• Journal of Electrochemical Science and Technology
• /
• v.2 no.1
• /
• pp.20-25
• /
• 2011

This work focuses on the behavior of the overpotential increase due to a utilization rise in a molten carbonate fuel cell. The behavior is generally explained by Nernst loss, which is a kind of voltage loss due to the thermodynamic potential gradients in a polarization state due to the concentration distribution of reactant species through the gas flow direction. The evaluation of Nernst loss is carried out with a traditional experimental method of constant gas utilization (CU). On the other hand, overpotential due to the gas-phase mass-transport resistance at the anode and cathode shows dependence on the utilization, which can be measured using the inert gas step addition (ISA) method. Since the Nernst loss is assumed to be due to the thermodynamic reasons, the voltage loss can be calculated by the Nernst equation, referred to as a simple calculation (SC) in this work. The three values of voltage loss due to CU, ISA, and SC are compared, showing that these values rise with increases in the utilization within acceptable deviations. When we consider that the anode and cathode reactions are significantly affected by the gas-phase mass transfer, the behavior strongly implies that the voltage loss is attributable not to thermodynamic reasons, namely Nernst loss, but to the kinetic reason of mass-transfer resistance in the gas phase.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.899-904
• /
• 2009

This paper presents the analysis result of load-transfer mechanism and pile movements associated with the development of frictional resistance to understand the engineering characteristics of micropile behavior. An field load tests were performed for two different types of micropiles and they are (i) thread bar reinforcement with D=50mm and (ii) hollow steel pipe reinforcement with $D_{out}$=82.5mm and $D_{in}$=60.5mm and wrapped with woven geotextile for post-grouting. The load test results indicated that micropiling with pressured grouting provided better load-transfer characteristics than micropiling with gravity grouting under both compressive and tensile loading conditions in that unit skin frictional resistance is well distributed along installation depth. The unit weight and unconfined compressive strength of cured grout were obtained for each piling method. The strength and unit weight of micropile with pressured grouting was higher than those with gravity grouting. The fact that load bearing quality with pressured grouting is better than that of gravity grouting could be attributed to the dense mutual adhesion between surrounding ground and pile due to pressurized grouting method and better grout quality.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.6
• /
• pp.59-72
• /
• 2009

The load distribution and deflection of offshore piles are investigated by lateral load-transfer curve method (p-y curve). Special attention is given to the soil-pile interaction and soil resistance of 3D wedge failure mode. A framework for determining a hyperbolic p-y curve is proposed based on theoretical analysis and experimental load test results. The methods for determining appropriate material parameters needed for constructing the proposed p-y curves are presented in this paper. Through comparisons with field case studies, it was found that the proposed method in the present study estimates reasonably the load transfer behavior of pile, and thus, the computed pile responses, such as bending moment and lateral displacement, agree well with the actual measured responses.

• Fisheries and Aquatic Sciences
• /
• v.9 no.2
• /
• pp.97-100
• /
• 2006

To determine whether the tetracycline resistance genes tet (34), tet (M), and tet (S) can be transferred among bacteria, we used a filter mating experiment allowing intimate cell-cell contact between donor and recipient. The tet(34) gene, conveyed on a chromosome of Vibrio species (No. 6 and SW-42) was not transferred to Escherichia coli JM109, suggesting that it is not transferred among bacterial species. The tet (M) gene was transferred from three Vibrio strains (4-E, SW-18, and SW-38) to E. coli at frequencies of $8.5{\times}10^{-5}\;to\;2.1{\times}10^{-6}$. The tet(S) gene was transferred from Lactococcus garvieae KHS98032 to E. coli at a frequency of $1.8{\times}10^{-6}$. Transconjugated recipients showed increased minimum inhibitory concentrations against oxytetracycline. Although the donors possess the Tn916-Tn1545 transposons, they were not detected in transformed recipients, suggesting that the transfer of tet(M) and tet(S) is mediated by elements or mechanisms. Two ribosomal protect protein genes were also transmissible from marine bacteria to E. coli, suggesting gene hopping among marine, terrestrial, and human environments.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.2
• /
• pp.179-185
• /
• 2013

The behavior of surface film formation was greatly dependent on the speed of potential cycling. In $LiClO_4$ / EC + DEC, cyclic voltammetry results showed that the peaks originated from surface film formation on graphite electrode at the high charge-discharge rate was shifted to the lower potentials as the charge-discharge rate decrease. This indicates that surface films with different morphology and thickness were formed by different charge-discharge rate. Transmission electron microscopy (TEM) results indicated that the properties such as thickness and morphology of the surface film were greatly affected by the charge-discharge rate. Electrochemical impedance spectroscopy (EIS) showed that the resistance of surface film was affected by the speed of potential cycling. In addition, the charge transfer resistance was also dependent on the charge-discharge rate indicating that the charge transfer reaction was affected by the nature of surface film. TEM and EIS results suggested that the chemical property as well as the physical property of the surface film was affected by the charge-discharge rate.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.2
• /
• pp.263-269
• /
• 2016

Temperate phages have been suggested to carry virulence factors and other lysogenic conversion genes that play important roles in pathogenicity. In this study, phage TEM123 in wild-type Staphylococcus aureus from food sources was analyzed with respect to its morphology, genome sequence, and antibiotic resistance conversion ability. Phage TEM123 from a mitomycin C-induced lysate of S. aureus was isolated from foods. Morphological analysis under a transmission electron microscope revealed that it belonged to the family Siphoviridae. The genome of phage TEM123 consisted of a double-stranded DNA of 43,786 bp with a G+C content of 34.06%. A bioinformatics analysis of the phage genome identified 43 putative open reading frames (ORFs). ORF1 encoded a protein that was nearly identical to the metallo-β-lactamase enzymes that degrade β-lactam antibiotics. After transduction to S. aureus with phage TEM123, the metallo-β-lactamase gene was confirmed in the transductant by PCR and sequencing analyses. In a β-lactam antibiotic susceptibility test, the transductant was more highly resistant to β-lactam antibiotics than S. aureus S133. Phage TEM123 might play a role in the transfer of β-lactam antibiotic resistance determinants in S. aureus. Therefore, we suggest that the prophage of S. aureus with its exotoxin is a risk factor for food safety in the food chain through lateral gene transfer.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.4
• /
• pp.560-566
• /
• 2015

The self-consistent simulation based on the drift-diffusion approximation with anisotropic transport coefficients was performed. The RHCP-wave propagation was observed in MICP and this wave was refracted toward the high-density region. The calculated impedance seen from the antenna terminal shows that resistance component of MICP is a higher than that of ordinary ICP. Because of a higher resistance, the power transfer efficiency was improved to 95%. This property is practically important for large-size, low-pressure plasma sources because high resistance corresponds to high power-transfer efficiency and stable impedance matching characteristics.

• Journal of Sensor Science and Technology
• /
• v.22 no.5
• /
• pp.315-320
• /
• 2013

In this paper, the properties of strain sensors made of spin-capable multi-walled carbon nanotubes (MWCNTs) were characterized and their sensing mechanisms analyzed. The key contribution of this paper is a new fabrication technique that introduces a simpler transfer method compared to spin-coating or dispersion CNT. Resistance of the MWCNT sheet strain sensor increased linearly with higher strain. To investigate the effect of CNT concentration on sensitivity, two strain sensors with different layer numbers of MWCNT sheets (one and three layers) were fabricated. According to the results, the sensor with a three-layer sheet showed higher sensitivity than that with one layer. In addition, experiments were conducted to examine the effects of environmental factors, temperature, and gas on sensor sensitivity. An increase in temperature resulted in a reduction in sensor sensitivity. It was also observed that ambient gas influenced the properties of the MWCNT sheet due to charge transfer. Experimental results showed that there was a linear change in resistance in response to strain, and the resistance of the sensor fully recovered to its unstressed state and exhibited stable electromechanical properties.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.333-338
• /
• 2006

This study is a research on Dual Bore heat pipe to investigate the ability of heat transport ability, heat resistance and difference of heat transport ability according to the type of heat pipes. As the result of this research, we got several conclusions. Each pipe of Dual Bore in one section has a similar heat transfer capability. In the range between $-20^{\circ}C$ and $60^{\circ}C$ the heat transfer capability is double than single bore which was analyzed by menas of GAP program. Heat resistance is below $0.05^{\circ}C$/W at every point, and it tells aluminum-ammonia heat pipes are proper for satellite.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.7
• /
• pp.642-648
• /
• 2000

Falling film heat transfer analyses with aqueous lithium bromide solution were peformed to investigate the transfer characteristics of the copper tubes. Finned(knurled) tube and a smooth tube were selected as test specimens. Averaged generation fluxes of water and the heat transfer performances(heat flux, heat transfer coefficient) were obtained. The results of this work were compared with the data reported previously. As the film flow rate of the solution increased, the generation fluxes of water decreased for both tubes. The reason is estimated by the fact that the heat transfer resistance with the film thickness increased as the film flow rate increased. The effect of the enlarged surface area at the knurled tube was supposed to be dominant at a small flow rate. The generation fluxes of water increased with the increasing degree of tube wall superheat. Nucleate boiling is supposed to occur at a wall superheat of 20 K for a smooth tube, and at 10 K for a knurled tube. The heat transfer performance of the falling film was superior to pool boiling at a low wall superheat below 10 K for both tubes tested. The knurled tube geometry showed good performance than the smooth tube, and the increased performance was mainly came from the effect of the increased heating surface area.