Hong, J. T.;Choi, Y.;Sung, J. H.;Kim, Y. K.;Lee, K. M.
Journal of Biosystems Engineering
/
v.26
no.4
/
pp.337-354
/
2001
This study was conducted in order to develop a Chinese cabbage harvester attachable to tractors. For designing Chinese cabbage harvester in which laboratory and field tests were conducted with to determine feasible values design factors. To adopt the various sizer of C-cabbages, U-type soft rubber band was attached to the chain conveyor with an angle. Required torque of the conveyor axle was about 206-210kgf$.$cm. And the required peripheral speed of the disk cutter was 6.54m/s or more to have a clean session in root cutting. Three different harvest method were tested. The best harvesting method with minimum pulling force and damage was disk cutting flying just above the soil surface were the cut chinese cabbages are transferring to the holding conveyor attached soft rubber lug in prompt. Theoretical speed ratio of the tractor travel and feed of a chain conveyor was 1:1.2 with the attaching angle of 30 degree and 1:1.1 with the angle of 20 degree. Actual field experiment showed the speed ratio of 1:1.5 was the best because of the slip effect.
This study was carried out through the survey questionaries in order to get the information for proper operating technique of the two-wheel tractors which are widely used in the farm, and investigated various accidents which occurred during the operation of two-wheel tractors for farm works in 7 Provinces of Korea. The summarized results are as follows ; 1. Annual accident frequency of the two-wheel tractor was 2.07 times, and the average rate of accident was 0.72 times per hour. Its value was the largest in the pre-operations , and the smallest in the threshing operation. 2. The accident distribution according to each month was nearly propertional to the operating hours of the two-wheel tractor. More than 60 % of total accident was concentrated during the rice transplanting and harvesting season. 3. The careless accident was more than 50% of total accident , and inevitable accident about 18% . The rate of careless accident showed the highest in pre-operation such as engine starting, check, and adjustment, and belt change. 4. The serious wounded operator was 7.1 % to total wounded operator , and about 50 % of accident of casualties to operators occurred during haruling operations. 5. The amount of casualties to property was range of 1,000 to 10,000 won, and annual total amount per unit tractor could be estimated to be 10 , 000 won.
This survey was conducted to investigate the status of repair and maintenance of 4 wheel tractor for a basic reference to the improvement of quality and proper utilization of tractors. Thirty two counties from eight provinces, except Jeju, were covered in this study in order to investigate annual break-down and repair of tractor in 1980. The analyzed results are summarized as follows; 1. The average number of break-down of large size tractors(47ps) was 5.0 times in a year and it was about twice of that of small size tractors(19-23ps). The break-down frequency per 100 hours of use was 1.11 times in the large size and 0.65 times in the small size tractors. 2. 75.6 percent of total break-down was occured in main body of tractor and 24.4 percent in attachments. In particular, the break-down of plow and rotavator was more than 80 percent of total break-down of the small size tractor attachments. 3. The large size tractors which were occured more than one times of break-down a year was 75 percent and its rate of the small size tractor was 62 percent. But 9 percent of tractor surveyed had more than ten times of break-down in a year 4. The frequency of break-down had a peak in May, and it was directly proportional to the hours of use. 5. The causes of break-down were poor maintenance and operation by 29.8 precent, old parts by 30.2 percent, poor quality of parts by 20.6 percent, poor field condition by 16.3 percent and others by 3.1 percent. 6. Annual number of repair was 5.5 times and among them 55.6 percent was done by shop and 44.4 percent by operator. 7. Total required repair time was 30.6 hours a year in the large size tractor and 19.9 hours in the small size tractor. Average repair time was 3.62 hours a time. 8. Annual repair cost was 278 thousand won in the large size tractor and 70 thousand won in the small size tractor. The repair cost per hour of use was 621 won in the large size and 198 won in the small size tractor. 9. The repair cost rate of tractor(Y) was regulated with tractor age (X) as follow; Y=0.752X In case of the service life of tractor was 10 years, the total repair cost rate was 64 percent.
Kim, Hyuck-Joo;Kim, Kwan-Woo;Choi, Sun;Kim, Jong-Sun;Kim, Yu-Yong;Kim, Jin-Oh;Kim, Hak-Kyu;Kwon, Soon-Hong
Journal of Biosystems Engineering
/
v.35
no.5
/
pp.294-301
/
2010
This study was performed to improve the utilization of the ROPS and seatbelt of tractors in Korea. We surveyed the ROPS and seatbelt use and the tractor related accidents through the personal interviews for 141 farmers. And comfort test for tractor seatbelts is done for 4 different subjects by measuring the body pressure distribution. The survey showed that 79.3% of the tractor accidents was overturning accidents. And, in case the tractor has ROPS and seatbelt, there was no serious injuries. With this results, we could confirm that ROPS and seatbelt is very effective devices for protecting drivers in overturning accidents. But, in case farmers didn't wear seatbelt, there was some fatal injuries. This shows the importance of the seatbelt use in working and driving tractors. Therefore, we tested the comfort of the tractor seatbelt for 4 different subjects operating the pedal in tractor seat simulator and in the tractor running on various roads. From the results of the static test in the Lab, it was shown that more the seatbelt anchorage point is far form SIP point, more the body pressure of the belly became higher, and more the subjects feel uncomfortable. Not only in the static test in the simulator, but also in the dynamic test in riding tractors, it was shown that non retractable seatbelt was more uncomfortable than retractable seatbelt. According to this study, we concluded that we need to promote the utilization of the ROPS and seatbelt use. And, the non retractable seatbelt need to be replaced by retractable seatbelt. Also, we recommend that the seatbelt anchorage position should to be in the seatbelt anchorage area of the ISO 3776 standard.
Shin, Seung-Yeoub;Kang, Chang Ho;Yu, Seok Cheol;Kim, Byounggap;Kim, Yu-Yong;Kim, Jin Oh
Journal of Biosystems Engineering
/
v.39
no.4
/
pp.261-266
/
2014
Purpose: This study was conducted to serve as a basis for strengthening policy support and R&D to improve the domestic and international competitiveness of domestic agricultural machinery. Levels of satisfaction among farmers and service engineers were analyzed regarding the current quality of agricultural machinery and the primary consumers' propensity for replacement purchases. Methods: A survey was carried out targeting farmers in over 150 townships and 300 villages in South Korea who collectively used 711 tractors, 286 rice transplanters, and 221 combine harvesters. Furthermore, agricultural machinery service engineers from 20 different after-services were surveyed regarding the quality of main components in domestic agricultural machinery versus those in imported agricultural machinery. Results: The farmers' overall quality satisfaction ratings for tractors, rice transplanters, and combine harvesters ranged from 57.1% to 62.6% in consideration of operating performance, failure rate, and durability. Compared with imports, satisfaction ratings for domestic agricultural machinery were 19.1%p to 38.1%p lower for quality. Regarding engines, transmissions, hydraulics, planters, reapers, threshers, and electrical components, only 5.3% to 25.0% of service engineers indicated that domestic agricultural machinery was higher in quality compared with imports. By contrast, 33.3% to 78.9% of those surveyed indicated that domestic components were lower in quality compared with imports. Intent to purchase replacement agricultural machinery at the end of their respective products' lifecycles was indicated that they planned to purchase imported tractors, rice transplanters, and combine harvesters comprised 25.2%, 46.9%, and 43.9%, respectively. This clearly shows that a very high percentage of farmers were satisfied, particularly for transplanters and combine harvesters. Conclusions: The level of desire for purchasing imported agricultural machinery was very high among those who expressed intent to purchase replacement machinery. Therefore, strong policy support and R&D for domestic agricultural machinery is critical for improving competitiveness on the domestic and foreign markets.
Hong, Soon-Jung;Ha, Jong-Kyou;Kim, Yong-Joo;Kabir, Md. Shaha Nur;Seo, Young Woo;Chung, Sun-Ok
Journal of Biosystems Engineering
/
v.43
no.1
/
pp.1-13
/
2018
Purpose: The development of compact tractors that can be used in dry fields, greenhouses, and orchards for pest control, weeding, transportation, and harvesting is necessary. The development and performance evaluation of power transmission units are very important when it comes to tractor development. This study evaluates the performance of a driving power transmission unit of a 50 kW multi-purpose narrow tractor. Methods: The performance of the transmission and forward-reverse clutch, which are the main components of the driving power transmission unit of multi-purpose narrow tractors, was evaluated herein. The transmission performance was evaluated in terms of power transmission efficiency, noise, and axle load, while the forward-reverse clutch performance was evaluated in terms of durability. The transmission's power transmission efficiency accounts for the measurement of transmission losses, which occur in the transmission's gear, bearing, and oil seal. The motor's power was input in the transmission's input shaft. The rotational speed and torque were measured in the final output shaft. The noise was measured at each speed level after installing a microphone on the left, right, and upper sides. The axle load test was performed through a continuous equilibrium load test, in which a constant load was continuously applied. The forward-reverse clutch performance was calculated using the engine torque to axle torque ratio with the assembled engine and transmission. Results: The loss of power in the transmission efficiency test of the driving power unit was 6.0-9.7 kW based on all gear steps. This loss of horsepower was equal to 11-18% of the input power (52 kW). The transmission efficiency of the driving power unit was 81.5-89.0%. The noise of the driving power unit was 50-57 dB at 800 rpm, 70-77 dB at 1600 rpm, and 76-83 dB at 2400 rpm. The axle load test verified that the input torque and axle revolutions were constant. The results of the forward-reverse clutch performance test revealed that hydraulic pressure and torque changes were stably maintained when moving forward or backward, and its operation met the hydraulic design standards. Conclusions: When comprehensively examined, these research results were similar to the main driving power transmission systems from USA and Japan in terms of performance. Based on these results, tractor prototypes are expected to be created and supplied to farmhouses after going through sufficient in-situ adaptability tests.
This paper focuses on measuring the efficiency of container yards in container terminals in Busan and Gwangyang using Data Envelopment Analysis (DEA) approach. It analyses the relative efficiency of 11 container terminals based on the data for the period between 2006 and 2009 to offer a fresh perspective. The applied framework assumes inputs to be container cranes, transtainer cranes and yard tractors and output as container transshipment volume. Through the analysis, the differences between the impact of using of container cranes, transtainer cranes and yard tractors, top handler & reach stacker on container yard efficiency are measured. Moreover, the associations between the three input factors are analyzed as well. This paper also employs heteroscedastic Tobit model to show the impact of explanatory variables on container yard efficiencies. I took into consideration the strategies for operation of container cranes, transtainer cranes and yard tractors in container yard.
As part of measures to reduce fine dust, the government is promoting a project to convert the fuel of Yard Tractors(YT, tractors operated at ports), from diesel to LNG (Liquefied Natural Gas). While a port having a small number of yard tractors, it is not proper to construct a stationary LNG fueling station and supply LNG to YT due to a problem of BOG (Boil off gas) generation. Therefore, it is necessary to make a regulation and a standard on mobile LNG YT refueling station installation and inspection as an alternative. In this study, we have investigated domestic and foreign mobile LNG refueling cases and refueling standards, including the USA and Europe. In addition, we have suggested the risk reduction method according to the cause after investigation of the cause of LNG accidents. And last, based on the proposed risk reduction measures, we have proposed an amendment to the Regulation of the Urban Gas Business Law in Korea. The proposed mobile LNG YT refueling amendment of the Regulation includes ; maintenance of the safety distance from the protection facility, installation of an interlock device to prevent refueling in places other than the authorized place, installation of the identification system through biometrics, separation of the tank lorry and tow vehicle before refueling, checking the wheel fixed status of tank lorry before refueling, construction of the impounding area, safety measures before, during and after refueling, etc. The safety standards proposed in this study could be used as a reference in establishing standards for mobile LNG vehicle refueling in the near future.
Proceedings of the Korean Society for Agricultural Machinery Conference
/
2003.02a
/
pp.278-283
/
2003
트랙터 작업은 일반적으로 부하의 변동이 크기 때문에 잦은 변속이 요구되며, 견인 또는 다양한 작업기의 구동 등 작업 조건에 따라 적합한 작업 속도를 얻기 위한 많은 변속 단수가 요구된다. 이러한 특성 때문에 트랙터의 변속기는 큰 견인 부하에서도 정지하지 않고 원하는 속도로 원활하게 변속할 수 있어야 하며 동시에 동력 손실을 최소화할 수 있어야 한다 따라서, 트랙터 변속 장치는 작업 능률과 전동 효율을 동시에 고려할 경우, 작업 능률이 놀은 유압 변속과 동력 전달 효율이 놀은 기계식 동력 전달을 조합한 파워시프트 변속이 가장 우수한 것으로 판단된다. (중략)
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.