• Journal of Biosystems Engineering
• /
• v.22 no.2
• /
• pp.117-126
• /
• 1997

A series of soil bin experiment was carried out on sandy loam to investigate if it is possible to predict implement draft by some analog tool. Chisel configuration resembling a cone penetrometer section was used as an analog tool. The angle of cone was 30 degree. Three types of tillage implement, or oriental janggi, moldboard plow and chisel plow were chosen for this study. Experimental tillage speed was 0.22, 0.33, 0.49 m/s ad tillage depth was 8, 12, 16cm. For the experimental tillage speed range, the increase of tillage speed did not affect the tillage draft for the three types of implement and analog tool, but as the tillage depth increased, tillage draft of the three types of implement and analog tool increased linearly. The linear relationship was found between the tillage draft of analog tool and that of three types of tillage implement for the experimental tillage depth and speed range with high value of $R^2$ Thus it was concluded from the above results that an analog tool can be used to predict the tillage draft of oriental janggi, moldboard plow and chisel plow. But more experiment for various soil types and theoretical verification are needed for more generallization.

• Journal of Biosystems Engineering
• /
• v.32 no.4
• /
• pp.223-229
• /
• 2007

This study was conducted to develop a 2 row type band furrow tiller for a walking cultivator. The tillage and weeding operations in the furrow of dry fields has been done manually or chemical herbicide has been applied. The application of herbicide induces soil pollution and manual operation requires heavy labor. This 2-row type implement was developed to substitute this manual operation and to minimize soil pollution. The developed implement was composed of power transmitting device, tilling device, frame and tail wheel. The max. plowing width and depth were 300mm and 180mm, respectively. The revolutions of the hexagonal shaft and the tillage shaft were $227{\sim}376rpm$ and $355{\sim}590rpm$, respectively. The adequate working speed was $0.50{\sim}0.83m/s$ and the field capacity was $0.17{\sim}0.28hr/10a$.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.521-528
• /
• 2002

Rotary and plow implements are mainly utilized for the tillage operation in Korea, and a implement control system for agricultural tractors was designed and fabricated to improve the working accuracy and efficiency. The control system was composed of three units: 1) sensors fur detection of angle of liftarm, draft force, engine rpm, tillage depth and so on, 2) a controller, and 3) hydraulic circuits, which included solenoid valves and so on, for operation of three point linkage and implements. The control system can control the speed(high and low speed) of implements by adjusting input flow rates of the hydraulic cylinder which was controled by two speed valve, which was composed of a solenoid valve and a orifice. Indoor experiments were conducted to evaluate response characteristics of the designed implement control system under experimental conditions of various engine nm, two kinds of input flow rates of the cylinder and some input frequency. The results of experiments showed the response characteristics sufficient to use as the implement control system fur agricultural tractors.

• Journal of Biosystems Engineering
• /
• v.36 no.2
• /
• pp.89-95
• /
• 2011

Tractor implements are mainly utilized for the tillage operation. The proposed hydraulic system control was implemented to experimental apparatus. An implement control system for tractor using proportional valve was fabricated to improve the working efficiency. Hydraulic circuit included the proportional solenoid valve and on/off solenoid valve and so on. This paper shows results of a specification and design of an implement control system for tractor using proportional valve for automation. It was conducted to evaluate response characteristics of the designed implement control system under experimental conditions of various input flow rates. The results of experiments showd that the response characteristics was sufficient to be used as the implement control system.

• Korean Journal of Agricultural Science
• /
• v.42 no.1
• /
• pp.53-61
• /
• 2015

Development of highly efficient and energy-saving tractors has been one of the issues in agricultural machinery. For design of such tractors, measurement and analysis of load on major power transmission parts of the tractors are the most important pre-requisite tasks. Objective of this study was to perform pre-processing procedures before effective analysis of load data of agricultural tractors (30, 75, and 82 kW) during major field operations such as plow tillage, rotary tillage, baling, bale wrapping, and to select the suitable pre-processing method for the analysis. A load measurement systems, equipped in the tractors, were consisted of strain-gauge, encoder, hydraulic pressure, and radar speed sensors to measure torque and rotational speed levels of transmission input shaft, PTO shaft, and driving axle shafts, pressure of the hydraulic inlet line, and travel speed, respectively. The entire sensor data were collected at a 200-Hz rate. Plow tillage, rotary tillage, baling, wrapping, and loader operations were selected as major field operations of agricultural tractors. Same or different farm works and driving levels were set differently for each of the load measuring experiment. Before load data analysis, pre-processing procedures such as outlier removal, low-pass filtering, and data division were performed. Data beyond the scope of the measuring range of the sensors and the operating range of the power transmission parts were removed. Considering engine and PTO rotational speeds, frequency components greater than 90, 60, and 60 Hz cut off frequencies were low-pass filtered for plow tillage, rotary tillage, and baler operations, respectively. Measured load data were divided into five parts: driving, working, implement up, implement down, and turning. Results of the study would provide useful information for load characteristics of tractors on major field operations.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.178-187
• /
• 2000

The tillage operation by rotary implements is widely done in Korea. In the case of rotary implements, the tillage depth control system is one of important implement control systems. A contact type-sensor for measurement of the ground height was designed and fabricated to evaluate the possibility of application of the sensor on the tillage depth control system. Indoor experiments were conducted to obtain static and dynamic detection characteristics of the sensor under various conditions; 1) several moisture contents for four soil samples, 2) two soil surfaces with a designed configuration, 3) four heights of the sensor from the soil surface, 4) five traveling speeds of the carrier on which the sensor was attached, and so on. The experimental results showed the detection characteristics of the sensor sufficient as the ground height sensor of the tillage depth control system.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06a
• /
• pp.203-208
• /
• 1996

• Journal of Drive and Control
• /
• v.17 no.4
• /
• pp.141-151
• /
• 2020

The aim of this study was to analyze the safety factor of range-shift gear pairs on multi-purpose agricultural implement machinery for an optimal design of a transmission system. Gear-strengths such as bending and contact stress and safety factors were analyzed under three load conditions: an equivalent engine torque at plow tillage, a rated engine torque, and the maximum engine torque. Root and contact safety factor were calculated to be 3.88, 5.14, 2.24, 2.11, 2.21, 0.99 and 0.78, 0.94, 0.65, 0.68, 0.84, 0.85, respectively, under equivalent engine torque condition at the plow tillage. The root and contact safety factor were calculated to be 1.91, 2.53, 1.10, 1.04, 1.07, 0.48 and 0.55, 0.66, 0.46, 0.48, 0.59, 0.59, respectively, under rated engine torque condition. The root and contact safety factor were calculated to be 1.60, 2.11, 0.92, 0.87, 0.90, 0.40 and 0.51, 0.61, 0.42, 0.44, 0.54, 0.54, respectively, under the maximum engine torque condition. The multi-purpose agricultural implement machinery could be conducted under plow tillage operation. However, gear specifications for tooth surface need modification because the gear surface would be broken at all driving conditions as safety factors are lower than 1.

• Korean Journal of Agricultural Science
• /
• v.47 no.4
• /
• pp.1123-1134
• /
• 2020

The goal of this study was to develop an accelerated life test for an implement working pump for an agricultural tractor. The field experiments were conducted to measure the load of an implement working pump during major agricultural operations such as plow tillage, rotary tillage, baler operations, and wrapping operations. The measurement system for an implement working pump load was constructed using a pressure sensor, the engine rotational speed, and the hitch pump displacement. The measured implement working pump load was calculated as an equivalent load for each agricultural operation using the Palmgren-Miner rule, which is a cumulative damage method. The equivalent load was calculated using the total load data and peak load data when the total data included the operation of an implement working. The annual usage time of the agricultural tractor was applied to develop two integrated equivalent loads. The acceleration factor was calculated to develop an accelerated life test and was calculated from the two integrated equivalent loads, the maximum pressure, and the flow rate conditions of the hitch pump. In Korea, the warranty life of a tractor is 2,736 hours, and the time required for the test to guarantee the operational life of tractors was calculated as 7,561 hours. The acceleration factors were calculated as 453.6 and 38.3, respectively, from the total load data and peak load data. The fatigue test time can be shortened by 16.7 and 197.4 hours according to the result of the acceleration factors.

• Journal of the Korean Society of Industry Convergence
• /
• v.12 no.2
• /
• pp.79-83
• /
• 2009

In this study, actual state of operation of rotary tillage was surveyed in the central part of Korea which includes 29 rural community around Asan city, Choongnam principal. 29 heads of the village and 44 farmers were surveyed at the field with a questionnaire on the operation of rotary tillage with farm tractors. Power requirement of rotary tillage operation was measured at the field of each farmers during rotary tilling operation in the central part of Korea. Summaries of this study are summarized as follows. 1) Operations of tillage and land preparation were found to be carried out with farm tractors by 98 percents which are results of the survey on 29 heads of the village and 44 farmers. 2) More than half of the farms had tractors with horsepower more than 38 kW which states that most tractors were supplied in middle and large size. 3) The case of applying secondary tillage after the first primary tillage were 79 percent among the most of operations of tillage and field preparation. Rotary tillage were carried out on the most of wet paddy fields and only 14 percent of dry fields were cultivated with rotary tillage. 4) 63.6 percent of farm tractors were surveyed to meet the recommended field capacity on tillage operation by the government which were ranged from 15.1 to 34.9 ha. And the field capacity of these farm tractors were greater than that of annual total area of operation field, 13.2ha (data from Information of agricultural machinery, National agricultural products quality service, Korea), which states the utilization of agricultural machinery was high in the area surveyed. 5) 46 percent of farmers changed the blade of rotary implement when they used it over the field capacity of rotary blade of 33 ha which is the area of field for rotary operation per a blade change. 55 percent of farmers changed the rotary blade more than once per two years. 6) The required power for rotary operation of each farm tractors were measured as 17.206 kW at untilled paddy field and 34.989 kW at untilled dry field on the average, respectively. The required power for rotary operation was measured as 28.248 kW on the average at the paddy field which had been plowed once and 28.015 at the paddy field that had rotary tillage operation. Untilled dry field showed the highest value of the required power for rotary operation.