• 한국진공학회지
• /
• 제14권4호
• /
• pp.238-244
• /
• 2005

rf 마그네트론 스퍼터링 방법을 사용하여 유리기판 위에 $In_2O_3$ : ZnO=90 : 10 $wt.\%$의 조성비를 갖는 indium-zinc-oxide(IZO) 박막을 산소분압 $O_2$/(Ar +$O_2$) : $0\~10 \%$의 Ar가스 분위기에서 제작하였다. IZO 박막의 면저항은 증착 시 유입되는 산소량이 증가함에 따라 현저하게 증가하는데, 순수한 Ar 가스 분위기에서 증착될 때 $3.7\times10^{-4}\Omega\cdot$ cm 정도의 가장 낮은 비저항과 가시광 영역에서 평균 $85\%$ 이상의 투과율을 보이는 박막이 얻어진다. $600^{\circ}C$의 다양한 환경에서 옅처리될 경우, 순수한 Ar 분위기에서 성막된 IZO 박막의 전기적 저항 변화는 박막 내에 포함된 In 또는 InO와 같은 금속 성분들의 결정화와 산화에 의해 설명되어 진다. 또한 IZO 박막을 공기 중에서 열처리하는 동안 $600^{\circ}C$ 이상에서 현저하게 일어나는 산소 흡착과 구조 변화에 의한 전기적 특성들이 조사된다.

• 한국재료학회지
• /
• 제9권6호
• /
• pp.551-555
• /
• 1999

The deposition condition to obtain stoichiometric $Ta_2$O\ulcorner films, which is still controversial, using magnetron reactive sputtering was studied. The films were deposited by varying $O_2$gas flow rate with sputtering power and Ar gas flow rate of 200W and 60 sccm fixed. At the conditions of $O_2$ gas flow rate over 20 sccm, amorphous Tantalum oxide films with the refractive index of 2.1 and dielectric constant of 25 were deposited. Among those films, the capacitors dielectric properties of the film deposited at the condition of $O_2$ gas flow rate 50 sccm was best, the leakage current was 1$\times$10\ulcornerA/$\textrm{cm}^2$ at the electric field strength of 0.5 MC/cm and the breakdown field strength was over 2.0 MV/cm. This result could be explained from the analysis comparing with a standard sample using RBS because the composition of the film deposited at this condition was closest to the stoichiometric $Ta_2$O\ulcorner. The result of XPS analysis convinced that this film was stoichiometric $Ta_2$O\ulcorner film. A maximum cathode voltage was observed when $O_2$gas flow rate was 30 sccm. This shows that the Schiller's proposition that one can obtain stoichiometric films at the condition of maximum cathode voltage is not correct and more oxygen than that of the maximum voltage condition is necessary to deposit the stoichiometric Ta$_2$O\ulcorner films.

• 열처리공학회지
• /
• 제30권1호
• /
• pp.13-16
• /
• 2017

$SnO_2$ single layer films and 2 nm thick Ni thin film intermediated $AZO/Ni/SnO_2$ trilayer films were deposited on glass substrate at room temperatures by RF and DC magnetron sputtering and then the optical and electrical properties of the films were investigated to enhance opto-electrical performance of $SnO_2$ single layer films. As deposited $SnO_2$ films show the optical transmittance of 81.8% in the visible wavelength region and a resistivity of $1.2{\times}10^{-2}{\Omega}cm$, while $AZO/Ni/SnO_2$ films show a lower resistivity of $5.8{\times}10^{-3}{\Omega}cm$ and an optical transmittance of 77.1% in this study. Since $AZO/Ni/SnO_2$ films show the higher figure of merit than that of the $SnO_2$ single layer films, it is supposed that the $AZO/Ni/SnO_2$ films can assure high opto-electrical performance for use as a transparent conducting oxide in various display applications.

• 한국표면공학회지
• /
• 제40권4호
• /
• pp.190-196
• /
• 2007

Dye sensitized solar cells(DSSC) are the most promising future energy resource due to their high energy efficiency, low production cost, and simple manufacturing process. But one problem in DSSC is short life time compared to silicon solar cells. This problem occurred from photocatalytic degradation of dye material by nanometer sized $TiO_2$ particles. To prevent dye degradation as well as to increase its life time, the transparent coating film is needed for UV blocking. In this study, we synthesized nanometer sized $TiO_2$ particles in sols by increasing its internal pressure up to 200 bar in autoclave at $120^{\circ}C$ for 10 hrs. The synthesized $TiO_2$ sols were all formed with brookite phase and their particle size was several nm to 30 nm. Synthesized $TiO_2$ sols were coated on the backside of fluorine doped tin oxide(FTO) glass by ink jet printing method. With increasing coating thickness by repeated ink jet coating, the absorbance of UV region (under 400 nm) also increases reasonably. Decomposition test of titania powders dispersed in 0.1 mM amaranth solution covered with $TiO_2$ coating glass shows more stable dye properties under UV irradiation, compared to that with as-received FTO glass.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.255-255
• /
• 2010

Recently, nonvolatile memories (NVM) of various types have been researched to improve the electrical performance such as program/erase voltages, speed and retention times. Also, the charge trap memory is a strong candidate to realize the ultra dense 20-nm scale NVM. Furthermore, the high charge efficiency and the thermal stability of SiC nanocrystals NVM with single $SiO_2$ tunnel barrier have been reported. [1-2] In this study, the SiC charge trap NVM was fabricated and electrical properties were characterized. The 100-nm thick Poly-Si layer was deposited to confined source/drain region by using low-pressure chemical vapor deposition (LP-CVD). After etching and lithography process for fabricate the gate region, the $Si_3N_4/SiO_2/Si_3N_4$ (NON) and $SiO_2/Si_3N_4/SiO_2$ (ONO) barrier engineered tunnel layer were deposited by using LP-CVD. The equivalent oxide thickness of NON and ONO tunnel layer are 5.2 nm and 5.6 nm, respectively. By using ultra-high vacuum magnetron sputtering with base pressure 3x10-10 Torr, the 2-nm SiC and 20-nm $SiO_2$ were successively deposited on ONO and NON tunnel layers. Finally, after deposited 200-nm thick Al layer, the source, drain and gate areas were defined by using reactive-ion etching and photolithography. The lengths of squire gate are $2\;{\mu}m$, $5\;{\mu}m$ and $10\;{\mu}m$. The electrical properties of devices were measured by using a HP 4156A precision semiconductor parameter analyzer, E4980A LCR capacitor meter and an Agilent 81104A pulse pattern generator system. The electrical characteristics such as the memory effect, program/erase speeds, operation voltages, and retention time of SiC charge trap memory device with barrier engineered tunnel layer will be discussed.

• 한국정보통신학회논문지
• /
• 제11권4호
• /
• pp.760-765
• /
• 2007

본 연구에서는 나노구조 이중게이트 FinFET에 대하여 문턱전압이동 특성 및 드레인유기장벽저하(Drain Induced Barrier Lowering; DIBL)특성을 분석하였다. 분석을 위하여 분석학적 전류모델을 개발하였으며 열방사전류 및 터널링전류를 포함하였다. 열방사전류는 포아슨방정식에 의하여 구한 포텐셜분포 및 맥스월-볼쯔만통계를 이용한 캐리어분포를 이용하여 구하였으며 터널링 전류는 WKB(Wentzel-Kramers-Brillouin)근사를 이용하였다. 이 두 모델은 상호 독립적이므로 각각 전류를 구해 더함으로써 문턱 전압을 구하였다. 본 연구에서 제시한 모델을 이용하여 구한 문턱 전압 이동값이 이차원 시뮬레이션값과 비교되었으며 잘 일치함을 알 수 있었다. 분석 결과 10nm 이하에서 특히 터널링의 영향이 증가하여 문턱전압이동 및 DIBL이 매우 현저하게 나타남을 알 수 있었다. 이러한 단채널현상을 감소시키기 위하여 채널두께 및 게이트산화막의 두께를 가능한한 얇게 제작하여야함을 알았으며 이를 위한 산화공정개발이 중요하다고 사료된다.

• 한국표면공학회지
• /
• 제54권6호
• /
• pp.302-306
• /
• 2021

SnO₂ 30/Ag 15/SnO₂ 30 nm(SAS) tri-layer films were deposited on the glass substrates with RF and DC magnetron sputtering and then electron beam is irradiated on the surface to investigate the effect of electron bombardment on the opto-electrical performance of the films. electron beam irradiated tri-layer films at 1000 eV show a higher figure of merit of 2.72×10^-3 Ω^-1 than the as deposited films due to a high visible light transmittance of 72.1% and a low sheet resistance of 14.0 Ω/☐, respectively. From the observed results, it is concluded that the post-deposition electron irradiated SnO₂ 30/Ag 15/SnO₂ 30 nm tri-layer films can be used as a substitute for conventional transparent conducting oxide films in various opto-electrical applications.

• Current Photovoltaic Research
• /
• 제7권1호
• /
• pp.9-14
• /
• 2019

Carrier selective solar cell structure has allured curiosity of photovoltaic researchers due to the use of wide band gap transition metal oxide (TMO). Distinctive p/n-type character, broad range of work functions (2 to 7 eV) and risk free fabrication of TMO has evolved new concept of heterojunction intrinsic thin layer (HIT) solar cell employing carrier selective layers such as $MoO_x$, $WO_x$, $V_2O_5$ and $TiO_2$ replacing the doped a-Si layers on either front side or back side. The p/n-doped hydrogenated amorphous silicon (a-Si:H) layers are deposited by Plasma-Enhanced Chemical Vapor Deposition (PECVD), which includes the flammable and toxic boron/phosphorous gas precursors. Due to this, carrier selective TMO is gaining popularity as analternative risk-free material in place of conventional a-Si:H. In this work hole selective materials such as $MoO_x$, $WO_x$ and $V_2O_5$has been investigated. Recently $MoO_x$, $WO_x$ & $V_2O_5$ hetero-structures showed conversion efficiency of 22.5%, 12.6% & 15.7% respectively at temperature below $200^{\circ}C$. In this work a concise review on few important aspects of the hole selective material solar cell such as historical developments, device structure, fabrication, factors effecting cell performance and dependency on temperature has been reported.

• 한국재료학회지
• /
• 제29권1호
• /
• pp.1-6
• /
• 2019

Recent industrialization has led to a high demand for the use of fossil fuels. Therefore, the need for producing hydrogen and its utilization is essential for a sustainable society. For an eco-friendly future technology, photoelectrochemical water splitting using solar energy has proven promising amongst many other candidates. With this technique, semiconductors can be used as photocatalysts to generate electrons by light absorption, resulting in the reduction of hydrogen ions. The photocatalysts must be chemically stable, economically inexpensive and be able to utilize a wide range of light. From this perspective, cuprous oxide($Cu_2O$) is a promising p-type semiconductor because of its appropriate band gap. However, a major hindrance to the use of $Cu_2O$ is its instability at the potential in which hydrogen ion is reduced. In this study, gold is used as a bottom electrode during electrodeposition to obtain a preferential growth along the (111) plane of $Cu_2O$ while imperfections of the $Cu_2O$ thin films are removed. This study investigates the photoelectrochemical properties of $Cu_2O$. However, severe photo-induced corrosion impedes the use of $Cu_2O$ as a photoelectrode. Two candidates, $TiO_2$ and $SnO_2$, are selected for the passivation layer on $Cu_2O$ by by considering the Pourbaix-diagram. $TiO_2$ and $SnO_2$ passivation layers are deposited by atomic layer deposition(ALD) and a sputtering process, respectively. The investigation of the photoelectrochemical properties confirmed that $SnO_2$ is a good passivation layer for $Cu_2O$.

• 한국재료학회지
• /
• 제29권5호
• /
• pp.322-327
• /
• 2019

Hole carrier selective MoOx film is obtained by atomic layer deposition(ALD) using molybdenum hexacarbonyl[$Mo(CO)_6$] as precursor and ozone($O_3$) oxidant. The growth rate is about 0.036 nm/cycle at 200 g/Nm of ozone concentration and the thickness of interfacial oxide is about 2 nm. The measured band gap and work function of the MoOx film grown by ALD are 3.25 eV and 8 eV, respectively. X-ray photoelectron spectroscopy(XPS) result shows that the $Mo^{6+}$ state is dominant in the MoOx thin film. In the case of ALD-MoOx grown on Si wafer, the ozone concentration does not affect the passivation performance in the as-deposited state. But, the implied open-circuit voltage increases from $576^{\circ}C$ to $620^{\circ}C$ at 250 g/Nm after post-deposition annealing at $350^{\circ}C$ in a forming gas ambient. Instead of using a p-type amorphous silicon layer, high work function MoOx films as hole selective contact are applied for heterojunction silicon solar cells and the best efficiency yet recorded (21 %) is obtained.