• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.2
• /
• pp.31-42
• /
• 1975

In this paper is introduced a new method of constructing a grounded.ungrounded FDNR (Frequency Dependent Negative Resistance) pair. Open circuit village transfer functions of any order are readily realized using the pairs with RC elements and CGIC's whose admittance ronversion functions are proportional to s3. This method simplifies the realization of transfer functions of higher order, The transfer function of fifth order haying low- pass filter characteristics is realized by this method. The measured frequency characteristics show satisfactory results.

• Journal of electromagnetic engineering and science
• /
• v.10 no.4
• /
• pp.237-243
• /
• 2010

A wireless power transfer system based on magnetically coupled two resonators is analysed using the filter theory. Design equations for each lumped parameter circuit components are derived. As a result, change of coupling coefficient between the resonators and/or change of load resistance are easily responded. Effect of circuit loss to the design theory is also addressed. After designing a power transfer system, a real system is constructed using spiral and loop coils. Dependence of circuit elements on their dimensions is measured in advance and used to cope with the designed element values. Simulated response by use of designed element values and measured result are compared, indicating the validity of the theory.

• Journal of electromagnetic engineering and science
• /
• v.16 no.2
• /
• pp.126-133
• /
• 2016

Wireless power transfer (WPT) efficiencies for multiple-input multiple-output (MIMO) systems are formulated with a goal of achieving their maximums using Z matrices. The maximum efficiencies for any arbitrarily given configurations are obtained using optimum loads, which can be determined numerically through adequate optimization procedures in general. For some simpler special cases (single-input single-output, single-input multiple-output, and multiple-input single-output) of the MIMO systems, the efficiencies and optimum loads to maximize them can be obtained using closed-form expressions. These closed-form solutions give us more physical insight into the given WPT problem. These efficiencies are evaluated theoretically based on the presented formulation and also verified with comparisons with circuit- and EM-simulation results. They are shown to lead to a good agreement. This work may be useful for construction of the wireless Internet of Things, especially employed with energy autonomy.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.221-230
• /
• 2007

This paper deals with analytical prediction for electromagnetic characteristics of a tubular linear actuator with Halbach array using transfer relations, namely, Melcher's methodology. Using transfer relations derived in terms of magnetic vector potential and a two-dimensional (2-d) cylindrical coordinate system, this paper derives analytical solutions for magnetic vector potential due to permanent magnets (PMs) and stator winding currents. On the basis of these analytical solutions, this paper also achieves analytical solutions for the magnetic fields distribution produced by PMs, stator windings current and axial thrust. The analytical results are validated extensively by finite element (FE) analyses. In particular, test results such as thrust measurements are given to confirm the analysis. Finally, this paper estimates control parameters using analytical solutions and test results such as thrust, back-emf, inductance and resistance measurements.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.12 no.3
• /
• pp.113-122
• /
• 2004

In case of heat exchangers operating under frosting condition, the thermal resistance and the air-side pressure loss increase with a growth of frost layer. In this paper, a transient characteristic prediction model of the heat transfer for a multi-inverter heat pump with frosting on its surface was presented by taking into account the change of the fin efficiency due to the growth of the frost layer. This dynamic simulation program was developed for a basic air conditioning system composed of an evaporator, a condenser, a compressor, a linear electronic expansion valve, and a bypass circuit. The theoretical model was derived from measured heat transfer and mass transfer coefficients. We also considered that the heat transfer performance was only affected by the decrease of wind flow area. The calculated results were compared with the experimental results for frosting conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.1013-1019
• /
• 2007

This paper is about structural analysis of globe valve for controlling cryogenic LNG's flow or stop in normal temperature. The used valve is demanded safety resistance for inner pressure and temperature variation caused by using it in cryogenic, high pressure surrounding. This study evaluates for safety resistance for inner pressure and temperature variation by heat transfer analysis in cryogenic surrounding, heat stress analysis in temperature variation and deformation analysis in high pressure.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.12 no.1
• /
• pp.25-32
• /
• 2008

A pin fin is optimized based on the increasing rate of heat loss by using a two-dimensional analytic method. The optimum heat loss, corresponding optimum thermal resistance and fin length are presented as a function of the fin base thickness, convection characteristic numbers ratio, fin outer radius and ambient convection characteristic number. One of the results shows that both the optimum heat loss and fin length decrease linearly whereas the optimum thermal resistance increases very slightly with increase of the fin base thickness.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.167-168
• /
• 2014

Building destruction can be occurred by decreasing of structural stability and deformation according to fire. Especially, a structural behavior of beam can be shown a slightly difference by beam types. In this paper, an evaluation of the structural stability of beam made of ordinary structural steel designed by fixed and simple boundary condition was done by an analytic method using mechanical properties of SS 400 and an heat transfer theory.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.17 no.4
• /
• pp.377-381
• /
• 1988

Effects of thermal resistance of mold during freezing processes have been investigated. Saturated liquid is chosen to present one-dimensional quasi-steady solution and this solution is compared with numerical solutions. Front tracking finite element method has been applied for the numerical solutions. Results show that mold should be considered as well as phase change material except the cases when the very thin mold with relatively high thermal conductivity is used.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.294.2-294.2
• /
• 2016

Graphene, a sigle atomic layered structure of graphite, has drawn many scientific interests for attractive future electronics and optoelectronics beyond silicon-based technology because of its robust physical, optical, and electrical properties. But high metal-graphene contact resistance prevents the successful integration of high speed graphene devices and circuits, although pristine graphene is known to have a novel carrier transport property. Meanwhile, in the recently reported metal-graphene contact studies, there are many attempts to reduce the metal-graphene contact resistance, such as doping and one-dimensional edge contact. However, there is a lack of quantitative analysis of the edge contact scheme through variously designed patterns with different metal contact. We first investigate the effets of edge contact (metal-graphene interface) on the contact resistance in terms of edge pattern design through patterning (photolithography + plasma etching) and electral measurements. Where the contact resistance is determined using the transfer length method (TLM). Finally, we research the role of metal-kind (Palladium, Copper, and Tianium) on the contact resistance through the edge-contacted devices, eventually minimizing contact resistance down to approximately $23{\Omega}{\cdot}{\mu}m$ at room temperature (approximately $19{\Omega}{\cdot}{\mu}m$ at 100 K).