• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.451-461
• /
• 2010

Electric vehicles (EVs) require fast torque response and high drive efficiency. This paper describes a control scheme of fuzzy direct torque control of permanent magnet synchronous motor for EVs. This control strategy is extensively used in EV application. With direct torque control (DTC), the electromagnetic torque and stator flux can be estimated using the measured stator voltages and currents. The estimation depends on motor parameters, except for the stator resistance. The variation of stator resistance due to changes in temperature or frequency downgrades the performance of DTC, which is controlled by introducing errors in the estimated flux linkage vector and the electromagnetic torque. Thus, compensation for the effect of stator resistance variation becomes necessary. This work proposes the estimation of the stator resistance and its compensation using a proportional-integral estimation method. An electronic differential has been also used, which has the advantage of replacing loose, heavy, and inefficient mechanical transmission and mechanical differential with a more efficient, light, and small electric motors that are directly coupled to the wheels through a single gear or an in-wheel motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.803-806
• /
• 1997

In this paper, a force estimation method is proposed for the sensorless force control. For this, a disturbance observer is applied to each joint of an n degrees of freedom manipulator to obtain a simple equivalent robot dynamics(SERD) being represented as an n independent double integrator system. To estimate the output of disturbance observer in the absence of external force, the observer estimator is designed, where the uncertain parameters of the robot manipulator are adjusted by gradient method to minimize the output between the disturbance observer and the observer estimator. When the external force is exerted, the external force is estimated using the difference between the output of disturbance observer which include the external torque signal and that of observer estimator. And then, a force controller is designed for force feedback control employing the estimated force signal. To verify the effectiveness of the proposed force estimation method, several numerical examples are illustrated for the 2-axis planar type robot manipulator.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.219-224
• /
• 2001

An accurate tip position control of a single-link flexible manipulator subjected to torque disturbance is achieved by utilizing so called sliding mode controller with disturbance estimation (SMCDE). After formulating the governing equation of motion in the state 1pace representation, a stable sliding surface is designed via the LQR method. The SMCDE is then synthesized by integrating equivalent sliding mode controller with the disturbance estimator which is featured by an integrated average value of the imposed disturbance over a certain sampling period. The regulating tip motion of the flexible manipulator is evaluated by employing the proposed SMCDE.

• 전력전자학회논문지
• /
• 제14권4호
• /
• pp.268-277
• /
• 2009

본 논문은 DTC-PWM을 적용한 PMSM의 속도제어 방식을 제안한다. 제안된 DTC-PWM은 기존의 DTC 방식과 PWM을 결합한 방식으로 스위칭 신호를 발생하는 구조를 가진다. 제안된 방식에서 실제 토크는 기존의 DTC 방식과 같이 추종되지만, 스위칭 신호는 토크 오차와 제어규칙에 따라 PWM 방식으로 제어한다. 토크와 자속을 제어하기 위한 스위칭 신호는 하나의 유효전압벡터와 영전압벡터로 구성되는 비대칭 스위칭 방식이 적용된다. 제안된 방식은 SVPWM과 같이 복잡한 계산없이 간단한 PWM의 연산으로 제어기를 구성하여 토크와 자속을 연속적으로 제어할 수 있다. 제안된 방식은 PMSM의 속도 제어 실험을 통하여 그 성능을 검증하였다.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.38-46
• /
• 2011

This paper presents roll angle estimator which used Kalman filter. Recently, the uses of the ELSD (Electronic Limited Slip Differential) and TVD(Torque Vectoring Differential) for vehicle yaw control are studied in many researches. However the roll angle can be negative effect of ELSD and TVD control. Therefore the information of roll angle can be used for vehicle yaw control. Moreover it can be used for rollover prevent control. Recently, most of the vehicles use lateral acceleration and yaw rate sensor. In this paper, design of Kalman filter which used lateral acceleration and yaw rate information is developed. In this paper, in order to verify the estimator ability, the CarSim and Matlab/Simulink are used.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.260-262
• /
• 1998

A new method of induction motor drive, which requires not shaft encoder, is presented. This system has both torque and speed controls that are performed by vector control. The scheme is on the basis of a rotor flux speed control, which is performed by torque producing current and rotor flux, derived from the stator voltages and currents. But, there is a problem with respect to the calculated rotor flux vector, which is an integrating operation by which the rotor induced voltage is converted into the rotor flux. The calculated rotor flux does not work so that it is unstable in initial operation, as motor speed approaches zero. For the proposed rotor flux estimator, a lag circuit is employed, to which both the motor-induced voltage and rotor flux command are imposed, and it is possible to calculate even a low frequency down to standstill. We show the validity of the proposed control method through several computer simulations.

• Journal of Electrical Engineering and Technology
• /
• 제9권2호
• /
• pp.550-558
• /
• 2014

Direct Torque controlled induction motor (DTC-IM) drives use stator resistance of the motor for stator flux estimation. So, stator resistance estimation properly is very important for a stable and effective operation of the induction motor. Stator resistance variations because of changing in temperature make DTC operation difficult mainly at low speed. A method based on artificial neural network (ANN) to estimate the stator resistance online of IM for DTC drive is modeled and verified in this paper. To train the neural network a back propagation algorithm is used. Weight adjustment of neural network is done by back propagating the error signal between measured and estimated stator current. An extensive simulation has been carried out in MATLAB/SIMULINK to prove the efficacy of the proposed stator resistance estimator. The simulation & experimental result reveals that proposed method is able to obtain precise torque and flux control at low speed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.148-151
• /
• 1991

This paper describes the vector control system estimates rotor speed based on MRAS(Model Reference Adaptive Control) and this estimate is used for speed feedback control. The stability of speed estimator is proved on the basis of hyperstability theory. In order to improve the performance of speed control, the load torque is estimated by load torque observer and speed controller compensates this estimate value. Thus the robust vector control system against load torque disturbance is constructed.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.214-219
• /
• 2003

This paper includes real-time tractive force estimation method using standard vehicle sensors such as wheel speed, brake pressure, throttle position, engine speed, and transmission carrier speed sensor. Engine map, torque converter lookup table, shaft torque observer, and brake gain adaptation method are used to estimate the tractive force. To verify this estimator, measurement which uses strain-based brake torque sensor and estimation results are presented. All results was performed using a real vehicle in a real-time.

• 한국산학기술학회논문지
• /
• 제7권4호
• /
• pp.575-579
• /
• 2006

본 논문에서는 전동기 시스템의 극저속 영역에서 안정적이고 동특성이 우수한 운전을 하기 위해 전차원상태 관측기로부터 추정되는 속도정보를 입력으로 하는 최소차원 토크 관성관측기를 구성하여 부하외란과 관성을 피드포워드 제어를 함으로써 극저속영역에 대한 강인성을 갖도록 한다. 제시한 제어 알고리즘을 MATLAB SIMULINK를 통해 전체 시스템을 모델링하고 실험을 통해 극저속에서 속도 추정 능력이 향상됨을 확인 한다.