• KCI Concrete Journal
• /
• v.13 no.2
• /
• pp.10-18
• /
• 2001

The spectral analysis of surface waves (SASW) method, which is an in-situ seismic technique, has mainly been developed and used for many years to determine the stiffness profile of layered media (such as asphalt concrete and layered soils) in an infinite half-space. This paper presents a modified experimental technique for nondestructive evaluation of in-place cement mortar compressive strength in single-layer concrete slabs of rather a finite thickness through a correlation to surface wave velocity. This correlation can be used in the quality control of early age cement mortar structures and in evaluating the integrity of structural members where the infinite half space condition is not met. In the proposed SASW field test, the surface of the structural members is subjected to an impact, using a 12 mm steel ball, to generate surface wave energy at various frequencies. Two accelerometer receivers detect the energy transmitted through the medium. By digitizing the analog receiver outputs, and recording the signals for spectral analysis, surface wave velocities can be identified. Modifications to the SASW method includes the reduction of boundary reflections as adopted on the surface waves before the point where the reflected compression waves reach the receivers. In this study, the correlation between the surface wave velocity and the compressive strength of cement mortar is developed using one 36"x36"x4"(91.44$\times$91.44$\times$91.44 cm) cement mortar slab of 2,000 psi (140 kgf/$\textrm{cm}^2$) and two 36"x36"x4"(91.44$\times$91.44$\times$91.44 cm) cement mortar slabs of 3,000 psi (210 kgf/$\textrm{cm}^2$).

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.3
• /
• pp.391-397
• /
• 2015

Two hundred and sixteen Institut de S$\acute{e}$lection Animale (ISA) brown layers (40 wks of age) were studied for 6 wks to examine the effect of microalgae powder (MAP) on egg production, egg quality, blood lipid profile, and fatty acid concentration of egg yolk. Dietary treatments were as follows: i) CON (basal diet), ii) 0.5% MAP (CON+0.5% Schizochytrium powder), and iii) 1.0% MAP (CON+1.0% Schizochytrium powder). From 44 to 46 wks, egg production was higher in 1.0% MAP treatment than in control treatment (linear, p = 0.034); however, there was no difference on the egg production from 40 to 43 wks (p>0.05). Serum triglyceride and total cholesterol were significantly reduced in the groups fed with MAP, compared to those in groups fed with control diets (Quadratic, p = 0.034 and p = 0.039, respectively). Inclusion of 0.5% MAP in the diet of layers improved egg yolk color, compared with hens fed with basal diet at 46 wks (quadratic, p = 0.044). Eggshell thickness was linearly increased in MAP-fed treatments at 46th wk (p<0.05). Concentration of yolk docosahexaenoic acid (DHA; C22:6n-3) was increased in treatment groups fed with MAP (linear, p<0.05). The n-6 fatty acids, n-6/n-3 fatty acid, and unsaturated fatty acid/saturated fatty acid were decreased in treatment groups fed with MAP (linear, p<0.05). These results suggest that MAP improved the egg production and egg quality, and may affect serum lipid metabolites in the layers. In addition, MAP increases yolk DHA levels, and deceases n-6/n-3 fatty acid ratio.

• 한국생물공학회:학술대회논문집
• /
• 2003.04a
• /
• pp.74-78
• /
• 2003

Multi-channel images of 11-MUA and 11-MUOH self-assembled monolayers were obtained by using two-dimensional surface plasmon resonance (SPR) absorption. Patterning process was simplified by exploiting direct photo-oxidation of thiol bonding (photolysis) instead of conventional photolithography. Sharper images were resolved by using a white light source in combination with a narrow bandpass filter in the visible region, minimizing the diffraction patterns on the images. The line profile calibration of the image contrast caused by different resonance conditions at each points on the sensor surface (at a fixed incident angle) enables us to discriminate the monolayer thickness in sub-nanometer scale. Furthermore, there is no signal degradation such as photo bleaching or quenching which are common in the detection methods based on the fluorescence.

• Progress in Medical Physics
• /
• v.28 no.3
• /
• pp.106-110
• /
• 2017

The variable density phantom fabricated with varying the infill values of 3D printer to provide more accurate dose verification of radiation treatments. A total of 20 samples of rectangular shape were fabricated by using the $Finebot^{TM}$ (AnyWorks; Korea) Z420 model ($width{\times}length{\times}height=50mm{\times}50mm{\times}10mm$) varying the infill value from 5% to 100%. The samples were scanned with 1-mm thickness using a Philips Big Bore Brilliance CT Scanner (Philips Medical, Eindhoven, Netherlands). The average Hounsfield Unit (HU) measured by the region of interest (ROI) on the transversal CT images. The average HU and the infill values of the 3D printer measured through the 2D area profile measurement method exhibited a strong linear relationship (adjusted R-square=0.99563) in which the average HU changed from -926.8 to 36.7, while the infill values varied from 5% to 100%. This study showed the feasibility fabricating variable density phantoms using the 3D printer with FDM (Fused Deposition Modeling)-type and PLA (Poly Lactic Acid) materials.

• Korean Journal of Food Science and Technology
• /
• v.20 no.6
• /
• pp.742-748
• /
• 1988

The macro-and microstructure of Chinese cabbage used for Korean Kimchi preparation were examined and the texture characteristics of raw cabbage leaf and salted or blanched leaves were evaluated by cutting test. The length and thickness of leaf stalk increased with the order of pyllotaxis, but the thinning effect of outermost leaves was observed. The microstructure of cut-profile of stalk showed densely compacted vascular systems aligned in the center of stalk and the outer space was filled with large parenchima cells. Due to this structure, characteristic cutting curves were obtained by cutting test, composing three peaks of cutting for inner surface skin, center vascular system and outer surface skin. Salting and blanching increased the cutting force mainly due to the increase of Gutted cell wall number caused by the structure collapse.

• Tribology and Lubricants
• /
• v.32 no.2
• /
• pp.61-66
• /
• 2016

Total thickness variation (TTV), BOW, and surface roughness are essential characteristics for high quality sapphire substrates. Many researchers have attempted to increase removal rate by controlling the key process parameters like pressure and velocity owing to the high cost of consumables in sapphire chemical mechanical polishing (CMP). In case of the pressure approach, increased pressure owing to higher deviation of pressure over the wafer leads to significant degradation of the TTV. In this study, the authors focused on reducing TTV under the high-pressure conditions. When the production equipment polishes multiple wafers attached on a carrier, higher loads seem to be concentrated around the leading edge of the head; this occurs because of frictional force generated by the combination of table rotation and the height of the gimbal of the polishing head. We believe the skewed pressure distribution during polishing to be the main reason of within-wafer non-uniformity (WIWNU). The insertion of a hub ring between the polishing head and substrate carrier helped reduce the pressure deviation. Adjusting the location of the hub ring enables tuning of the pressure distribution. The results indicated that the position of the hub ring strongly affected the removal profile, which confirmed that the position of the hub ring changes the pressure distribution. Furthermore, we analyzed the deformation of the head via finite element method (FEM) to verify the pressure non-uniformity over the contact area Based on experiment and FEM results, we determined the optimal position of hub ring for achieving uniform polishing of the substrate.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.3
• /
• pp.265-277
• /
• 2001

This paper present a study on the flexural behavior of composite slabs using the flat-type profiled(ACE-DECK) steel deck plate which are developed recently. Forty eight composite slabs with different thickness, span, shear span and deck profile were tested to evaluate the flexural capacity and compared to the existing traperzodial deck profiles (KEM, ALPHA-DECK) According to the experiment results, flat-type profiled steel deck plate indicates more excellent capacity than existing traperzodial deck profiles in strength, stiffness, and ductility. The equation proposed by ASCE code for the effective moment of inertia are more acceptable than the equation proposed by ACI code. Thus, in this paper, test results are summarized by strength, stiffness, and deformation capacity for the specimens.

• Journal of Biosystems Engineering
• /
• v.31 no.6 s.119
• /
• pp.514-523
• /
• 2006

Production of green pepper has been increased due to customer's preference and a projected ten-year boom in the industry in Korea. This study was carried out to develop an automatic grading and sorting system for green pepper using machine vision. The system consisted of a feeding mechanism, segregation section, an image inspection chamber, image processing section, system control section, grading section, and discharging section. Green peppers were separated and transported using a bowl feeder with a vibrator and a belt conveyor, respectively. Images were taken using color CCD cameras and a color frame grabber. An on-line grading algorithm was developed using Visual C/C++. The green peppers could be graded into four classes by activating air nozzles located at the discharging section. Length and curvature of each green pepper were measured while removing a stem of it. The first derivative of thickness profile was used to remove a stem area of segmented image of the pepper. While pepper is moving at 0.45 m/s, the accuracy of grading sorting for large, medium and small pepper are 86.0%, 81.3% and 90.6% respectively. Sorting performance was 121 kg/hour, and about five times better than manual sorting. The developed system was also economically feasible to grade and sort green peppers showing the cost about 40% lower than that of manual operations.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1222-1228
• /
• 2002

This research is the development of a flexible tactile sensor array for service robots using PVDF (polyvinylidene fluoride) film for the detection of a contact state in real time. The prototype of the tactile sensor which has 8${\times}$8 array using PVDF film was fabricated. In the fabrication procedure, the electrode patterns and the common electrode of the thin conductive tape were attached to both sides of the 281$\mu\textrm{m}$ thickness PVDF film using conductive adhesive. The sensor was covered with polyester film for insulation and attached to the rubber base for a stable structure. The proposed fabrication method is simple and easy to make the sensor. The sensor has the advantages in the implementing for practical applications because its structure is flexible and the shape of the each tactile element can be designed arbitrarily. The signals of a contact force to the tactile sensor were sensed and processed in the DSP system in which the signals are digitized and filtered. Finally, the signals were integrated for taking the force profile. The processed signals of the output of the sensor were visualized in a personal computer, and the shape and force distribution of the contact object were obtained. The reasonable performance for the detection of the contact state was verified through the sensing examples.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.379-379
• /
• 2013

본 논문에서는 Normal ink jetting 공법으로 OTFT를 제작할 때 coffee stain effect에 의해서 반도체 소자의 특성이 저하되는 것을 극복하기 위해서 동일한 위치에 동일한 부피로 Droplet을 형성하는 Multiple ink jetting 공법을 통해 TIPS pentacene 결정의 Morphology와 전기적 특성이 어떻게 변화하는지 알아 보았다. Multiple ink jetting의 drop 횟수가 증가할수록 coffee stain effect에 의해서 형성된 가운데 영역의 Dendrite grain이 점점 작아지다가 7 Drops 이후로는 Big grain 만 남게 되었다. Active layer의 표면 Roughness는 drop 횟수가 증가할수록 낮아지다가 일정 count 이후로는 다시 높아지는 것을 확인할 수 있었다. 전계 이동도(mobility)는 drop 횟수가 증가할수록 커지다가 일정 count 이후로는 saturation되는 것을 확인할 수 있었다. Multiple ink jetting에 의해서 만들어진 OTFT 소자의 전계 이동도(mobility)는 1 drop과 10 drops에서 각각 0.0059, 0.036 cm2/Vs 로 6배 정도 차이가 있었다. 이것은 첫 drop에 의해 만들어진 가운데 Dendrite grain 영역이 Multiple ink jetting을 반복하면서 점점 작아지게 되어 사라지고 두꺼운 Grain 영역만 남게 된 것으로 판단된다. Vth 와 On/Off ratio는 1 drop과 10 drops에서 각각 -3 V, -2 V 그리고 $3.3{\times}10^3$, $1.0{\times}10^4$를 보였다. OTFT의 substrate로 Flexible한 polyethersulfone (PES) 기판을 사용하였고, 절연체로 Spin coating된 Poly-4-vinylphenol (PVP)가 사용되었으며, Gate 및 Source/Drain 전극은 Au를 50 nm 두께로 증착하였다. Channel의 width와 length는 각각 100 um, 40 um 였고, Gate 전극 위에 Active layer를 형성한 Bottom gate 구조로 제작되었다. Ink jet으로 제작된 TIPS pentacene의 결정성은 x-ray diffraction (XRD)와 광학 현미경으로 분석하였고 Thickness profile은 알파스텝 측정기를 이용하였으며, OTFT의 전기적 특성은 Keithley-4,200을 사용하여 측정하였다.