• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.575-582
• /
• 2007

In this paper, a 100 Watt high power amplifier has been implemented and performed evaluation, which is operating at UHF band ($470\;{\sim}\;806\;MHz$) for Digital TV repeater. To achieve increase of bandwidth and high power capability, 3-way power combiner and divider of Wilkinson type was adopted. In order to measure the fabricated 100 Watt power amplifier, the estimation technique function which makes equivalent mask was used. As a result of the measurement, the existence of pilot signal is confirmed and the signal transmitted at the rated output power 100 Watt is brought out the flat feature through 6 MHz bandwidth. and it resulted that its value was less than -47 dB at the edge of radiation channel and less than -110 dB at more than 6 MHz position from channel edge.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.287-287
• /
• 2009

The characteristics of slow wave structure employed for backward wave oscillators expected to be a high power microwave source are studied analytically and experimentary. The slow wave structure is a sinusoidally corrugated wall waveguide The dispersion relationn and transmitted characteristics for microwaves are measured in the air. There exist literatures on high efficiency of enhanced radiation from backward wave oscillators involving plasma studied experimentally.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.163-170
• /
• 2001

Axle Gearbox of the High Speed Train has rotational degree of freedom centered on the Axle Shaft Center Line, and constrained by the Reaction Arm connected to the Bogie Frame via Resilient Ring made of Rubber. This System is laid on the Power Train and can influence on the Power transmitted from Motor to Axle. The stiffeness of the Resilient Ring have to be selected for the Natural Frequency of this System do not overlap with the Teeth-mating Frequency. To confirm the Design Parameters, Calculation and Experiment were executed and compared.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.39-46
• /
• 1997

This study describes a computer aided design system on involute gear for power transmition. Input data for gear design are pressure angle $20^{\circ}$, transmitted power, gear volume, gear ratio, addendum ratio of rack, dedendum ratio of rack, edge radius of rack, allowable contact stress and allowable bending stress etc. Bending strength contact strength and scoring are considered as the design constraints. Method of optimization developed this study. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2001.11a
• /
• pp.79-82
• /
• 2001

The studies of the radiation-induced ignition of combustible atmospheres are of particular importance due to increasing use of optical sensors in industries such as coal mining and petroleum production. Because of the alleged intrinsic safety of such systems, substantial optical power is transmitted through optical fibers in potentially explosive atmospheres. However, there has been little experimental or theoretical research on the safety of optical power delivered by optical fiber systems in combustible atmospheres.(omitted)

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.93-100
• /
• 2003

Seismic isolation systems can improve the seismic safety of nuclear power plants by decreasing seismic force transmitted to structures and equipment. This study evaluates the effectiveness of equipment seismic isolation systems by the comparison of core damage frequencies in non-isolated and isolated cases. It can be found that the seismic isolation systems increase seismic capacity of nuclear equipment and decrease core damage frequencies significantly. The effect of equipment isolation is more significant in the PGA range of 0.3g to 0.5g.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.881-885
• /
• 2008

Wireless energy transmission system to a Micro Aerial Vehicle is now under development. A 5.8 GHz microwave phased array antenna and rectenna array receiver have been developed. An electric motor on a circling MAV model was driven by the transmitted power. In addition, 140GHz millimeter-waves of up to 1MW was beamed to a "Microwave Rocket" and its thrusting has been successfully demonstrated.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1627-1627
• /
• 2001

In this study, a newly constructed optical measurement system, whose main components were a parametric tunable laser and a near infrared photoelectric multiplier, was applied to detection of the information for the inside of Satsuma mandarin using time-of-flight near infrared spectroscopy (TOF-NIRS). The combined effects on the time resolved profile of sample diameter, sugar content, the wavelength of the laser beam, and the detection position of transmitted light were investigated in detail. The samples used were Satsuma mandarin (Citrus unshu $M^{ARC}$.) (location: Wakayama, Japan) having the diameters of 50-84 mm. The sugar content measured by a refractometer varied from 9.9 to 16.3 Brix%. Equator of sample was irradiated vertically with the pulsed laser, and transmitted output power was measured on the restricted position of the equator using the optical fiber cable. The sampling time and the number of averaging the output power were 100 ns and 100 times, respectively. The variation of the attenuance of peak maxima At, the time delay of peak maxima t and the variation of full width at half maximum w were strongly dependent on the detection position and the wavelength of the laser beam. At, t and w increased gradually as the sample diameter increased to be much absorbed and vigorously scattered. On the other hand, each optical parameter had a tendency to increase as the sugar content increased. Such behavior was remarkable when the transmitted light was detected at the side face of a sample. When we apply TOF-NIRS to detection of the information for the inside of fruit with high moisture content like Satsuma mandarin, it is very important to give attention to the difference in the scattered light within tissues and the semi-straightly propagated light. Furthermore, we tried to express the resulting phenomena by using a model samples composed of water, sucrose, and milk. The variation of the time resolved profile is strongly governed by the combination of the light absorption component, scattering medium, and refractive index.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1626-1626
• /
• 2001

In this study, a newly constructed optical measurement system, whose main components were a parametric tunable laser and a near infrared photoelectric multiplier, was applied to detection of the information for the inside of Satsuma mandarin using time-of-flight near infrared spectroscopy (TOF-NIRS). The combined effects on the time resolved profile of sample diameter, sugar content, the wavelength of the laser beam, and the detection position of transmitted light were investigated in detail. The samples used were Satsuma mandarin (Citrus unshu $M_{ARC}$.) (location: Wakayama, Japan) having the diameters of 50-84 mm. The sugar content measured by a refractometer varied from 9.9 to 16.3 Brix%. Equator of sample was irradiated vertically with the pulsed laser, and transmitted output power was measured on the restricted position of the equator using the optical fiber cable. The sampling time and the number of averaging the output power were 100 ns and 100 times, respectively. The variation of the attenuance of peak maxima At, the time delay of peak maxima $\Delta$t and the variation of full width at half maximum Δw were strongly dependent on the detection position and the wavelength of the laser beam. At, $\Delta$t and $\Delta$w increased gradually as the sample diameter increased to be much absorbed and vigorously scattered. On the other hand, each optical parameter had a tendency to increase as the sugar content increased. Such behavior was remarkable when the transmitted light was detected at the side face of a sample. When we apply TOF-NIRS to detection of the information for the inside of fruit with high moisture content like Satsuma mandarin, it is very important to give attention to the difference in the scattered light within tissues and the semi-straightly propagated light. Furthermore, we tried to express the resulting phenomena by using a model samples composed of water, sucrose, and milk. The variation of the time resolved profile is strongly governed by the combination of the light absorption component, scattering medium, and refractive index.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.880-883
• /
• 2006

The reduction of tool vibration has been a serious issue for both employers and workers because of the risks of vibration transmitted to the workers. In this study a hand-arm vibration measurement and evaluation system was developed based on ISO 5349:2001 and used for analyzing relation of vibration level and components of tools. This system consists of a notebook PC installed a LabVIEW program and the data acquisition system including two 3-axial accelerometers and a NI-DAQ card. Vibration measurement tests were conducted for eight angle grinders and four impact wrenches where 3 subjects were used for each of the tools. The relation between different components of each tool and its vibration total value made it possible to set-up a guideline of tool design. In the past engineers developed tools by using their experience and intuition, but by using this system it became possible to design tool components so as to minimize the risks of hand-transmitted vibration.