• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.287-290
• /
• 2005

CFRP strips manufactured in factory are produced normally with smaller width and larger thickness than CFRP sheets. By this reason, bonding force between CFRP strips and concrete substrate is not sufficient to sustain tensile force in CFRP strips. Therefore premature debonding failure cannot be avoided when strengthening is done by simply bonding the CFRP strips. The flexural strength of RC beam strengthened with CFRP strips must be calculated based on the effective strain considering debonding failure. This paper presents test results of an experimental study conducted to evaluate the flexural strength on RC beams strengthened with CFRP strips. 7 specimens were tested with respect to bond length and amount of CFRP strips. From the test results, it was indicated that the strain of the CFRP strips achieved at debonding failure can be decreased less than 6,000$\mu$ depending on the amount of CFRP strips.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.110-113
• /
• 2004

Aluminum and CFRP tube is light-weight material representatively but collapse mechanism is different under axial loading. Aluminum tube absorbs energy by stable plastic deformation under axialloading. While CFRP(Carbon Fiber Reinforced Plastics)tube absorb synergy by unstable brittle failure but its specific strength and stiffness is higher than that of aluminum tube. In this study, for complement of detect and synergy effect by combination with the advantages of each member, the axialcollapsetests were performed for combined aluminum CFRP tubes which are composed of aluminum tubes wrapped with CFRP out side aluminum square tubes. Collapsecharacteristics were analyzed for combined square tubes which have different CFRP orientation angle and thickness. Test results were compared with that of aluminum tubes and CFRP tubes.

• 한국안전학회지
• /
• 제29권6호
• /
• pp.9-14
• /
• 2014

Recently many efforts and researches have been done to cope with industrial facilities that require a low energy machines due to the gradual depletion of the natural resources. The fiber-reinforced composite materials in general have good properties and have the proper mechanical properties according to the change of the ply sequences and fiber distribution types. However, in the fiber-reinforced composite material, there are several problems, including fiber breaking, peeling, layer lamination, fiber cracking that can not be seen from the metallic material. Particularly, the fracture and delamination are likely to be affected by the thickness of the stacking laminates when the bi-material laminated structure is subjected to a load of the mixed mode. In this study, we investigated the effect of the thickness ratio of the difference in the CFRP/GFRP bi-material laminate composites by measuring the cracking behavior and the AE characteristics in a mixed mode loading, which may be generated in the actual structure. The results show that the thickness of the CFRP becomes more thick, the mode I energy release rate becomes a larger, and also the influence of mode I is greater than that of mode II. In addition, AE amplitude which shows the level of the damage in the structure was obtained the more damage in the CFRP with the thin thickness.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.295-300
• /
• 2002

To establish an optimum condition in the surface treatment and curing process will be an important parameters for the fabrication of multilayered hybrid composite materials, A17075/CFRP (CARALL : carbon fiber reinforce aluminum laminates). Effects of carbon fiber direction and thickness variation in tensile strength were investigated. And impact damage behavior of carbon fiber reinforce plastic (CFRP) and CARALL were investigated also, it was found that a partial stress increase in order of epoxy adhesive, A17075, CFRP. And the partial stress of CFRP carried out a great portion of applied stress. The impact damage resistance of CARALL was higher than that of CFRP. This is because both side Al sheet of CARALL absorb a great of impact damage.

• 한국생산제조학회지
• /
• 제21권3호
• /
• pp.421-424
• /
• 2012

Carbon Fiber reinforced composite material can be designed for the optimized performances of structural member that have achieve appropriate mechanical properties with cross-sectional shape, fiber direction, stacking sequence and thickness. So there are needed extensive databases each optimal design of CFRP structural member by impact through the preparation of different shape, interface number, thickness and stacking angle. When pressure is applied to structural member, compression, bending and torsion is shown on the corresponding member. For the effective utilization of fiber reinforced composite material as main structural member, optimized design technology should be established to maximize mechanical properties for compression, bending and torsion. In this paper, CFRP prepreg sheet with different stacking angle is manufactured in CFRP and hybrid(Al+CFRP) with circular cross-section. Strength and stiffness is gotten respectively by flexure test. CFRP structure and hybrid structure can be compared with each other. The best design guideline can be analyzed by use of this study result.

• 대한기계학회논문집A
• /
• 제24권8호
• /
• pp.2115-2122
• /
• 2000

The understanding of impact-induced delamination is important in safety and reliability of composite structure. In this study, a model for arrest toughness is proposed in consideration of fracture behavior of composite materials. Also, the probabilistic model is proposed to describe the variability of arrest toughness due to the nonhomogeneity of material. For these models, experiments were conducted on the Carbon/Epoxy composite plates with various thickness using the impact hammer. The elastic work factor used in J-Integral is applicable to the evaluation of energy release rate. The fracture behavior can be described by crack arrest concept and the arrest toughness is independent of the delamination size. Additionally, a probabilistic characteristics of arrest toughness is well described by the Weibull distribution function. A variation of arrest toughness increases with specimen thickness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.132-137
• /
• 2000

In this study, model for arrest toughness is proposed in consideration of fracture behavior of composite materials. Also, the probabilistic model is proposed to describe the variability of arrest toughness due to the nonhomogeneity of material. For these models. experiments were conducted on the Carbon/Epoxy composite plates with various thickness using the impact hammer. The elastic work fatter used in J-Integral is applicable to the evaluation of energy release rate. The fracture behavior call be described by crack arrest concept and the arrest toughness is independent of the delamination size. Additionally, a probabilistic characteristics of arrest toughness is well described by the Weibull distribution function. An increasing of thickness raises a variation of arrest toughness.

• Structural Engineering and Mechanics
• /
• 제13권1호
• /
• pp.75-90
• /
• 2002

Many existing concrete structures suffer from low quality of concrete and inadequate confinement reinforcement. These deficiencies cause low strength and ductility. Wrapping concrete by carbon fiber reinforced polymer (CFRP) composite sheets enhances compressive strength and deformability. In this study, the effects of the thickness of the CFRP composite wraps on the behavior of concrete are investigated experimentally. Both monotonic and repeated compressive loads are considered during the tests, which are carried out on strengthened undamaged specimens, as well as the specimens, which were tested and damaged priorly and strengthened after repairing. The experimental data shows that, external confinement of concrete by CFRP composite sheets improves both compressive strength and deformability of concrete significantly as a function of the thickness of the CFRP composite wraps around concrete. Empirical equations are also proposed for compressive strength and ultimate axial deformation of FRP composite wrapped concrete. Test results available in the literature, as well as the experimental results presented in this paper, are compared with the analytical results predicted by the proposed equations.

• Composites Research
• /
• 제26권4호
• /
• pp.207-212
• /
• 2013

본 연구에서는 유리강화섬유폴리머(GFRP)와 탄소강화섬유폴리머(CFRP)로 적층된 조류력 블레이드의 스파 캡(Spar cap)을 대상으로 끝단 처짐의 제한에 따른 단방향(UD) GFRP의 적층 두께를 최적화 하였다. 또한 도출된 적층 두께에 따른 블레이드 내부의 응력의 변화와 블레이드의 재료비용을 확인하였다. 비선형 최적화에 뛰어난 순차 이차방정식 프로그래밍(SQP) 알고리즘을 사용하였고, 목적함수를 계산하기 위하여 상용 유한요소해석 프로그램인 Abaqus/Standard와 연계하였다. UD CFRP의 적층 두께가 9 mm로 제한된 경우, 끝단 처짐이 감소함에 따라 UD GFRP의 적층 두께가 증가하였다. 즉, 최적화된 스파 캡의 무게는 최대 96.2% 증가였으며 최대 인장응력은 최대 24.6% 감소하였다. 끝단 처짐이 126.83 mm로 제한된 경우, UD CFRP의 적층 두께가 줄어듦에 따라 UD GFRP의 적층 두께가 증가하였다. 이로 인하여 무게는 최대 40.1% 증가하였지만 재료비용은 최대 16.97% 감소하였다. 본 연구에서 제시한 블레이드 스파 캡의 최적화된 두께를 바탕으로 조류력 블레이드의 무게, 내부의 최대 응력과 재료비용의 상관관계를 제시하였다.

• 복합신소재구조학회 논문집
• /
• 제2권2호
• /
• pp.13-19
• /
• 2011

본 연구에서는 강재가 맞대기 이음으로 연결될 경우 CFRP(Carbon Fiber Reinforced Plastic) 쉬트(sheet)를 맞대기 이음부에 접착할 경우 강재 및 CFRP 쉬트에 발생하는 응력을 해석하였다. CFRP 쉬트로 보강한 경우 접착제의 두께, 강재와의 접착 길이, CFRP 강도 변화를 매개변수로 사용하여 이 매개변수에 변화에 따른 이음부의 응력분포를 분석하였다. 또한 CFRP를 여러 층으로 접착할 경우 각 층의 강도를 다르게 변화시켜 맞대기 이음부에 유리한 응력분포를 나타내는 CFRP의 강도를 제시하였다. 본 연구를 위해 빠른 수렴성을 가지며 왜곡된 요소형상에서도 정확한 응력결과를 보이는 강화변형률장(Enhanced Assumed Strain Field)을 사용한 평면변형률 유한요소에 대한 프로그램을 작성하였다.