• Membrane and Water Treatment
• /
• v.2 no.3
• /
• pp.137-145
• /
• 2011

Membrane processes are major breakthrough for the removal of organic pollutants in water remediation. The separations of solutes depend on nature of the membranes and solutes. The separation performance depends on the nature of the solutes (i.e., molecular volume, polarity, and hydrophobicity) for the same membrane. As 4-chlorophenol is of more dipolemoment compared to 2-chlorophenol, the orientation of the molecule enables it pass through the pores of the membrane, which is of negatively charged and thus separation order follows: 2-chlorophenol > 4-chlorophenol. Hydrophobicity factor also supports the order. Addition of sodium dodecyl sulfate (SDS) to chlorophenol solution shows remarkable increase in separation performance of the membrane. The improvement in separation is 1.8 and 1.5 times for 4- and 2- chlorophenol consecutively in case of 0.0082 M SDS (1cmc = 0.0082 M) in the solution. 4-chlorophenol has better attachment tendency with SDS because of its relatively more hydrophobic nature and thus reflects in performance i.e. the separation performance of 4-chlorophenol with SDS through the membrane is better compared to 2-chlorophenol.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.3
• /
• pp.327-334
• /
• 2016

The effects of dissolved inorganic and organic matter in seawater and the characteristics of fouling on the membrane surface were investigated within membrane distillation (MD) process. The changes of the membrane flux of PE and PVDF hollow fiber membranes under natural and synthetic seawater were compared with given variances of temperature. The flux of both membranes under the synthetic seawater, without any organic matter, were higher than that of the natural seawater, indicating the organic fouling on the membrane surface. The surface of the membrane was analyzed using scanning electron microscope (SEM) to examine the fouling. The experiment with organics has shown the formation of thin film over the membrane surface, while the experiment with inorganics has shown only the formation of inorganic crystals. The results indicated the organic matter as the major foulants and that the organics affected the formation of the crystals. Permeate water conductivity of all conditions verified the quality of the water to be better if not similar to that of RO.

• Applied Microscopy
• /
• v.1 no.1
• /
• pp.11-17
• /
• 1969

Conidio spores of Aspergillus niger (strain No. NRRL 330) cultured on potato dextrose agar media were studied by electron microscopy, using the thin sectioning techniques. Conidio spores to be sectioned were fixed by triple methods with $K_2Cr_2O_7$, Glutaraldehyde and $OsO_4$. After dehydrated with alcohol, the specimens were embedded in metacrylate and epon resin media, and thinly sectioned by Porter-Blum MT-2. After sectioned these specimens were negative-stained with uranyl acetate and observed. by Hitachi HS-6 electron microscope. The results of this experiment were summarized as follows. 1. The structures of spore ,wall system seem to be formed 4 layers; exosporium, basal layer, spore coat and unit cell membrane. The protuberance of spore surface that was looked like hair appears to be protrusived from the basal layer. 2. The 3 layers of unit cell membrane was constituted outer layer membrane, inner layer membrane and inter-mediate light layer. 3. The structures of intra cytoplasmic membrane appear as spiral form which was consisted of 3 layers membrane system; outer membrane, inner membrane, and intermediate layer, which has pits. 4. The cement substance of spore coat and cortex may be changed quantitatively by physiological state in cell. 5. In some cases, we observed that the ribosome was transformed into poly ribosome group, and the storage materials and the protein crystals were changed variously. It. has been suggested that the morphological change of some cytoplasmic materials may be caused by some specialized function of the physiological stage.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.38-45
• /
• 2020

Although Lithium metal battery (LMB) has a very large theoretical capacity, it has a critical problem such as formation of dendrite which causes short circuit and short cycle life of the LMB. In this study, PDMS/GO composite with evenly dispersed graphene oxide (GO) nanosheets in poly (dimethylsiloxane) (PDMS) was synthesized and coated into a thin film, resulting in the effect that can physically suppress the formation of dendrite. However, PDMS has low ion conductivity, so that we attained improved ion conductivity of PDMS/GO thin film by etching technic using 5wt% hydrofluoric acid (HF), to facilitate the movement of lithium (Li) ions by forming the channel of Li ions. The morphology of the PDMS/GO thin film was observed to confirm using SEM. When the PDMS/GO thin film was utilized to lithium metal battery system, the columbic efficiency was maintained at 87.4% on average until the 100^th cycles. In addition, voltage profiles indicated reduced overpotential in comparison to the electrode without thin film.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2482-2487
• /
• 2007

Numerical simulations are conducted for the analysis of a thermal mass air flow sensor with periodic heating pulses on silicon-nitride ($Si_3N_4$) thin membrane structure. This study aims to find the locations of temperature sensors on the thin membrane and the heating pulse conditions, that the higher sensitivity can be achieved, for the development of a MEMS fabricated mass air flow sensor which is driven in periodic heating pulse. The simulations, thus, focus on the membrane temperature profile according to variation of the flow velocity, heating duration time and imposed power. The flow velocity of the simulations is ranging from 3 m/s to 35 m/s, heating duration time from 1 ms to 3 ms and imposed power from 50 mW to 90 mW. The corresponding Reynolds numbers vary from 1000 to 10000.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.2
• /
• pp.127-137
• /
• 2020

In this study, a MWCNT(multi-wall carbon nanotube) was added to polysulfone(PSf) support layer to improve flux of TFC(thin film composite) RO(reverse osmosis) membrane. Two different kinds of MWCNT were used. Surfaces of some MWCNTs were modified hydrophilically through acid treatment, while those of other MWCNTs were modified through heat treatment to maintain their hydrophobicity. MWCNT/PSf support layer was prepared by adding PSf to the NMP mixed solvent containing 0.1 wt% MWCNTs using a phase inversion method. The surface porosity of the MWCNT/PSf support increased by 42~46% while its surface pore size being maintained. The TFC RO membrane made of MWCNT/PSf support layer showed a 20% flux increase while its salt rejection characteristics is sustained. In addition, the MWCNT/PSf support layer has better mechanical stability than the PSf support layer, there resulting in an increased resistance of flux reduction due to physical pressure.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.1
• /
• pp.6-11
• /
• 2016

For high volume manufacturing using extreme ultraviolet (EUV) lithography, mask protection from contamination during lithography process must be solved, and EUV pellicle is the strongest solution. Based on the technical requirements of EUV pellicle, EUV pellicle should have large membrane area ($110{\times}140mm^2$) with film transmittance over 90% and mechanical stability. Even though pellicle that satisfies size standard with high transmittance has been reported, its mechanical stability has not been confirmed, nor is there a standard to evaluate the mechanical stability. In this study, we suggest a rather simple method evaluating mechanical stability of pellicle membrane using spin-coater which can emulate the linear accelerated motion. The test conditions were designed by simulating the acceleration distribution inside pellicle membrane through correlating the linear acceleration and centripetal acceleration, which occurs during linear movement and rotation movement, respectively. By these simulation results, we confirmed the possibility of using spin-coater to evaluate the mechanical stability of EUV pellicle.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1971-1973
• /
• 2005

We fabricated an alumina membrane with nano-sized pore array by anodic oxidation using the thin film aluminum deposited on silicon wafer. It is important that the sample prepared by metal deposition method has a flat aluminum surface and a good adhesion between the silicon wafer and the thin film aluminum. The oxidation time was controlled by observation of current variation. The nano-sized pores with diameter of $60{\sim}120nm$ was obtained by $40{\sim}80$ voltage. The pore widening process was employed for obtaining the flat surface because the pores of the alumina membrane prepared by the fixed voltage method shows the structure of rough surface. Finally, the sample was immersed to the phosphoric acid with 0.1M concentration to etching the barrier layer. The sample will be applied to electronic sensors, field emission display, and template for nano- structure.

• Computers and Concrete
• /
• v.31 no.3
• /
• pp.223-239
• /
• 2023

Geometric nonlinear performance simulation and analysis of complex modern buildings and industrial products require high-performance shell elements. Balancing multiple aspects of performance in the one geometric nonlinear analysis element remains challenging. We present a new shell element, flat shell DKMGQ-CR (Co-rotational Discrete Kirchhoff-Mindlin Generalized Conforming Quadrilateral), for linear and geometric nonlinear analysis of both thick and thin shells. The DKMGQ-CR shell element was developed by combining the advantages of high-performance membrane and plate elements in a unified coordinate system and introducing the co-rotational formulation to adapt to large deformation analysis. The effectiveness of linear and geometric nonlinear analysis by DKMGQ-CR is verified through the tests of several classical numerical benchmarks. The computational results show that the proposed new element adapts to mesh distortion and effectively alleviates shear and membrane locking problems in linear and geometric nonlinear analysis. Furthermore, the DKMGQ-CR demonstrates high performance in analyzing thick and thin shells. The proposed element DKMGQ-CR is expected to provide an accurate, efficient, and convenient tool for the geometric nonlinear analysis of shells.

• Membrane Journal
• /
• v.27 no.5
• /
• pp.406-414
• /
• 2017

In this study, we have developed pore-filled ion-exchange membranes (PFIEMs) filled with ionomer in a thin polyethylene porous film (thickness = $25{\mu}m$) and investigated the charge-discharge characteristics of the all vanadium redox flow battery (VRFB) employing them. Especially, the degree of crosslinking and free volume of the PFIEMs were appropriately controlled to produce ion-exchange membranes exhibiting both the low membrane resistance and low vanadium permeability by mixing crosslinking agents having different molecular size. As a result, the prepared PFIEMs exhibited excellent electrochemical properties which are comparable to those of the commercial membranes. Also, it was confirmed through the experiments of vanadium ion permeability and VRFB performance evaluation that the PFIEMs showed low vanadium ion permeability and high charge-discharge efficiency in comparison with the commercial membrane despite their thin film thickness.