• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.5
• /
• pp.25-33
• /
• 2011

This work proposes a skinny-type 10b 50MS/s 0.13um CMOS three-step pipeline ADC for CIS applications. Analog circuits for CIS applications commonly employ a high supply voltage to acquire a sufficiently acceptable dynamic range, while digital circuits use a low supply voltage to minimize power consumption. The proposed ADC converts analog signals in a wide-swing range to low voltage-based digital data using both of the two supply voltages. An op-amp sharing technique employed in residue amplifiers properly controls currents depending on the amplification mode of each pipeline stage, optimizes the performance of op-amps, and improves the power efficiency. In three FLASH ADCs, the number of input stages are reduced in half by the interpolation technique while each comparator consists of only a latch with low kick-back noise based on pull-down switches to separate the input nodes and output nodes. Reference circuits achieve a required settling time only with on-chip low-power drivers and digital correction logic has two kinds of level shifter depending on signal-voltage levels to be processed. The prototype ADC in a 0.13um CMOS to support 0.35um thick-gate-oxide transistors demonstrates the measured DNL and INL within 0.42LSB and 1.19LSB, respectively. The ADC shows a maximum SNDR of 55.4dB and a maximum SFDR of 68.7dB at 50MS/s, respectively. The ADC with an active die area of 0.53$mm^2$ consumes 15.6mW at 50MS/s with an analog voltage of 2.0V and two digital voltages of 2.8V ($=D_H$) and 1.2V ($=D_L$).

• Korean Journal of Environmental Agriculture
• /
• v.18 no.1
• /
• pp.77-82
• /
• 1999

Three floating islands have been constructed for water quality improvement for a polluted irrigation reservoir. Each floating island consists of 10 segments. Each segment hay an area of $16m^2$(4×4m) and is made of wood frames and floats(polystyrene foam). We planted three species of aquatic macrophytes(Typha angustifolia, Zizania latifolia, and Phragmites australis) in floating island on June, 1998. They grew very well without death. We would like to evaluate Phragmites australis is the most suitable aquatic macrophyte that could be planted in a floating island because it maintained the best balance of its root and shoot among them. During their grown period, net primary productivity of Typha angustifolia was $962gDM/m^2$, Zizania latifolia was $1,115gDM/m^2$, and Phragmites australis was $523gDM/m^2$. From these data, it would be estimated to 5.0Kg uptake of nitrogen by aquatic macrophytes and phosphorus 0.8Kg in 3 floating islands. The floating islands worked well as a habitat of fish and prawns. Many kinds of insect lived on the floating islands. The floating island has not only the function of water quality treatment but also several advantages: improvement of landscape and species diversity; low cost of maintenance; low technology; unnecessary of energy; less susceptible to variations in pollutant loading. It could be evaluated a good measure of water quality improvement for an irrigation reservoir. However, it should be intensively studied to develop more light, strong, durable and low-priced frames for efficient floating islands.

• Journal of Nutrition and Health
• /
• v.35 no.4
• /
• pp.489-497
• /
• 2002

This study was conducted to determine if Mehrabian's eating-related characteristics questionnaire could be effectively applied in predicting obesity and eating disorders among Korean college students by examining the correlations between eating-related characteristics and anthropometry, nutrient intakes, psychological aspects of depression, and personality dimensions. The data were collected from 151 female students in classes of nutrition or psychology in Kyungnam University. Measurements of height, weight and triceps skinfold thickness (TSf) were made by well-trained interviewers, and BMI was calculated. Daily nutrient intakes were obtained from the self-reported three-day dietary records for the kinds and the amounts of foods consumed by the student subjects. The students were also asked to complete three questionnaires : Mehrabian's eating-related characteristics questionnaire, Eysenck Personality Questionnaire, and the Berk Depression Inventory. The results of the study were as follows : 1) Reliability of factored homogeneous item dimensions (FHIDS) of the translated version of the eating-related characteristics questionnaire showed a similar profile compared with the original. Moreover, the loading values of Cronbach-$\alpha$ for some FHIDs, which were excluded in order to constitute primary-level factors (for example, 'predisposition to obesity' etc) with a high reliability, were much lower than Mehrabian's. Therefore the eating-related characteristics questionnaire could be effectively used for Korean students for predicting predisposition to obesity and eating disorders. 2) With regard to the relationship between anthropometric indices and eating-related characteristics, BMI measurements showed a high and a positive correlation with 'predisposition to obesity' and 'uncontrollable urges to eat', and a negative correlation with a 'predisposition to anorexia'. The heavier body weight and the more fat mass that the subjects had, the higher the probability that the subjects were overeating. 3) The intakes of some minerals (Fe, K, Na) and Vitamin C showed significantly negative correlations with a 'predisposition to obesity' and a 'predisposition to anorexia'. But the intakes of vitamin B$_2$, niacin, and retinol were positively correlated with'uncontrollable urges to eat'. 4) Among personality dimensions, neuroticism had a positive correlation with a 'predisposition to obesity', 'uncontrollable urges to eat', and 'predisposition to anorexia'. 5) Neuroticism was negatively correlated with intakes of calories, carbohydrates, K, Fe, Vitamin C, etc. On the contrary, all personality dimensions were positively correlated with intakes of retinol. In conclusion, the translated version of Mehrabian's eating-related characteristics questionnaire appears to be effective for nutritional or psychological assessments of any predisposition to eating disorders among Korean college students.

• Geophysics and Geophysical Exploration
• /
• v.8 no.1
• /
• pp.50-58
• /
• 2005

Recently, the imaging of geological structures beneath water-covered areas has been in great demand because of numerous tunnel and bridge construction projects on river or lake sites. An electrical resistivity survey can be effective in such a situation because it provides a subsurface image of faults or weak zones beneath the water layer. Even though conventional resistivity surveys in water-covered areas, in which electrodes are installed on the water bottom, do give high-resolution subsurface images, much time and effort is required to install electrodes. Therefore, an easier and more convenient method is sought to find the strike direction of the main zones of weakness, especially for reconnaissance surveys. In this paper, we investigate the applicability of the streamer resistivity survey method, which uses electrodes in a streamer cable towed by ship or boat, for delineating a fault zone. We do this through numerical experiments with models of water-covered areas. We demonstrate that the fault zone can be imaged, not only by installing electrodes on the water bottom, but also by using floating electrodes, when the depth of water is less than twice the electrode spacing. In addition, we compare the signal-to-noise ratio and resolving power of four kinds of electrode arrays that can be adapted to the streamer resistivity method. Following this numerical study, we carried out both conventional and streamer resistivity surveys for the planned tunnel construction site located at the Han River in Seoul, Korea. To obtain high-resolution resistivity images we used the conventional method, and installed electrodes on the water bottom along the planned route of the tunnel beneath the river. Applying a two-dimensional inversion scheme to the measured data, we found three distinctive low-resistivity anomalies, which we interpreted as associated with fault zones. To determine the strike direction of these three fault zones, we used the quick and convenient streamer resistivity.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.6
• /
• pp.603-616
• /
• 2023

In this study, machine learning-based clustering and classification of residential noise in apartment buildings was conducted using frequency and temporal characteristics. First, a residential noise source dataset was constructed . The residential noise source dataset was consisted of floor impact, airborne, plumbing and equipment noise, environmental, and construction noise. The clustering of residential noise was performed by K-Means clustering method. For frequency characteristics, L_eq and L_max values were derived for 1/1 and 1/3 octave band for each sound source. For temporal characteristics, Leq values were derived at every 6 ms through sound pressure level analysis for 5 s. The number of k in K-Means clustering method was determined through the silhouette coefficient and elbow method. The clustering of residential noise source by frequency characteristic resulted in three clusters for both L_eq and L_max analysis. Temporal characteristic clustered residential noise source into 9 clusters for L_eq and 11 clusters for L_max. Clustering by frequency characteristic clustered according to the proportion of low frequency band. Then, to utilize the clustering results, the residential noise source was classified using three kinds of machine learning. The results of the residential noise classification showed the highest accuracy and f1-score for data labeled with L_eq values in 1/3 octave bands, and the highest accuracy and f1-score for classifying residential noise sources with an Artificial Neural Network (ANN) model using both frequency and temporal features, with 93 % accuracy and 92 % f1-score.

• The Korean Journal of Archival Studies
• /
• no.17
• /
• pp.247-292
• /
• 2008

Investigations have been started to set the modern history and national spirit to rights after Commissions were established. Those Commissions are established and operated with time limit to finish its own missions. They creates three kinds of records as acquired materials which acquired or are donated for investigation; investigation records as investigation reports; and administrative records that created while supporting organization's operation. The Commissions use more past records to do special tasks asnation's slate clean and uncovering the truth than other agencies. In other words, the commissions take the most advantages of well-managed records, however, their record management environment and operation systems are relatively loose than other permanent machineries. It has three reasons that; first, there is no record management regulations and criteria for machineries that have time limit. This affected each commissions 'systems and 6 Truth Commissions' record management systems are built separately and on the different level; Second, members lack responsibility from frequent sending, reinstatement, change, and restructuring and that makes troubles to produce and manage records; Third, central archives pay less attention to machineries that operated limited period as the truth commissions. The Commissions rather need more systematic control because its records have historical value. To solve these problems, record management regulations have to be prepared first with features of organizations running limited time and commissions' records as acquired materials or investigation records. Furthermore, building up standard record management system for the Commissions, standardizing transfer data, imposing professional record personnel, and setting limits frequent personnel changes would finish practical problems. Besides, those records created to reveal the truth should use for education and research because Truth Commissions are established to set unfortunate history right and not to repeat it again. The records would serve as steppingstone for establishment of the Truth Record Center that does education, information work, publication, and research with the records. The record center would help using the records efficiently and improving knowledge for its people. And, the center should devote people to recognize importance of the records.

• Journal of Intelligence and Information Systems
• /
• v.22 no.1
• /
• pp.107-118
• /
• 2016

The advent of 5G mobile communications, which is expected in 2020, will provide many services such as Internet of Things (IoT) and vehicle-to-infra/vehicle/nomadic (V2X) communication. There are many requirements to realizing these services: reduced latency, high data rate and reliability, and real-time service. In particular, a high level of reliability and delay sensitivity with an increased data rate are very important for M2M, IoT, and Factory 4.0. Around the world, 5G standardization organizations have considered these services and grouped them to finally derive the technical requirements and service scenarios. The first scenario is broadcast services that use a high data rate for multiple cases of sporting events or emergencies. The second scenario is as support for e-Health, car reliability, etc.; the third scenario is related to VR games with delay sensitivity and real-time techniques. Recently, these groups have been forming agreements on the requirements for such scenarios and the target level. Various techniques are being studied to satisfy such requirements and are being discussed in the context of software-defined networking (SDN) as the next-generation network architecture. SDN is being used to standardize ONF and basically refers to a structure that separates signals for the control plane from the packets for the data plane. One of the best examples for low latency and high reliability is an intelligent traffic system (ITS) using V2X. Because a car passes a small cell of the 5G network very rapidly, the messages to be delivered in the event of an emergency have to be transported in a very short time. This is a typical example requiring high delay sensitivity. 5G has to support a high reliability and delay sensitivity requirements for V2X in the field of traffic control. For these reasons, V2X is a major application of critical delay. V2X (vehicle-to-infra/vehicle/nomadic) represents all types of communication methods applicable to road and vehicles. It refers to a connected or networked vehicle. V2X can be divided into three kinds of communications. First is the communication between a vehicle and infrastructure (vehicle-to-infrastructure; V2I). Second is the communication between a vehicle and another vehicle (vehicle-to-vehicle; V2V). Third is the communication between a vehicle and mobile equipment (vehicle-to-nomadic devices; V2N). This will be added in the future in various fields. Because the SDN structure is under consideration as the next-generation network architecture, the SDN architecture is significant. However, the centralized architecture of SDN can be considered as an unfavorable structure for delay-sensitive services because a centralized architecture is needed to communicate with many nodes and provide processing power. Therefore, in the case of emergency V2X communications, delay-related control functions require a tree supporting structure. For such a scenario, the architecture of the network processing the vehicle information is a major variable affecting delay. Because it is difficult to meet the desired level of delay sensitivity with a typical fully centralized SDN structure, research on the optimal size of an SDN for processing information is needed. This study examined the SDN architecture considering the V2X emergency delay requirements of a 5G network in the worst-case scenario and performed a system-level simulation on the speed of the car, radius, and cell tier to derive a range of cells for information transfer in SDN network. In the simulation, because 5G provides a sufficiently high data rate, the information for neighboring vehicle support to the car was assumed to be without errors. Furthermore, the 5G small cell was assumed to have a cell radius of 50-100 m, and the maximum speed of the vehicle was considered to be 30-200 km/h in order to examine the network architecture to minimize the delay.

• Journal of the Korean Society for Library and Information Science
• /
• v.24
• /
• pp.9-51
• /
• 1993

The purpose of this study is twofold: to investigate into general characteristics of the abstracting services in Korea and to discuss general directions of development of the abstracting services in the country. This study is designed to achieve the purpose by gathering and analysing data related to the abstracting journals published in the past ten years and by comparing the results with similar data gathered by the investigator in 1984. The major conclusions made in this study is summarised as follows. (1) Researchers and professionals working in limited numbers of subject fields are benefited by abstracting services of recent achievements in research and development in Korea. Those in most of the fields have essentially no abstracting services of such achievements. Even many researchers and professionals in the limited numbers of the fields that have some elementary abstracting services are not informed of research results in their fields because the abstracting journals are scattered in many narrow subjects and in many cases, the abstracting journals only cover publications in some specific forms and kinds. (2) Abstracting journals of general subjects, which are supposed to be of more or less help to the researchers in the subject fields that have no abstracting journals of their own, have rapidly increased in number in the past ten years. Most of such abstracting journals carry thesis and dissertation abstracts, and the rest those of research papers published in specific places, in specific forms, by specific institutes, and of reports of research projects sponsored by specific foundations. These abstracting journals are not of the kind that comprehensively provide general readers with current awareness of publications of research results in Korea. (3) Most of the abstracting journals existing in Korea are published by institutions of higher education and research institutes, and the rest by commercial publishers, industrial firms, libraries, information centers, government agencies, research foundations, learned societies, etc. Those which publish many titles are small in number and those publish one or two titles are large in number. The former is largely made up of institutions of higher education and research institutes. (4) Ten years ago, there was not a single publishing house that produced abstracting journals. Three commercial publishing houses now produce abstracting journals. As this change occurs, centers of excellence are founded and competitive elements are introduced in abstracting services. This change, in turn, is expected to improve quality of the other abstracting journals in Korea. (5) The abstracting journals published in Korea are classified by type into those of dissertations, research papers, journal articles, patent specifications in that descending order. The fact that Master's and doctoral dissertation abstracts are dominating in Korea is due to the irrational practice of publishing those abstracts at many institutions. (6) Most of the abstracting journals existing in Korea are published by national or government-supported research institutes in order to publicise their own research outputs. Their coverage of literature is normally narrow, and naturally their value to users is limited. (7) The abstracting journals published in Korea increased in number at the rate of $77.8-100\%$ every five years in the past twenty-five years. Most of the abstracting journals that ceased to be published during the period survived for two years. (8) Korean is the desirable language for the abstracting journals designed to be distributed within Korea. About half of the abstracting journals published in Korea is printed in Korean and the other half in foreign languages, and in Korean with foreign languages. All the abstracting journals in foreign languages are printed in English xcept one, which is printed in Japanese. (9) Some twenty percent of the abstracting journals in Korea is published monthly, bimonthly, and quarterly. Others are published annually, biannually, and irregularly. The latter may not function properly as a current-awareness tool due to long intervals between their issues. It is particularly undesirable that about half of the abstracting journals in Korea is published irregularly. Most of the abstracting journals published in Korea are distributed freely to individuals and institutions selected by the publishers. (10) The abstracting journals published by the use of computers increased drastically in the past ten years. The abstracting journals produced by the conventional type-setting method will probably disappear In Korea in another ten years to come. Automation of the production of abstracting journals does not simply mean technical, economic improvement of publishing processes but availability of machine-readable databases that can be used for other purposes, including the generation of other publications and the provision of machine literature searching capabilities. Necessary steps should be taken for this important development that is occurring in the abstracting services in Korea.

• Journal of the Korean Society of Groundwater Environment
• /
• v.5 no.4
• /
• pp.177-191
• /
• 1998

For various kinds of waters including surface water, shallow groundwater (＜70 m deep) and deep groundwater (500∼810 m deep) from the Pungki area, an integrated study based on hydrochemical, multivariate statistical, thermodynamic, environmental isotopic (tritium, oxygen-hydrogen, carbon and sulfur), and mass-balance approaches was attempted to elucidate the hydrogeochemical and hydrologic characteristics of the groundwater system in the gneiss area. Shallow groundwaters are typified as the 'Ca-HCO$_3$'type with higher concentrations of Ca, Mg, SO$_4$and NO$_3$, whereas deep groundwaters are the 'Na-HCO$_3$'type with elevated concentrations of Na, Ba, Li, H$_2$S, F and Cl and are supersaturated with respect to calcite. The waters in the area are largely classified into two groups: 1) surface waters and most of shallow groundwaters, and 2) deep groundwaters and one sample of shallow groundwater. Seasonal compositional variations are recognized for the former. Multivariate statistical analysis indicates that three factors may explain about 86% of the compositional variations observed in deep groundwaters. These are: 1) plagioclase dissolution and calcite precipitation, 2) sulfate reduction, and 3) acid hydrolysis of hydroxyl-bearing minerals(mainly mica). By combining with results of thermodynamic calculation, four appropriate models of water/ rock interaction, each showing the dissolution of plagioclase, kaolinite and micas and the precipitation of calcite, illite, laumontite, chlorite and smectite, are proposed by mass balance modelling in order to explain the water quality of deep groundwaters. Oxygen-hydrogen isotope data indicate that deep groundwaters were originated from a local meteoric water recharged from distant, topograpically high mountainous region and underwent larger degrees of water/rock interaction during the regional deep circulation, whereas the shallow groundwaters were recharged from nearby, topograpically low region. Tritium data show that the recharge time was the pre-thermonuclear age for deep groundwaters (＜0.2 TU) but the post-thermonuclear age for shallow groundwaters (5.66∼7.79 TU). The $\delta$$\^$34/S values of dissolved sulfate indicate that high amounts of dissolved H$_2$S (up to 3.9 mg/1), a characteristic of deep groundwaters in this area, might be derived from the reduction of sulfate. The $\delta$$\^$13/C values of dissolved carbonates are controlled by not only the dissolution of carbonate minerals by dissolved soil CO$_2$(for shallow groundwaters) but also the reprecipitation of calcite (for deep groundwaters). An integrated model of the origin, flow and chemical evolution for the groundwaters in this area is proposed in this study.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.4
• /
• pp.405-417
• /
• 2010

Previous studies have already shown that mouthguard is effective in protecting jaw bone, teeth and oral tissue against sports trauma. However, other than severe trauma, repetitive force, such as disorders like clenching, cause teeth or oral tissue damage. These kinds of disorders usually present pathologic attrition in the posterior teeth, resorption in alveolar bone, loss of teeth and destruction of occlusion. Wearing a mouthguard is believed to be effective in preventing these disorders. But its effect is not examined thoroughly enough. The purpose of this study is to identify whether mouthguard is effective in reducing strain caused by clenching. Mandibular first molars in the normal occlusal relationship without any history of dental treatment were chosen. Biaxial type strain gauge was placed on the buccal surface of the tooth. Having maximum occlusal force, measured by load cell, as a standard, clenching intensity were divided into three stages; moment of slightly tooth contact, medium bite force (50% of maximum bite force), maximum bite force. Strain occurring in dentition in each stage with and without mouthguard was measured. Changes in strain (on dentition) between each stage and difference in strain, between with or without mouthguard were recorded by PCD-300 analyzer and PCD-30 soft ware. The data was statistically analyzed by Wilcoxon signed rank test. The following results were drawn; Without mouthguard, strain given on dentition increased as the clenching force increased. With mouthguard, strain given on dentition also increased as the clenching force increased. With mouthguard, strain decreased, in all cases of clenching force stages. Data on the moment of slightly tooth contact stage, had no statistical significance. However, with mouthguard, 50-90% of decrease in strain could be obtained in maximum occlusal force, compared to the group without mouthguard. Mouthguard decreased the strain on the dentition, caused by clenching. Therefore, mouthguard seems to be effective in preventing damage on dentition, by acting against clenching, which occurs both consciously and unconsciously during sports activities.