• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1210-1215
• /
• 2000

일반적인 형태의 동적 시스템에 가해지는 외란이 유색잡음이며, 외란의 형태가 시간에 따라 불규칙하게 변할 때와 감쇠계수와 강성계수가 시간에 따라 불규칙하게 변할 때의 그 확률 시스템의 특성과 제어기법에 대하여 연구하였다. 고려된 물리적인 모델은 불규칙한 대기교란을 받는 항공익으로써 이는 "시변계"가 되며 그 지배방정식이 확률론적 관점에서 F-P-K 접근법으로 유도되었으며, "유색잡음용 허-확률제어기"의 효과를 확률 영역 및 시간영역에서 고찰하였다. 또한 확률론적 플러터경계에 대해서도 고찰하였다.

• Steel and Composite Structures
• /
• 제38권1호
• /
• pp.87-102
• /
• 2021

To investigate the failure form, bending stiffness, and residual bearing capacity of monolithic composite beams with laminated slab throughout the fire process, fire tests of four monolithic composite beams with laminated slab were performed under constant load and temperature increase. Different factors such as post-pouring layer thickness, lap length of the prefabricated bottom slab, and stud spacing were considered in the fire test. The test results demonstrate that, under the same fire time and external load, the post-pouring layer thickness and stud spacing are important parameters that affect the fire resistance of monolithic composite beams with laminated slab. Similarly, the post-pouring layer thickness and stud spacing are the predominant factors affecting the bending stiffness of monolithic composite beams with laminated slab after fire exposure. The failure forms of monolithic composite beams with laminated slab after the fire are approximately the same as those at room temperature. In both cases, the beams underwent bending failure. However, after exposure to the high-temperature fire, cracks appeared earlier in the monolithic composite beams with laminated slab, and both the residual bearing capacity and bending stiffness were reduced by varying degrees. In this test, the bending bearing capacity and ductility of monolithic composite beams with laminated slab after fire exposure were reduced by 23.3% and 55.4%, respectively, compared with those tested at room temperature. Calculation methods for the residual bearing capacity and bending stiffness of monolithic composite beams with laminated slab in and after the fire are proposed, which demonstrated good accuracy.

• 제어로봇시스템학회논문지
• /
• 제12권3호
• /
• pp.277-283
• /
• 2006

A recently proposed method for stabilizing haptic interfaces and teleoperation systems was tested with a 'PHANToM' commercial haptic device. The 'Passivity Observer' (PO) and 'Passivity Control1er' (PC) stabilization method was applied to stabilize the system but also excited a high frequency mode in the device. To solve this problem, we propose a method to use a timevarying desired energy threshold instead of fixed zero energy threshold for the PO, and make the actual energy input follow the timevarying energy threshold. With the time-varying energy threshold, we make the PC control action smooth without sudden impulsive behavior by distributing the dissipation. The proposed new PO/PC approach is applied to PHANToM with high stiffness (K = 5000N/m), and stable and smooth contact is guaranteed. Resetting and active environment display problems also can be solved with the reference energy following idea.

• Ocean Systems Engineering
• /
• 제10권4호
• /
• pp.399-414
• /
• 2020

A floating bridge is an innovative solution for deep-water and long-distance crossing. This paper presents a curved floating bridge's dynamic behaviors under the wind, wave, and current loads. Since the present curved bridge need not have mooring lines, its deep-water application can be more straightforward than conventional straight floating bridges with mooring lines. We solve the coupled interaction among the bridge girders, pontoons, and columns in the time-domain and to consider various load combinations to evaluate each force's contribution to overall dynamic responses. Discrete pontoons are uniformly spaced, and the pontoon's hydrodynamic coefficients and excitation forces are computed in the frequency domain by using the potential-theory-based 3D diffraction/radiation program. In the successive time-domain simulation, the Cummins equation is used for solving the pontoon's dynamics, and the bridge girders and columns are modeled by the beam theory and finite element formulation. Then, all the components are fully coupled to solve the fully-coupled equation of motion. Subsequently, the wet natural frequencies for various bending modes are identified. Then, the time histories and spectra of the girder's dynamic responses are presented and systematically analyzed. The second-order difference-frequency wave force and slowly-varying wind force may significantly affect the girder's lateral responses through resonance if the bridge's lateral bending stiffness is not sufficient. On the other hand, the first-order wave-frequency forces play a crucial role in the vertical responses.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.202-207
• /
• 1993

A theoretical and experimental study is presented for the force holding control of a miniature robotic ringer which is driven by a pair of piezoelectric unimorph cells. In the theoretical analysis, one finger is modeled as a flexible cantilever with a tactile force sensor at the tip and the mate of the finger is a solid beam supposed with sufficient stiffness. Further, the force sensor is modeled by a one-degree-of-freedom, mass-spring system and the output of sensor is then described by the sensor stiffness multiplied by the relative displacement. The problem investigated in this paper is that two typical holding tasks of the human finger are picked up and applied to the robotic finger. One is the work holding a stationary object with a prescribed, time-varying force and the other one is to keep the contacted force constant even if the object is in motion. The simple PID feedback control scheme is used to control the minute gripping force of order 0.01 Newton. It is shown both experimentally and theoretically that the artificial finger with the piezoelectric actuator works well in the minute force holding of the tiny object.

• 한국지진공학회논문집
• /
• 제8권6호통권40호
• /
• pp.73-80
• /
• 2004

구조물의 손상 진단을 위해 측정 가속도 데이터를 사용한 비선형 시간영역 SI 알고리듬을 개발하였다. 구조물의 비선형 거동을 고려하기 위하여 측정 가속도 증분과 해석에 의한 가속도 증분의 차이로 출력오차를 정의하고, 구속 비선형 최적화 문제를 풀어 최적 구조변수를 구하였다. 개발된 알고리듬은 시간에 따라 변하는 강성도와 감쇠 변수를 추정하도록 하였다. 구조물의 비선형 거동에 의한 복원력은 추정된 시간에 따라 변하는 구조변수와 Newmark-$\beta$법으로 계산한 변위를 사용하여 복원하였으며, 복원 과정에서 비탄성 거동에 대한 어떤 모델도 사전에 설정하지 않았다. 개발한 알고리듬에서는 측정오차와 공간 및 상태에 대한 불완전 측정의 경우를 고려하였다. 개발한 알고리듬을 검증하기 위하여 3층 전단건물에 대한 수치 모의시험과 실내 모형실험을 통한 연구를 수행하였다.

• 한국지진공학회논문집
• /
• 제3권2호
• /
• pp.87-96
• /
• 1999

시간영역에서의 구조물의 해석은 직접적분법과 모드중첩법에 의하여 구해질 수 있다 그 중에서도 모드중첩법에 의한 해석방법은 몇가지 저차 진동모드를 사용하여 비교적 정확한 해를 구할 수 있기 때문에 동적해석에 널리 사용되고 있다, 그러나 비선형해석에서는 각 부재들의 상태에 따라 강성이 달라지므로 고유 진동모드를 정의할수 없거나 변화되는 강성에 따라 고유진동 모드를 지속적으로 다시 구하여야 하는 불편 있으므로 모드 중첩법을 이용한 비선형해석은 완전탄소성모델 등 극히 제한된 조건에서만 실행이 가능하였다 본논문에서는 강성행렬을 각 부재별로 분리시키고 비선형복원력과 초기선형복언력과 초기선형복원력의 차이를 하중항에 반영시킴으로써 모드중첩법을 이용하여 비선형 해석은완전탄소성모델 등 극히 제한된 조건에서만 실행이 가능하였다 본 논문에서는 강성행렬을 각 부재별로 분리시키고 비선형 복원력과 초기선형복원력의 차이를 하중항에 반영시킴으로써 모드중첩법을 이용하여 비선형해석이 가능한 방법을 제시하고자 한다. 특히 각 부재 강성을 각 부재의 상대변위의 함수로 나타냄으로써 연속적인 계산이 가능하게 하였다 본 논문에서 제시된 방법은 전단보모델에 적용하였으며 모드 개수를 변화시켜 지진하중에 의한 최대변위를 계산하여 이를 직접적분버에 의한 결과와 비교하였다.

• Earthquakes and Structures
• /
• 제14권4호
• /
• pp.305-312
• /
• 2018

Significant research efforts were undertaken to evaluate seismic performance of vertically irregular buildings on flat ground. However, there is scarcity of study on seismic performance of buildings on hill slopes. The present study attempts to investigate seismic behaviour of reinforced concrete irregular stepback building frames with different configurations on sloping ground. Based on extensive regression study of free vibration results of four hundred seventeen frames with varying ground slope, number of story and span number, a modification is proposed to the code based empirical fundamental time period estimation formula. The modification to the fundamental time period estimation formula is a simplified function of ground slope and a newly introduced equivalent height parameter to reflect the effect of stiffness and mass irregularity. The derived empirical formula is successfully validated with various combinations of slope and framing configurations of buildings. The correlation between the predicted and the actual time period obtained from the free vibration analysis results are in good agreement. The various statistical parameters e.g., the root mean square error, coefficient of determination, standard average error generally used for validation of such regression equations also ensure the prediction capability of the proposed empirical relation with reasonable accuracy.

• Wind and Structures
• /
• 제24권5호
• /
• pp.481-500
• /
• 2017

A novel three-degree-of-freedom (DOF) forced vibration system has been developed for identification of aeroelastic (self-excited) load parameters used in time-domain response analysis of wind-excited flexible structures. This system is capable of forcing sinusoidal motions on a section model of a structure that is used in wind tunnel aeroelastic studies along all three degrees of freedom - along-wind, cross-wind, and torsional - simultaneously or in any combination thereof. It utilizes three linear actuators to force vibrations at a consistent frequency but varying amplitudes between the three. This system was designed to identify all the parameters, namely, aeroelastic- damping and stiffness that appear in self-excited (motion-dependent) load formulation either in time-domain (rational functions) or frequency-domain (flutter derivatives). Relatively large displacements (at low frequencies) can be generated by the system, if required. Results from three experiments, airfoil, streamlined bridge deck and a bluff-shaped bridge deck, are presented to demonstrate the functionality and robustness of the system and its applicability to multiple cross-section types. The system will allow routine identification of aeroelastic parameters through wind tunnel tests that can be used to predict response of flexible structures in extreme and transient wind conditions.

• 대한기계학회논문집A
• /
• 제37권12호
• /
• pp.1547-1557
• /
• 2013

시간변화 이동자기력이 작용하는 레일의 변형을 티모센코 보 이론(Timoshenko beam theory)로 가정하였으며, 보의 진동특성에 영향을 미치는 탄성체기초의 감쇠효과 및 강성을 고려하였다. 푸리에 급수와 수치해석을 이용해 강제진동모델의 동적응답과 임계속도를 구하였다. 레일의 진동모델을 유한요소 해석 및 오일러 보 이론(Euler beam theory)과 비교 검증하였다. 강제진동모델을 이용하여 레일의 영구변형을 예측하였으며, 실험결과 레일표면의 영구변형 및 마모를 확인하였다. 보의 설계변수인 레일의 형상, 재료, 탄성체 기초의 감쇠효과 및 강성이 레일의 임계속도 및 레일의 처짐, 축 방향 응력, 전단 응력에 미치는 영향에 대한 매개변수적 연구를 진행하였으며, 보의 설계방향을 얻을 수 있었다.