• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.95-103
• /
• 2003

Driving safety of a vehicle is largely influenced by the damper and the tire. Developed in this research is a fault diagnosis algorithm for the two components so that the driver can be promptly informed when fault occurs in one or both of them. To this end, the damper and the tire were modeled using the neural network from their experimental data, and fault diagnosis was made using frequency responses of the damping force and the dynamic wheel force. The algorithm was tested via experiments, and it demonstrated successful diagnostic performance under various driving conditions.

• 한국수산과학회지
• /
• 제26권1호
• /
• pp.31-40
• /
• 1993

This paper deals with static tension analysis method for Floating Tire Breakwater(FTB). FTB can be used for the limited wave height. It is especially focused on Goodyear type FTB easily applied to the breakwater for the fisheries cultivating region. The numerical examples for FTB design procedure was reviewed. It is also studied the static analysis method of offshore catenary spread mooring system. The general calculation procedure for the tension versus excursion curves for the multi-line system using the basic catenary relationship was studied. Calculation results showed good agreement with some existing mooring results. To extend this mooring force calculating method to the floating fisheries caitivating cages, the strength of synthetic fiber was considered. This analysis method can be used to the estimation of the mooring force for the floating structures such as floating breakwaters and floating artificial reefs.

• 한국자동차공학회논문집
• /
• 제23권4호
• /
• pp.361-370
• /
• 2015

There will inevitably be errors and uncertainties in tire yaw mark related critical speed formula, which is derived merely from the relationship between the centrifugal force and the friction force acting on the point-mass vehicle. Constructing and measuring yaw marks through appropriate simulation works have made it possible to perform uncertainty analysis in calculation of critical speeds under variation of variety of conditions and parameters while existing yaw mark experimental tests have not performed properly. This paper does not present only the critical speed analysis results for parametric sensitivity and uncertainty of chord and middle ordinate, coefficient of friction and road grade, but also modeling uncertainty such as variation of braking level during turning and vehicle size. The yaw mark analysis methods and results may be now applied in practice of traffic accident investigation.

• 한국산학기술학회논문지
• /
• 제9권6호
• /
• pp.1535-1540
• /
• 2008

본 논문은 실험실에서 개발된 테스트 장치를 사용하여 여러 고무의 마찰 마모 특성을 실험적 연구에 의해 분석하였다. 마찰 계수는 하중과 온도 등과 같은 여러 가지 속도 조건 하에서의 마찰력과 측정된 수직하중으로부터 계산되었다. 자동차에 사용되는 타이어는 여러 가지 작동 상태에 따라 마찰 특성의 관계가 확인되었다.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.104-112
• /
• 2006

The influence of tire belt angle on the Plysteer Residual Aligning Torque(PRAT) and the cornering stiffness by the FEM has been studied. The PRAT is a performance factor of the tire about vehicle pull, and the cornering stiffness has relation to vehicle steering response of outdoor test. To validate FE model for analysis, simulation data for both the static stiffness(vertical, lateral) and the PRAT have been compared with the experimental data. In addition to the characteristics of the PRAT and the cornering stiffness due to the tire belt angle, rolling and cornering contact characteristics have been studied. The tendency of the PRAT and the cornering stiffness due to the belt angle can be used as a guide line for the tire design in relation to vehicle pull and vehicle steering response.

• 제어로봇시스템학회논문지
• /
• 제17권4호
• /
• pp.313-320
• /
• 2011

Multi-axle driving vehicles that are used in special environments require high driving performance, steering performance, and stability. Among these vehicles, 6WS/6WD vehicles with middle wheels have structural safety by distributing the load and reducing the pitch angle during rapid acceleration and braking. 6WS/6WD vehicles are favored for military use in off road operations because of their high maneuverability and mobility on extreme terrains and obstacles. 6WD vehicles that using in-wheel motor can generate the independent wheel torque without other mechanical parts. Conventional vehicles, however, cannot generate an opposite driving force at each side wheel. Using an independent steering and driving system, six-wheel vehicles can show better performance than conventional vehicles. Using of independent steering and driving system, the 6 wheel vehicle can improve a performance better than conventional vehicle. This vehicle enhances the maneuverability under low speed and the stability at high speed. This paper describes an independent 6WS/6WD vehicle, consists of three parts; Vehicle Model, Control Algorithm for 6WS/6WD and Simulation. First, vehicle model is application of TruckSim software for 6WS and 6WD. Second, control algorithm describes the optimum tire force distribution method in view of energy saving. Last is simulation and verification.

• 한국산업융합학회 논문집
• /
• 제2권2호
• /
• pp.173-180
• /
• 1999

When Automobile runs high velocity, it causes sleepy velocity profile then that generates lift force and drag force. Lift force reduce tire friction force. Drag force increase consumed power. For improve automobile performance, reduction of Lift force and Drag force was seriously considered. It measured experimently using wind tunnel, numerically using numerical analysis. Finite difference method is using difference equation and simplifed mesh. This method require less calculation time and computer power than other method.

• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.207-213
• /
• 1999

In this study, the possibility of estimation of friction coefficient between tire and road surface using running car data are checked. To get necessary data, such as tire and car velocities and braking force, a test car is driven with certain magnitude of decelerations from pre-set initial velocities to stop . The data are used to estimate friction coefficient with property chosen parameters , e.g,, driving stiffness, pressure distribution functions, etc. Experimental results show that running data car be used with properly chosen parameters to estimate friction coefficient.

• 접착 및 계면
• /
• 제4권1호
• /
• pp.28-34
• /
• 2003

강철 타이어 코드의 접착력 향상을 위하여 아세틸렌 플라즈마 중합 코팅, 아르곤 에칭+아세틸렌 플라즈마 중합 코팅, 그리고 아르곤 에칭+담채를 이용한 아세틸렌 플라즈마 중합 코팅을 실시하였으며, 접착력은 TCAT시편으로 측정하였다. 플라즈마 중합 코팅된 타이어 코드의 내구성을 고찰하기 위하여 제 1 단계로 아세틸렌 플라즈마 중합 코팅된 타이어코드를 상온에서 1, 3, 5, 10, 15일 동안 방치한 후 TCAT 시편을 제조하여 접착력변화를 측정하였으며, 제 2 단계로는 플라즈마 중합 코팅된 코드로 TCAT 시편을 제조한 후 증류수, 10% NaCl 수용액에서 또는 $100^{\circ}C$ 오븐에서 1, 2, 3, 4주간 노화시키면서 접착력 변화를 측정하였다. SEM/EDX을 이용하여 코드의 파괴표면을 분석하였으며, 황동코팅과 비교 분석하였다. 아르곤 에칭+담채를 이용한 아세틸렌 플라즈마 중합으로 코팅된 강철 타이어 코드의 접착력은 황동코팅된 시편의 접착력과 거의 같은 수준이었다. 타이어 코드의 상온 노화시험에서 황동코팅된 시편이 아세틸렌 플라즈마 중합 코팅된 시편에 비하여 우수 내구성을 보여주었으나, TCAT 시편의 노화에서는 아세틸렌 플라즈마 중합 코팅이 황동코팅에 비하여 우수하거나 비슷한 결과를 보였다.

• 한국소음진동공학회논문집
• /
• 제23권2호
• /
• pp.176-184
• /
• 2013

Quantification of road noise is a challenging issue in the development of tire noise since its transfer paths are complicated. In this paper, a simplified model to estimate the road noise is developed. Transfer path of the model is from wheel to interior. The method uses the wheel excitation force estimated throughout inverse method. In inversion procedure, the Tikhonov regularization method is used to reduce the inversion error. To estimate the wheel excitation force, the vibration of knuckle is measured and transfer function between knuckle and wheel center is also measured. The wheel excitation force is estimated by using the measured knuckle vibration and the inversed transfer function. Finally interior noise due to wheel force is estimated by multiplying wheel excitation force in the vibro-acoustic transfer function. This vibro-acoustic transfer function is obtained throughout measurement. The proposed method is validated by using cleat excitation method. Finally, it is applied to the estimation of interior noise of the vehicle with different types of tires during driving test.