• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.81-86
• /
• 2005

In this work, we propose a new ultrasonic damage inspection method in plate structures. The proposed method employs an OPMT(orientation-adjustable patch-type magnetostrictive transducer) in order to make the ultrasonic waves directed to a specific target point. For experiments, virtual grid points were set up at every 50 mm in an aluminum plate and two OPMTs were used for inspection. If there exists a crack in a plate, the reflected Lamb wave from the crack is measured in addition to the direct waves from the transmitting transducer to the receiving transducer.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.423-427
• /
• 2004

In this work, we propose a new ultrasonic damage inspection method in plate structures. The proposed method employs an OPMT (Orientation-adjustable Patch-type Magnetostrictive Transducer) in order to make the ultrasonic waves focused on the specific target point. For experiments, virtual grid points were set up at every 50 mm in an aluminum plate and two OPMTs were used for inspection. If there exists a crack in a plate, the reflected Lamb wave from the crack is measured in addition to the direct waves from the transmitting transducer to the receiving transducer.

• 한국소음진동공학회논문집
• /
• 제25권2호
• /
• pp.124-132
• /
• 2015

The paper deals with the energy transmission of the elastic waves obliquely transmitting and refracting through a plate and a pipe. By calculating the transmitting ratio depending on the incidence angle, the angle corresponding to the maximum transmission was determined theoretically and considered in the design of ultrasonic transducers for flow velocimetry. Experiments were carried out by using prototypes of the transducers. Experimentally-obtained transmission ratios were compared with and confirmed the theoretically-calculated results.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.177-183
• /
• 2008

For 10 kW-class Stirling engine using scroll expander and scroll compressor, considerations on thermal expansion of the fixed and orbiting scroll members of the scroll expander due to high gas temperature at the expander inlet has resulted in adopting of the keys between the fixed scroll and main frame for the fixed scroll side and spring type insertion between the orbiting scroll base plate and supporting holders for orbiting scroll side. Dynamic analysis on the fixed and orbiting scroll members and the shafts of the scroll expander showed that using of these devices for complying thermal expansion caused large variations of the forces acting on the fixed scroll keys and on the power transmitting shafts and also on the shaft bearings.

• 한국표면공학회지
• /
• 제41권2호
• /
• pp.76-82
• /
• 2008

We investigated sterilization characteristics of UV lights by counting the number of bacteria units with varying sterilization time and distance from the light source. We focused on an idea that UV light of 184.9 nm could generate ozone and developed a new sterilizer. The UV-ozone duplex system sterilized bacteria faster than UV-only sterilizers. To reduce shadowing effects by target objects, we used UV transparent quartz plate as a support and put a reflecting plate. Distribution of UV irradiation intensity and ozone supply were analyzed by a 3D model and measured by a semiconductor UV sensor. But even with an Al reflector, multi-layered pens could not be treated properly from UV irradiation only. Ozone generating lamp could treat more uniformly multi-layered pens with a stirring fan by supplying ozone to shadowed surfaces.

• 전자공학회논문지D
• /
• 제35D권12호
• /
• pp.12-20
• /
• 1998

평행평판도파관에 유한한 개수의 슬릿으로 이루어진 비균일한 누설파 구조를 송(수)신 누설파 안테나와 격자 결합기의 관점에서 해석하였다. 특정한 복소 전파상수분포를 갖는 누설파 구조를 구성하기 위하여 누설파 구조를 따라 주기와 슬릿의 폭을 함께 변화시켰다. 가우스, 균일, 코사인, 코사인 제곱, Taylor 분포와 같은 다양한 전원(등가 자계전류)분포를 갖는 누설파 구조의 슬릿영역의 등가 자계전류와 복사특성에 관한 결과들을 제시하고 상호 비교하여 보았다.

• 센서학회지
• /
• 제28권5호
• /
• pp.318-322
• /
• 2019

In shooting training, an impact point identification system that uses the impact wave of the bullet to check the impact point in the target plate has been recently used. Acoustic sensors used in these systems must be able to detect shock waves of high sound pressure levels and be both waterproof and dustproof for rainy weather and dusty environments, respectively. In this study, membranes with excellent waterproof, dustproof, and sound transmitting characteristics were selected through a characteristics test; a protection cap was installed to install the selected materials. After coupling the produced protection cap to the acoustic sensor housing, the sensitivity and phase characteristics of the acoustic sensor were checked. Through the waterproof and dustproof test, the performances of its sensitivity and phase characteristics were confirmed. Finally, the normal shockwave of a 5.56 mm diameter bullet was measured using a shockwave detection signal collecting plate equipped with a prototype of the acoustic sensor at a 100 m firing range.

• 제어로봇시스템학회논문지
• /
• 제20권11호
• /
• pp.1147-1152
• /
• 2014

This paper describes the design of a four-axis force/torque sensor with PSPBs (Parallel Step Plate Beams). The sensor is composed of eight PSPBs, a force/torque transmitting block, and fixing blocks. It is designed by using the FEM(Finite Element Method), and fabricated by using strain gages. The characteristic tests of the sensor are carried out, and the interference error, repeatability error, and non-linearity error are less than 2.21%, 0.03% and 0.03%. Furthermore, the structure of the four-axis force/torque sensor with PSPBs has a larger rated capacity than that of the four-axis force/torque sensor with PPBs under the same overall sensor size and the same rated output. It is thought that the developed four-axis force/torque sensor with PSPBs can be used for measuring the forces and torques in an intelligent robot, automation devices, etc.

• 한국공간구조학회논문집
• /
• 제7권6호
• /
• pp.83-90
• /
• 2007

철근 콘크리트 구조물에서 발생하는 진동 가진원과 영향에 대하여 많은 연구가 진행 중에 있다. 이러한 진동 가진원은 주로 거주자가 보행할 때 발생하는 하중이며, 발생한 가진원은 철근 콘크리트 판을 통하여 다른 거주자에게 전달된다. 이러한 전달원은 탄성파의 형태로 전달되는데 판의 표면으로 전달되는 표면파(Ram Wave)와 판의 내부로 전달되는 체적파(Prima Wave, Secondary Wave)의 형태로 전달된다 현재 이러한 파를 분석하는 연구는 압전소자(PZT)센서를 주로 사용하고 있으나, 콘크리트 부재에서 3축 형데로 전달되는 탄성파를 분석하기에는 여러 가지 어려운 부분이 많다. 따라서 이를 해결하기 위해 마이크로 가속도센서(Micro Accelerometer)를 이용하여 이동하중으로 발생하는 가진원에 대하여 평가하였다.

• 센서학회지
• /
• 제24권2호
• /
• pp.137-143
• /
• 2015

This paper describes the design of a two-axis force sensor with two step plate beams for measuring forces in an upper-limb rehabilitation robot. The two-axis force sensor is composed of a Fz force sensor and a Ty torque sensor. The Fz force sensor measures the force applied to a patient's arm pushed by a rehabilitation robot and the force of patient's arm. The Ty torque sensor measures the torque generated by a patient's arm motion in an emergency. The structure of sensor is composed of a force transmitting block, two step plate beams and two fixture blocks. The two-axis force sensor was designed using FEM (Finite Element Method), and manufactured using strain-gages. The characteristics test of the two-axis force sensor was carried out. as a test results, the interference error of the two-axis force sensor was less than 1.24%, the repeatability error of each sensor was less than 0.03%, and the non-linearity was less than 0.02%.