• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2015년도 추계학술대회
• /
• pp.37-39
• /
• 2015

The ships transiting the Northern Sea Route (NSR) have been gradually increased so that the number of ship-ice collision accidents would be increased. The collision between ship and ice floe can lead to serious damage of hulls and decline of ship's maneuverability. In this study, collision tests that a model ship is forced to collide with disk-shaped synthetic ice floes are conducted in a towing tank. The synthetic ice floes made of polypropylene which has similar density with real ice are used. The ice load is measured by a load cell installed on the carriage rod. The ice floe's motion is measured by a motion sensor installed on the synthetic ice floe. The influences of contact conditions such as hull form and ship speed on the ship-ice collision response are investigated and discussed by measured peak force and ice floe's motion.

• 대한조선학회논문집
• /
• 제50권4호
• /
• pp.240-247
• /
• 2013

Hydrodynamic characteristics of a planing craft are very sensitive to the hull form variations, especially when the craft navigates with high-speed. Therefore, we need to verify hydrodynamic performances of the craft during the process of hull form design. In this paper, motion performances of a 40ft class cruise leisure boat are evaluated by both model tests and theoretical analyses using two different methods. Model tests are carried out at calm sea and regular wave conditions using high speed towing carriage installed in SNU towing tank. Theoretical methods used are a empirical method proposed by Martin (1976) and a potential method based on Rankine panel (DNV, 2010). The results from the theoretical methods are compared with and verified by those of model tests. Results of empirical formula showed somewhat larger motion RAOs and resonant frequencies than those of model tests. Potential based method showed even larger discrepancies with the model test results. From the analyses of comparison results, we could confirm the limitation of each theoretical method and suggest the way of improvement for the better prediction of motion performances.

• 해양환경안전학회지
• /
• 제13권4호
• /
• pp.71-78
• /
• 2007

예부선은 항만 개발 및 매립, 해상교량 건설, 항로 준설 등 우리나라 해양 산업 건설에 핵심적인 공헌과 역할을 수행하여 왔다. 또한 국내 등록 척수로는 가장 많은 비중을 차지하고 있고, 부선의 경우 전용화와 대형화가 꾸준히 진행되어 일반 상선과 등급의 부선이 운항되고 있다. 이로 인한 해양사고의 증가에도 불구하고 예부선에 대한 국가적인 차원에서의 안전운항 대책이 미흡한 실정이다. 본 연구는 최근 빈번하게 발생하고 있는 해상교량과 관련된 예부선의 사고에 대한 안전 운항 대책을 제안하고자 한 것으로, 해양사고의 통계 자료와 사례 분석, 예부선 운항 실태를 운송계약 측면과 인원 구성을 검토하여 해상교량의 안전 통항을 위해 선학 자체적으로 점검해야 하는 항해계획과 운항점검표를 일례로 제시하고, 예부선의 안전운항 향상을 위한 전자차트시스템 기반의 안전항행지원시스템을 제안한다.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.691-698
• /
• 2020

In this study, the effects of hydrodynamic interceptors on a high-speed vessel were investigated to identify the operating principle based on experiments. Model tests were performed using a high-speed towing carriage. The resistance, trim and rise of Center of Gravity (CG) of the high-speed vessel were measured for various ship speeds and interceptor heights. As the interceptor height increased, the trim and rise of CG were reduced. In order to quantitatively analyze these phenomena, the pressure at the stern bottom was measured using tactile sensors. The reliability of the measured results from the tactile sensors was verified through repeat tests. The pressure on the stern bottom increased in proportion to the interceptor height, as the interceptor partially blocked the flow there. Then, the trim was reduced. However, as the ship speed increases, the pressure at the location close to the interceptor decreases when the interceptor height is small, leading to increased trim. Therefore, the interceptor height for running attitude control should be carefully determined considering multiple factors in the operating condition of the high-speed planing hull.

• 한국항해항만학회지
• /
• 제31권10호
• /
• pp.813-818
• /
• 2007

선박의 선형시험설비로는 회류수조, 예인수조 등이 있으나, 소형 고속선박은 실선 대응 모형선의 축적비가 대형선에 비해 매우 작고 수조의 유속과 예인전차의 속도제한으로 고속선의 설계선속까지의 성능검증에는 한계로 작용하였다. 이에, 고속 활주형선의 선형시험 검증을 위해 실 해상모형시험기법을 정립하였다. 한편, 고속 Stepped Hull선형은 일체형 활주형 선저선형에 비하여 고속 주행시 공기공급에 따른 접수면 감소로 인하여 저항감소에 따른 속도향상과 연비절감 효과가 있으나, 선미 좌우측의 접수면 감소에 따른 횡동요 안정성이 감소되는 경향이 있다. 이에, 본 논문에서는 고속 선형시험이 가능한 해상모형시험을 이용하여 선미 보조동체 장착 유무에 따른 고속 Stepped Hull 선형의 횡동요 및 저항특성을 비교, 분석한 것이다.

• 대한조선학회논문집
• /
• 제59권1호
• /
• pp.39-45
• /
• 2022

Normal strategy of structure optimization procedure has been minimum cost or weight design. Minimum weight design satisfying an allowable stress has been used for the ship and offshore structure, but minimum cost design could be used for the case of high human cost. Natural frequency analysis and forced vibration one have been used for the strength estimation of marine structures. For the case of high precision experiment facilities in marine field, the structure has normally enough margin in allowable stress aspect and sometimes needs high natural frequency of structure to obtain very high precise experiment results. It is not easy to obtain a structure design with high natural frequency, since the natural frequency depend on the stiffness to mass ratio of the structure and increase of structural stiffness ordinary accompanies the increase of mass. It is further difficult at the grillage structure design using the profiles, because the properties of profiles are not continuous but discrete, and resource of profiles are limited at the design of grillage structure. In this paper, the grillage structure design system under the constraint of high natural frequency is introduced. The design system adopted genetic algorithm to realize optimization procedure and can be used at the design of the experimental facilities of marine field such as a towing carriage, PMM, test frame, measuring frame and rotating arm.