• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.54-54
• /
• 2010

In this study, the correlation between temperature and the gel-content of the module were analyzed through experiments. Amorphous thin-film solar cell used in this experiment has a visible light transmission performance of 10%. In addition, ethylene vinyl acetate(EVA) film and the clear glass have been used for the modulation. The most important process is to laminate the module in the manufacturing process of BIPV(Building integrated photovoltaic) module. Setting parameters of laminator in the lamination process are temperature, pressure and time. Setting conditions significantly affect the durability, watertightness and airtightness of module. The most important factor in the setting parameters is temperature to satisfy the gel-contents. The bottom and top surface temperature of module are measured according to setting temperature of laminator. The results showed $145^{\circ}C$ of max temperature of the bottom surface and $128^{\circ}C$ of max temperature of top surface on the module at the temperature condition of $160^{\circ}C$. And at the another temperature condition of laminator with $150^{\circ}C$, the max temperature do bottom and top are $117^{\circ}C$ and $134^{\circ}C$ respectively. The temperature difference between bottom and top of the module occurred, that is because heat has been blocked by the clear glass and the bottom of the cells absorb the heat from the laminator. In this particular, the temperature difference between setting temperature of the laminator and the surface temperature of the module showed $15^{\circ}C$, because the heat of laminator plate is transferred to the surface of the module and heat is lost at this time. As a results, gel-content showed 94.8%, 88.7% and 81.7% respectively according to the setting temperature $155^{\circ}C$, $150^{\circ}C$ and $145^{\circ}C$ of the laminator. In conclusion, the surface temperature of module increases, the gel-contents is relatively increased. But if the laminator plate temperature is too high, the gel-content shows rather decline in performance. Furthermore, the temperature difference between setting temperature and the surface temperature of the module is affected by laminating machine itself and the temperature of module should be considered when setting the laminator.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1058-1062
• /
• 2000

We investigated resistive superconducting fault current limites (SFCLs) fabricated using YBCO thin films on 2-inch diameter sapphire substrates. Nearly identical SFCL units were prepared and tested. The units were connected in series and parallel to increase the current and voltage ratings. A serial connection of the units showed significantly unbalanced power dissipation between the units. This imbalance was removed by introducing a shunt resistor to the firstly quenched unit. Parallel connection of the units increased the current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current 25 A$\_$peak/, was produced and successfully tested at a 220 V$\_$rms/circuit. From the resistance increase, we estimated that the film temperature increased to 200 K in 5 msec, and 300 K in 120 msec. Successive quenches revealed that this system is stable without degradation in the current limiting capability under such thermal shocks as quenches at 220 V$\_$rms/.

• Current Photovoltaic Research
• /
• v.8 no.3
• /
• pp.102-106
• /
• 2020

In this paper, the effect of MoSe₂ on the contact resistance (R_C) of the transparent conducting oxide (TCO) and Mo junction in the scribed P2 region of the Cu(In,Ga)Se₂ (CIGS) solar module was analyzed. The CIGS/Mo junction becomes ohmic-contact by MoSe₂, so the formation of the MoSe₂ layer is essential. However, the CIGS solar module has a TCO/MoSe₂/Mo junction in the P2 region due to structural differences from the cell. The contact resistance (R_C) of the P2 region was calculated using the transmission line method, and MoSe₂ was confirmed to increase R_C of the TCO/Mo junction. B doped ZnO (BZO) was used as TCO, and when BZO/MoSe₂ junction was formed, conduction band offset (CBO) of 0.6 eV was generated due to the difference in their electron affinities. It is expected that this CBO acts as a carrier transport barrier that disturbs the flow of current, resulting in increased R_C. In order to reduce the R_C caused by CBO, MoSe₂ must be made thin in a CIGS solar module.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.342-345
• /
• 2002

As the size of chip components and module decreases, new patteming method for fine line and geometry is needed. So far, in LTCC(Low Temperature Cofired Ceramic) process, screen printing method has been used generally. But screen printing method has some disadvantages as follows. First, the geometry including line, vias, etc. smaller than $100{\mu}m$ can't be evaluated easily. Second, the patterned dimension is different from designed value, which makes distortion in charactersitics of not only chip components but also modules. Thick film lithography has advantages of thick film screen printing process, low cost and thin film process, fine line feasibility. Using this method, the line with $30{\mu}m$ width and the geometry with expected dimension can be evaluated. In this study, the fine line with $35{\mu}m$ line/space is formed and the embedded capacitor with very small tolerance is developed using thick film lithography.

• Journal of the Korean Vacuum Society
• /
• v.15 no.2
• /
• pp.180-185
• /
• 2006

Microwatt power level at relatively high voltage(order of volt) was produced by $Bi_{0.5}Sb_{1.5}Te_{3}/Bi_{2}Te_{2.4}Se_{0.6}$ thin film thermoelectric generators, and maximum output power varied with temperature difference in the square-law relation. Output voltage and current were possible to control by changing the way of electrical connection as well as the number of stacking plate-modules. Variation of open circuit voltage and short circuit current with temperature difference showed a linear relationship. There were, however, some differences in variations; open circuit voltage were dependent on the number of plate-module when connected in series, but it was not for parallel connection. On the other hand, short circuit current showed the opposite behavior to the case of open circuit current.

• KIEAE Journal
• /
• v.13 no.3
• /
• pp.91-96
• /
• 2013

The purpose of this study was to analyze the annual energy demand including heating, cooling and lighting according to kind of windows with transparent thin-film a-Si Building Integrated Photovoltaic(a-Si BIPV) for office building. The analysis results of the annual energy demand indicated that the a-si BIPV window was reduced by 8.4% than the clear gazing window. The base model A was combinate with a-Si BIPV window area of 67% and clear window area of 33% among the total exterior area. The model B is to be applied with low-e clear glass instead of clear glass of the base model A. The model B was reduced to annual energy demand of 1% more than the model A. Therefore, By using a-si BIPV solar module, the cooling energy demand can be reduced by 53%(3.4MWh) and the heating energy demand can be increase by 58%(2.4MWh) than clear glazing window in office building. Also, Model C applied to the high efficient lighting device to the model B was reduced to annual energy demand of 14.4% more than the Model D applied to the high efficient lighting device to the model A. The Model E applied with daylight dimming control system to the Model C was reduced to annual energy demand of 5.9% more than Model C.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.221-224
• /
• 2003

Recently, the market share of the thin-film-transistor liquid-crystalline-display (TFT-LCD) is growing rapidly in display device market. The backlight unit is used as a light source of TFT-LCD module. A light-guide is one of several important components of backlight unit. The manufacturing technology and optical system design of the light guide is very sensitive to quality and cost of the TFT-LCD module. In the present study a new manufacturing method which is called as direct surface forming(DSF) has been tested under various conditions. The result of this test, V-groove pattern shows different shapes depends on the temperature of mold surface, contact time of mold and depth of V-groove.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1053-1056
• /
• 2004

Chunghwa Picture Tubes, LTD. (CPT) has developed a Novel TFT-LCD Driving Techniquel. This new technique is developed in combination with other state-of-the-art image processing solutions such as image compression / decompression, motion detection, and noise reduction. By applying the Novel Driving Technique to the high resolution TFT-LCD, it was found that the response time can be effectively reduced with a lower overall system cost by smaller frame memory requirement, lower EMI by less memory band-width. Likewise, higher display quality can also be achieved in that the unexpected noises generated by over-drive can be eliminated. The Novel TFT-LCD Driving Technique has been successfully implemented to the 30 inch WXGA (1280${\times}$768) resolution TFT LCD commercial TV module. It was found that the quality of moving picture was better improved compared with that of the conventional fast response driving method.

• Korea-Australia Rheology Journal
• /
• v.15 no.4
• /
• pp.167-171
• /
• 2003

The backlight unit (BLU) is used as a light source of TFT liquid-crystalline-display (TFT-LCD) module. In this backlight unit, one of important components is the light guide, which is usually made of transparent polymers. Currently, the screen-printing method is mainly used for the light guide as a manufacturing process. However, it has limitation to the flexibility of three-dimensional optical design. In the present paper a new alternative manufacturing method for the light guide with low-cost is proposed. This manufacturing method is named as direct surface forming (DSF), which is very similar to the well-known hot embossing except for partial contact between mold and substrate. The results of this new manufacturing method are presented in terms of processing condition, dimensional accuracy, productivity, etc.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.406-409
• /
• 2003

In this paper, a 4-wavelength optical transceiver system is designed and implemented by using TFF (thin film filter) type OADMs (optical add-drop multiplexers). In this new system, the wavelengths of 1510 nm and 1530 nm are used for uploa and download signals, respectively, as well as the wavelengths of 1550 nm and 1310 nm which have been utilized in a 2-wavelength optical transceiver systems. The 4-wavelength optical module show pass characteristics of -1.6 dBm, -1.7 dBm, -5.6 dBm, -5.8dBm for 1510nm, 1530 nm, 1550 nm, 1570 nm, respectively, with 1.2 dBm of input laser power. The isolation for characteristics of the optical module for all the wavelengths are less than -40dB, which is very acceptable for filed requirements.