• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.245-250
• /
• 1999

The experimental study of die-sinking electrical discharge machining for alloy tool steel of STD-11 with circular electrode was conducted for various conditions of the peak current and duty factor with the change of internal size of electrode for distributing the amount of dielectric flow through the electrode. From this study, the material removal rate(MRR) was found to be increased with the peak current and duty factor. The more MRR was obtained for the case of electrode inside diameter of 10mm. The surface roughness and roundness values were analyzed regularity under various conditions, and these values were not affected by the inside diameter change of electrode.

• Journal of the Korea Society for Simulation
• /
• v.1 no.1
• /
• pp.87-102
• /
• 1992

This paper presents the development of event-driven system level simulation tool SMPLE(Smpl Extende, an extention fo smpl) and its application to the performance analysis of multiprocessor computer systems. Because of its data structure, it is very difficult to change, expand or add new functions to simulation language smpl implemented by MacDougall. In SMPLE, we change data structure with structure and pointer, add new functions, and enable dynamic memory management. Using new data structure, facilities, and functions added in SMPLE, we simulate job processing of a shared bus multiprocessor system with autonomous hierarchical I/O subsystem. We set system performance contribution of subsystems and units. The impact of disk I/O on system performance is evaluated under vairous conditions of number of processors, processing power, memory access time and disk seek time.

• Journal of Korea Water Resources Association
• /
• v.42 no.10
• /
• pp.877-889
• /
• 2009

This study is to assess the future potential impact of climate change on stream water quality for a 6,581.1 km$^2$ dam watershed using SWAT (Soil and Water Assessment Tool) model. The ECHAM5-OM climate data of IPCC (The Intergovernmental Panel on Climate Change) A2, A1B, and B1 emission scenarios were adopted and the future data (2007-2099) were corrected using 30 years (1977-2006, baseline period) weather data and downscaled by Change Factor (CF) method. After model calibration and validation using 6 years (1998-2003) observed daily streamflow and monthly water quality (SS, T-N, and T-P) data, the future (2020s, 2050s and 2080s) hydrological behavior and stream water quality were projected.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.1-5
• /
• 1997

The plane surface rolling, one of the plastic working process, good surface condition due to increase of surface roughness and hardness. It is well known that mechanism of surface rolling depends upon rolling conditions such as rolling speed, contact pressure, step length of rolling, the shape of roller and mechanical properties of material. In this study, the optimal value of the above parameter on the surface roughness were investigated by using the rolling tool with NACHI 6000ZZ ball bearing outer races on machine structure carbon steel[SM45C]

• Genomics & Informatics
• /
• v.5 no.3
• /
• pp.137-139
• /
• 2007

RAN-aCGH is an R GUI tool for the analysis and visualization of array comparative genomic hybridization (array-CGH) experiments. The tool consists of data-loading, preprocessing for missing data, several methods for statistical identification of DNA copy number aberration, and visualization of the copy number change. RAN-aCGH requires a single input format, provides various visualizations, and allows the addition of a new statistical method, all in a user-friendly graphic user interface (GUI).

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.170-173
• /
• 2006

Requirement management is an essential process that has a significant influence on the project success. Due to the evolutionary development nature of requirement, the effective management for requirement must include change process and configuration control. This paper describes how to implement effective requirement management process to the Korea Tilting Train eXpress development with the application of a model based systems engineering tool.

• Journal of Environmental Science International
• /
• v.20 no.6
• /
• pp.789-798
• /
• 2011

Climate change assessment, together with climate change adaptation process, would be one of the worldwide important issues, and the study on climate change vulnerability indicator has been an essential problem for climate change adaptation. Vulnerability indicator can be used as a good tool to estimate the impact of climate change and to map out the distribution of its vulnerability over the given area both in Korea and other countries. This study addressed the conceptual summary on the assessment of climate change and its adaptation process. Previous studies on how to yield the vulnerability indicators of climate change are reviewed and several previous results of vulnerability indicators applied to Korean provinces are also discussed here.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.162-168
• /
• 2008

In this paper, we analyzed the heat transfer phenomenon and the reset current variation of PRAM device with thickness of phase change material using the 3-D finite element analysis tool. From the simulation, Joule's heat was generated at the contact surface of phase change material and bottom electrode of PRAM. As the thickness of phase change material was decreased, the reset current was highly increased. In case thickness of phase change material thin film was $200\;{\AA}$, heat increased through top electrode and reset current caused by phase transition highly increased. And as thermal conductivity of top electrode decreased, temperature of unit memory cell was increased.

• Journal of Climate Change Research
• /
• v.3 no.1
• /
• pp.13-24
• /
• 2012

CCGIS (Climate Change Adaptation Toolkit based on GIS) was developed to use as a tool for the climate change assessment and any relevant tasks involving climate change adaptation policy over Korean peninsula. The main objective of CCGIS is to facilitate an efficient and relevant information for the estimation of climate change vulnerability index by providing key information in the climate change adaptation process. In particular, the atmospheric modeling system implemented in CCGIS, which is composed of climate and meteorological numerical model and the atmospheric environmental models, were used as a tool to generate the climate and environmental IPCC SRES (A2, B1, A1B, A1T, A1FI, and A1 scenarios) climate data for the year of 2000, 2020, 2050, and 2100. This article introduces the components of CCGIS and describes its application to the Korean peninsula. Some examples of the CCGIS and its use for both climate change adaptation and estimation of vulnerability index applied to Korean provinces are presented and discussed here.

• Journal of Welding and Joining
• /
• v.29 no.6
• /
• pp.56-64
• /
• 2011

Friction stir spot welding between 5454 aluminum alloy sheets with the different thicknesses of 1.4 and 1.0 mm was performed. In the welding process, the tool for welding was rotated ranging from 500 to 2500, and plunged to the depth of 1.8 mm under a constant tool plunge speed of 100 mm/min. And then, the rotating tool was maintained at the plunge depth during the dwell time ranging from 0 to 7 sec. The pull-out speed of the rotating tool was 100 mm/min. The increase of tool rotation speed resulted in the change of the macrostructure of friction-stir-spot-welded zone, especially the geometry of welding interface. The results of the tensile shear test showed that the total displacement and toughness of the welds were increased with the increase of the tool rotation speed, although the maximum tensile shear load was decreased. However, the change in the dwell time at the plunge depth of the tool did not produce the remarkable variation in the macrostructure and mechanical properties of the welds. In all cases, the average hardness in friction-stir-spot-welded zone was higher than that of the base metal zone. By the friction stir spot welding technique, the welds with the excellent mechanical properties than the mechanically-clinched joints could be obtained.