Browse > Article
http://dx.doi.org/10.1016/j.ijnaoe.2020.08.003

An experimental study on the stern bottom pressure distribution of a high-speed planing vessel with and without interceptors  

Seok, Woochan (Research Institute of Marine Systems Engineering, Seoul National University)
Park, Sae Yong (Department of Naval Architecture and Ocean Engineering, Seoul National University)
Rhee, Shin Hyung (Research Institute of Marine Systems Engineering, Seoul National University)
Publication Information
International Journal of Naval Architecture and Ocean Engineering / v.12, no.1, 2020 , pp. 691-698 More about this Journal
Abstract
In this study, the effects of hydrodynamic interceptors on a high-speed vessel were investigated to identify the operating principle based on experiments. Model tests were performed using a high-speed towing carriage. The resistance, trim and rise of Center of Gravity (CG) of the high-speed vessel were measured for various ship speeds and interceptor heights. As the interceptor height increased, the trim and rise of CG were reduced. In order to quantitatively analyze these phenomena, the pressure at the stern bottom was measured using tactile sensors. The reliability of the measured results from the tactile sensors was verified through repeat tests. The pressure on the stern bottom increased in proportion to the interceptor height, as the interceptor partially blocked the flow there. Then, the trim was reduced. However, as the ship speed increases, the pressure at the location close to the interceptor decreases when the interceptor height is small, leading to increased trim. Therefore, the interceptor height for running attitude control should be carefully determined considering multiple factors in the operating condition of the high-speed planing hull.
Keywords
High-speed planing hull; Pressure measurement; Tactile sensor; Interceptor;
Citations & Related Records
Times Cited By KSCI : 4  (Citation Analysis)
연도 인용수 순위
1 Shtessel, Y.B., Shkolnikov, I.A., Levant, A., 2009. Guidance and control of missile interceptor using second-order sliding modes. IEEE Trans. Aero. Electron. Syst. 45 (1), 110-124.   DOI
2 Smiley, R.F., 1951. An Experimental Study of Water-Pressure Distributions during Landing and Planing of a Heavily Loaded Rectangular Flate-Plate Model (No. NACA-TN-2453). National Aeronautics and Space Administration.
3 Tsai, J.F., Hwang, J.L., 2004. Study on the compound effects of interceptor with stern flap for two fast monohulls. In: Proceedings of the IEEE Xplore Conference: Oceans' 04 MTS/IEEE Techno-Ocean'04, vol. 2, pp. 1023-1028.
4 Brizzolara, S., Villa, D., 2009. A systematic CFD analysis of flaps/interceptors hydrodynamic performance. In: Proceedings of 10th International Conference on Fast Sea Transportation, Athens, Greece.
5 De Luca, F., Pensa, C., 2017. The Naples warped hard chine hulls systematic series. Ocean. Eng. 139, 205-236.   DOI
6 Cusanelli, D., Karafiath, G., 1997. Integrated wedge-flap for enhanced powering performance. In: Proceedings of Fourth International Conference on Fast Sea Transportation, Sydney, Australia.
7 Day, A.H., Cooper, C., 2011. An experimental study of interceptors for drag reduction on high-performance sailing yachts. Ocean. Eng. 38 (8-9), 983-994.   DOI
8 De Luca, F., Pensa, C., 2012. Experimental investigation on conventional and unconventional interceptors. Int. J. Small Craft Technol. 154, 65-72.
9 Evdokimenkov, V.N., Krasilshchikov, M.N., Lyapin, N.A., 2018. Guaranteeing UAV trajectory control when approaching a maneuvering air target. J. Comput. Syst. Sci. Int. 57 (5), 789-800.   DOI
10 Garme, K., Rosen, A., Kuttenkeuler, J., 2010. In Detail Investigation of Planing Pressure. Proceedings of HYDRALAB III Joint User Meeting, Hannover, Germany.
11 Ghadimi, P., Loni, A., Nowruzi, H., Dashtimanesh, A., Tavakoli, S., 2014. Parametric study of the effects of trim tabs on running trim and resistance of planing hulls. Adv. Shipp. Ocean. Eng. 3, 1-12.
12 Avci, A.G., Barlas, B., 2019. An experimental investigation of interceptors for a high speed hull. Int. J. Nav. Architect. Ocean. Eng. 11 (1), 256-273.   DOI
13 Benedict, R.P., 1985. ASME measurement uncertainty. J. Fluid Eng. 107, 161-164.   DOI
14 Maki, K.J., 2006. Transom Stern Hydrodynamics. PhD Thesis. University of Michigan.
15 Ikeda, Y., Katayama, T., 2000. Stability of High Speed Craft. Contemporary Ideas on Ship Stability, pp. 401-409.
16 Kim, D.J., 2012. A Study on the Running Attitude and Dynamic Stability of a Semi-displacement Round Bilge Vessel at High Speed. Ph.D. thesis. Seoul National University, Seoul, Korea.
17 Kim, D.J., Kim, S.Y., You, Y.J., Rhee, K.P., Kim, S.H., Kim, Y.G., 2013. Design of highspeed planing hulls for the improvement of resistance and seakeeping performance. Int. J. Nav. Architect. Ocean. Eng. 5 (1), 161-177.   DOI
18 Mansoori, M., Fernandes, A.C., 2016. The interceptor hydrodynamic analysis for controlling the porpoising instability in high speed crafts. Appl. Ocean Res. 57, 40-51.   DOI
19 Molini, A., Brizzolara, S., 2005. Hydrodynamics of interceptors: a fundamental study. In: Proceedings of the International Conference on Marine Research and Transportation, vol. 1. ICMRT, Ischia, Italy.
20 Santoro, N., Begovic, E., Bertorello, C., Bove, A., De Rosa, S., Franco, F., 2014. Experimental study of the hydrodynamic loads on high speed planing craft. Procedia Eng. 88, 186-193.   DOI
21 Grigoropoulos, G.J., Damala, D.P., 2001. Measurement of bottom pressures on planing craft. WIT Trans. Model. Simulat. 30.
22 Seo, J., Choi, H.K., Jeong, U.C., Lee, D.K., Rhee, S.H., Jung, C.M., Yoo, J., 2016. Model tests on resistance and seakeeping performance of wave-piercing high-speed vessel with spray rails. Int. J. Nav. Architect. Ocean. Eng. 8 (5), 442-455.   DOI
23 Savitsky, D., 1992. Overview of planing hull developments. In: Proceedings of Intersociety High Performance Marine Vehicle Conference and Exhibit. June, Arlington, Texas.
24 Savitsky, D., Gore, J.L., 1980. Re-evaluation of the planing hull form. J. Hydronautics 14 (2), 34-47.   DOI