• Elastomers and Composites
• /
• v.54 no.3
• /
• pp.225-231
• /
• 2019

Bio-based polyester polyol was synthesized via esterification between azelaic acid and isosorbide. After esterification, bio-based polyurethanes were synthesized using polyester polyol, 1,3-propanediol as the chain extender, and 4,4'-diphenylmethane diisocyanate, in mixing ratios of 1:1:1.5, 1:1:1.8, 1:1:2, and 1:1:2.3. The bio TPU (Thermoplastic Polyurethane) samples were characterized by using FT-IR (Fourier Transform Infrared Spectroscopy), TGA (Thermal Gravimetric Analysis), DSC (Differential Scanning Calorimetry), and GPC (Gel Permeation Chromatography). The mechanical properties (tensile stress and hardness) were obtained by using UTM, a Shore A tester, and a Taber abrasion tester. The viscoelastic properties were tested by an Rubber Processing Analyzer in dynamic strain sweep and dynamic frequency test modes. The chemical resistance was tested with methanol by using the swelling test method. Based on these results, the bio TPU synthesized with the ratio of 1:1:2.3, referred to as TPU 4, showed the highest thermal decomposition temperature, the largest molecular weight, and most compact matrix structure due to the highest ratio of the hard segment in the molecular structure. It also presented the highest tensile strength, the largest elongation, and the best viscoelastic properties among the different bio TPUs synthesized herein.

• Macromolecular Research
• /
• v.15 no.2
• /
• pp.114-128
• /
• 2007

Polyimides are one of the most important classes of polymers used in the microelectronics and photoelectronics industries. Because of their high thermal stability, chemical resistance, and good mechanical and electric properties, polyimides are often applied in photoresists, passivation and dielectric films, soft print circuit boards, and alignment films within displays. Recently, fully aliphatic and alicyclic polyimides have found applications as optoelectronics and inter layer dielectric materials, due to their good transparencies and low dielectric constants $(\varepsilon)$. The low molecular density, polarity and rare probability of forming inter- or intra-molecular charge transfers, resulting in lowering of the dielectric constant and high transparency, are the most striking characteristics of aliphatic polyimide. However, the ultimate end use of polyimides derived from aliphatic monomers is in their targeted applications that need less stringent thermal requirements. Much research effort has been exerted in the development of aliphatic polyimide with increased thermal and mechanical stabilities, while maintaining their transparencies and low dielectric constants, by the incorporation of rigid moieties. In this article, the recent research process in synthesizing fully aliphatic polyimides, with improved dimensional stability, high transparency and low $\delta$values, as well as the characterizations and future scope for their application in micro electric and photo-electronic industries, is reviewed.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.333-341
• /
• 2000

Blends consisting of linear shape polylactic acid and star shape polylactic acid (L-PLLA/S-PLLA) have been prepared by melt and solution blending. The effect of blending method on the thermal properties and crystallization behavior of L-PLLA/S-PLLA blends has been investigated. The molecular weight decrease was revealed both in melt and solution blending. S-PLLA was found to be more stable than L-PLLA in the reduction of molecular weight during the course of blending due to its star shape structure. As a result, broad molecular weight distribution was obtained in solution blending. It was found that melting temperature and glass transition temperature decrease with increasing S-PLLA content. Blending method had large influence on the glass transition temperature of PLLA blends, while less effect on melting temperature. From DSC results, it can be noticed that solution blending is more effective blending method to obtain higher crystallinity than melt blending for S-PLLA and blend with higher S-PLLA content.

• Korean Journal of Materials Research
• /
• v.16 no.3
• /
• pp.183-187
• /
• 2006

We present the effects of rapid thermal annealing (RTA) temperature on the structural and optical properties of self-assembled InAs quantum dot (QD) structures grown on GaAs substrates by molecular beam epitaxy (MBE). The photoluminescence (PL) measurements are performed in a closed-cycle refrigerator as a function of temperature for the unannealed and annealed samples. RTA at higher temperature results in the increase in island size, the corresponding decrease in the density of islands, and the redshift in the PL emission from the islands. The temperature dependence of the PL peak energy for the InAs QDs is well expressed by the Varshni equation. The thermal quenching activation energies for the samples unannealed and annealed at $600^{\circ}C$ are found to be $25{\pm}5meV$ and $47{\pm}5$ meV, respectively.

• Interaction and multiscale mechanics
• /
• v.4 no.4
• /
• pp.247-255
• /
• 2011

Understanding the structural stability of carbon nanostructure under heat treatment is critical for tailoring the thermal properties of carbon-based material at small length scales. We investigate the heat resistance of the single carbon nanoball ($C_{60}$) and carbon nanoonions ($C_{20}@C_{80}$, $C_{20}@C_{80}@C_{180}$, $C_{20}@C_{80}@C_{180}C_{320}$) by performing molecular dynamics simulations. An empirical many-body potential function, Tersoff potential, for carbon is employed to calculate the interaction force among carbon atoms. Simulation results shows that carbon nanoonions are less resistive against heat treatment than single carbon nanoballs. Single carbon nanoballs such $C_{60}$ can resist heat treatment up to 5600 K, however, carbon nanoonions break down after 5100 K. This intriguing result offers insights into understanding the thermal-mechanical coupling phenomena of nanodevices and the complex process of fullerenes' formation.

• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.333-338
• /
• 2006

Silk fibroin (SF) fiber from the Antheraea pernyi silkworm was treated with a 1.23 N iodine-potassium iodide ($I_2-KI$) aqueous solution, and the structure and physical properties were investigated to clarify the effects of the iodine treatment. The noticeably high weight gain value of SF fiber, about 25 wt% was attributed to the absorption of polyiodide ions in the form of $I_3{^-}\;and\;I_5{^-}$. Fourier transform infrared spectroscopy and X-ray diffraction measurements suggested that polyiodide ions mainly entered the amorphous region. In addition, a new sharp reflection on the meridional direction, corresponding to a period of $7.0{\AA}$, was observed and indicated the possibility of the formation of mesophase structure of ${\beta}$-conformation chains. Dynamic viscoelastic measurements showed that the damping tan ${\delta}$ peak at $270^{\circ}C$ gradually shifted to lower temperature in the iodinated SF fibers, suggesting an enhancement of the molecular motion of the fibroin chains induced by the presence of polyiodide ions. With heating above $254^{\circ}C$, the iodine component introduced intermolecular cross-linking of SF, and the melt flow of the sample was inhibited. The thermal decomposition stability of fibroin molecules was greatly enhanced by iodine treatment.

• Fibers and Polymers
• /
• v.4 no.2
• /
• pp.59-65
• /
• 2003

PLA/LPCL/HPCL blends composed of poly(lactic acid) (PLA), low molecular weight poly($\varepsilon$-caprolactone) (LPCL), and high molecular weight poly($\varepsilon$-caprolactone) (HPCL) were prepared by melt blending for bioabsorbable fila-ment sutures. The effects of blend composition and blending time on the ester interchange reaction by alcoholysis in the PLA/LPCL/HPCL blends were studied. Their thermal properties and the miscibility due to the ester interchange reaction were investigated by $^1{H-NMR}$, DSC, X-ray, and UTM analyses. The hydroxyl group contents of LPCL in the blends decreafed by the ester interchange reaction due to alcoholysis. Thus, the copolymer was formed by the ester interchange reaction at $200^{\circ}C$ for 30-60 minutes. The thermal properties of PLA/LPCL/HPCL blends such as melting temperature and heat of fusion decreased with increasing ester interchange reaction levels. However, the miscibility among the three poly-mers was improved greatly by ester interchange reaction. Tensile strength and modulus of PLA/LPCL/HPCL blend fibers increased with increasing HPCL content, while the elongation at break of the blend fibers increased with increasing LPCL content.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.6
• /
• pp.1102-1108
• /
• 1997

Proteins and polysaccharides confer distinct functional properties in food systems. This research was attempted to improve emulsion properties of casein by protein-polysaccharide conjugation, in which alginates with various molecular weights were employed as polysaccharide sources. Casein-alginate mixtures were conjugated by the amino-carbonyl or Maillard reaction at 6$0^{\circ}C$ and 79% relative humidity. The resulting casein-alginate conjugates were tested for their emulsion activity and emulsion stabilizing properties. In general, the emulsion stability of casein-alginate mixture greatly increased due to the amino-carbonyl reaction between casein and alginates, whose magnitude depended on the molecular weight of alginate, weight ratio of casein to alginate and incubation time. It was also found that thermal stability and pH stability were markedly improved by the casein-alginate conjugation.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.5
• /
• pp.501-509
• /
• 1997

In recent papers[Bull. Kor. Chem. Soc. 1996, 17, 735; ibid 1997, 18, 478] we reported results of molecular dynamics (MD) simulations for the thermodynamic, structural, and dynamic properties of liquid normal alkanes, from n-butane to n-heptadecane, using three different models. Two of the three classes of models are collapsed atomic models while the third class is an atomistically detailed model. In the present paper we present results of MD simulations for the corresponding properties of liquid branched-chain alkanes using the same models. The thermodynamic property reflects that the intermolecular interactions become weaker as the shape of the molecule tends to approach that of a sphere and the surface area decreases with branching. Not like observed in the straight-chain alkanes, the structural properties of model Ⅲ from the site-site radial distribution function, the distribution functions of the average end-to-end distance and the root-mean-squared radii of gyration are not much different from those of models Ⅰ and Ⅱ. The branching effect on the self diffusion of liquid alkanes is well predicted from our MD simulation results but not on the viscosity and thermal conductivity.

• Macromolecular Research
• /
• v.15 no.3
• /
• pp.225-233
• /
• 2007

To improve the poor mechanical and low-temperature properties of glycidyl azide polymer (GAP)-based propellants, the addition of binders was investigated using GAP and flexible polymer backbone-structural polycaprolactone (PCP) at various weight(wt) ratios, and varying the ratio of Desmodur N-100 pluriisocyanate (N-100) to isophorone diisocyanate (IPDI). Using Gee's theory, the solubility parameter of the PCP network was determined, in order to elucidate the physical and chemical interaction between GAP and PCP. The structure of the binder networks was characterized by measuring the cross-link densities and molecular weights between cross-links ($M_c$) obtained by a swelling experiment using Flory-Rhener theory. The thermal and mechanical properties of the segmented block copolyurethane (GAP-b-PCP) binders prepared by the incorporation of PCP into the binder recipes were investigated, along with the effect of the different curatives ratios.