforced Composite Tube)

  • 이성우;박신전;최석환
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
    • /
    • pp.571-574
    • /
    • 1999
  • Due to many advantages of advanced composite material, research on the composite compression member is initiated. In this paper structural characteristics of concrete filled glass fiber reinforced composite tubular member si studied. Experimental results shows that strength and ductility of composite compression member is considerably increased due to concrete confinement action of composite surface. Thus it can be anticipated that increased strength of concrete will be incorporated in the design of composite compression member.

  • PDF

복합소재의 건설분야 응용현황과 콘크리트 합성압축부재의 개발 (Application of Composites to Construction Industry and Development of Concrete Filled Composite Compression Member)

  • 이성우;박신전
    • 한국복합재료학회:학술대회논문집
    • /
    • 한국복합재료학회 1999년도 추계학술발표대회 논문집
    • /
    • pp.183-188
    • /
    • 1999
  • Due to many advantages of advanced composite materials, research on the application of composites to the construction industry is initiated. In this paper, fabrication methods efficient for infrastructures and application examples of each method are discussed. It also presents the structural characteristics of concrete filled glass fiber reinforced composite tubular member. Experimental results shows that strength and ductility of composite compression member is considerably increased due to concrete confinement action of composite surface.

  • PDF

SiCf/SiC 복합체의 화학기상침착 거동에 미치는 권선 구조와 침착 변수의 영향 (Influence of Winding Patterns and Infiltration Parameters on Chemical Vapor Infiltration Behaviors of SiCf/SiC Composites)

  • 김대종;고명진;이현근;박지연;김원주
    • 한국세라믹학회지
    • /
    • 제51권5호
    • /
    • pp.453-458
    • /
    • 2014
  • SiC and its composites have been considered for use as nuclear fuel cladding materials of pressurized light water reactors. In this study, a $SiC_f$/SiC composite as a constituent layer of SiC triplex fuel cladding was fabricated using a chemical vapor infiltration (CVI) process in which tubular SiC fiber preforms were prepared using a filament winding method. To enhance the matrix density of the composite layer, winding patterns, deposition temperature, and gas input ratio were controlled. Fiber arrangement and porosity were the main parameters influencing densification behaviors. Final density of the composites decreased as the SiC fiber volume fraction increased. The CVI process was optimized to densify the tubular preforms with high fiber volume fraction at a high $H_2$/MTS ratio of 20 at $1000^{\circ}C$; in this process, surface canning of the composites was effectively retarded.

Shear strength formula of CFST column-beam pinned connections

  • Lee, Seong-Hui;Kim, Young-Ho;Choi, Sung-Mo
    • Steel and Composite Structures
    • /
    • 제13권5호
    • /
    • pp.409-421
    • /
    • 2012
  • Recently, as the height of building is getting higher, the applications of CFST column for high-rise buildings have been increased. In structural system of high-rise building, The RC core and exterior concrete-filled tubular (CFST) column-beam pinned connection is one of the structural systems that support lateral load. If this structural system is used, due to the minimal CFST column thickness compared to that of the CFST column width, the local moment occurred by the eccentric distance between the column flange surface from shear bolts joints degrades the shear strength of the CFST column-beam pinned connections. This study performed a finite element analysis to investigate the shear strength under eccentric moment of the CFST column-beam pinned connections. The column's width and thickness were used as variables for the analysis. To guarantee the reliability of the finite element analysis, an actual-size specimens were fabricated and tested. The yield line theory was used to formulate an shear strength formula for the CFT column-beam pinned connection. the shear strength formula was suggested through comparison on the results of FEM analysis, test and yield lime theory, the shear strength formula was suggested.

단면형상에 따른 단일겹치기 이음의 피로 및 정적 토크 전달특성에 관한 실험적 연구 (Effect of the Cross Sectional Shapes on the Static and Fatigue Torque Transmission Capabilities of Adhesive Single Lap Joints)

  • 최진경;이대길
    • 대한기계학회논문집
    • /
    • 제18권4호
    • /
    • pp.835-845
    • /
    • 1994
  • In this paper, the effects of the adhesive thickness and adherend roughness on the static and fatigue strengths of the adhesively bonded circular single lap joints has been investigated by an experimental method. The stacking sequence effect of the composite adherend on the static and fatigue strength and the fracture patterns of the adhesive failure were also observed. Since the circular single lap joint fails catastrophically beyond the static strength of fatigue limit, the tubular polygonal adhesively bonded joints such as triangular, tetragonal, pentagonal, hexagonal as well as elliptical joints were manufactured in order to give partial mechanical characteristics to the adhesively bonded tubular joints. These joints were tested both in static and fatigue modes. From the experimental investigations, it was found that the fatigue strength of the circular adhesively bonded joints was much dependent on the arithmetical average surface roughness of the adherends and the polygonal adhesively bonded joints had better fatigue strength characteristics than the circular adhesively bonded joints.

Pneumocystis carinii 폐렴의 기관지 폐포세정액: 세포학적 및 전자현미경적 소견 (Bronchoalveolar Lavage of Pneumocystis carinii Pneumonia: Cytological and Ultrastructural Features)

  • 권건영;윤철희;김상표;박관규;장은숙
    • 대한세포병리학회지
    • /
    • 제5권1호
    • /
    • pp.1-9
    • /
    • 1994
  • The cytological and ultrastructural findings of Pneumocystis carinii(PC) obtained from rats by bronchoalveolar lavage (BAL) are described. All developmental forms of the PC organisms were obtained in the lavage fluid. Papanicolaou stain revealed conglomeration of PC as a foamy cast. The cystic walls of PC were well identified on Gomori's methenamine silver stain. Trophozoites and intracystic bodies were stained by Giemsa and Diff-Quik techniques. Some PC organisms were seen within the alveolar macrophages. Ultrastructurally, the cysts were almost circular in shape, and were nearly devoid of surface tubular extensions. The wall of the cyst was composed of an unit membrane, an intermediate electron lucent layer and an external electron dense layer The cysts frequently contained intracystic bodies, so called sporozoites. Occasionally empty or collapsed cysts with no intracystic bodies, and precysts were found. Trophozoites were variable in size and shape with abundant tubular extensions along the single electron dense pellicle. BAL is a useful method for concentrating the various morphologic forms of PC organisms, and is a rapid diagnostic method for PC pneumonia.

  • PDF