• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1131-1134
• /
• 2000

Hydroxyapatite (HA) ceramic was prepared using tuna bone powders and was characterized on properties of sintered samples. The aim was to prepare dense and bulk HA sintered suitable for clinical applications. Thermal analysis, X-ray diffraction analysis, microscopic observation, and mechanical evaluation were applied to characterize sintered HA to find optimum processing condition. The major phase of sintered HA was observed up to 1300$\^{C}$ and $\beta$-TCP was observed as temperature increased. The density of sintered HA was increased up to 1350$\^{C}$ and decreased with further increasing temperature. The flexural strength of sintered HA at 1350$\^{C}$ showed 58 MPa as the highest value in this work. The results suggest that the crystal phase and transformation characteristics of HA prepared from tuna bone are the same as the behavior of HA powders made by chemical synthesis.

• Macromolecular Research
• /
• v.13 no.1
• /
• pp.30-38
• /
• 2005

Sulfur-cured gum natural rubber vulcanizates were devulcanized using two different concentrations of diallyl disulfide. The devulcanization process was performed at $110^{\circ}C$ min in an open two-roll cracker-cum-mixing mill. Natural rubber vulcanizates having various sulfur/accelerator ratios were used to study the cleavage of monosulfide, disulfide, and polysulfide bonds. The properties of devulcanized natural rubber increased upon increasing the disulfide concentration and the mechanical properties of the revulcanized natural rubber increased upon decreasing the sulfur content in the original rubber vulcanizates. The scorch time and the maximum state of cure both increased when the ground vulcanizates were treated with higher amounts of disulfide. TGA and DMA were conducted to study the effects of the devulcanization on the thermal stability and the $T_g$ behavior of the vulcanizates. SEM analysis was conducted to study how the failure mechanism was affected by the devulcanization process. It was possible to recover $70-80\%$ of the original gum rubber properties by using this process. From IR spectroscopic analysis, we observed that the oxidation of the main chains did not occur during high-temperature milling.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.4
• /
• pp.111-120
• /
• 2008

The combustion reaction of polypropylene was investigated using a thermogravimetric technique under an air atmosphere condition at several heating rates from 10 to $50^{\circ}C/min$. To obtain information on the kinetic parameters, the dynamic thermogravimetric analysis curve and its derivative were analyzed by a variety of analytical methods such as Kissinger, Friedman, Freeman-Carroll, Chatterjee-Conrad, Ozawa and Coats-Redfern methods. The comparative works for the kinetic results obtained from various methods should be performed to determine the kinetic parameters, because there are tremendous differences in the calculated kinetic parameters depending upon the mathematical method taken in the analysis.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.4 s.37
• /
• pp.36-42
• /
• 2006

In the present work, characteristics of the flow in the cage of a steam turbine bypass control valve for thermal power plant are investigated. Experimental measurement for wall static pressure has been carried out to validate numerical solutions. And, the flowfield is analyzed by solving steady three-dimensional Reynolds-averaged Navier-Stokes equations. Shear stress transport (SST) model is used as turbulence closure. The effects of the flow area between stages of the cage on the pressure drop are also found.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.279-282
• /
• 2005

Recently, due to the launching of digital broadcasting service, a demand of PDP TV with large screen size is sharply rising. PDP power module is mainly divided into power factor correction (PFC) stage and sustaining power stage. Especially, sustaining power module has pulsating load characteristics. So, the hard switching at light load condition causes low efficiency and thermal problem. Therefore, a new power conversion circuit for sustaining power module of 60' PDP is proposed whose ZVS is obtained by additional ZVS tank. This paper presents properties of the proposed converter through mode analysis, numerical analysis. And a 900w prototype for sustaining power module of 60' PDP is produced to verify the analytic results. As an experimental results, ZVS is achieved from full load to 10% load variation and more than 92% of high efficiency is obtained at 10% load condition.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.424-426
• /
• 1999

In this paper, the design characteristics, the manufacturing process and the results of performance test on the AC traction motor for urban transit standard E.M.U which is newly developed with applying standardization specification will be introduced. It is reviewed that the design and performance analysis on conventional motors considering system correlation and design constraint and the design optimization through an analysis of electro-magnetic, thermal and dynamic properties. The properties of factory products manufactured by 200 Class VPI process exhibit a excellent performance with a lower noise and vibration, higher efficiency and power factor etc.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.88-93
• /
• 2005

Frictional heat generates when the brake shoes are in contact with wheel tread under high pressure for EMU's speed control, stopping, and deceleration. Such a frictional heat has a significant effect on the wheel tread. In order to analyze the characteristics of frictional heat and measure the amount of the generated heat, tests by using a brake dynamometer and for running vehicles are carried out. In addition, finite element analysis is performed to simulate the temperature distribution and thermal analysis of the brake shoes. Through the tests and the simulations, it is found that the problems by temperature increase at tread braking are verified.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.12
• /
• pp.1282-1287
• /
• 2001

This study presents the numerical analysis of natural convection of a micro- environments with air permeability in the clothing air-layer. As a numerical model the clothing air layer of shoulder and arm were adopted. Finite volume method for two-dimensional laminar flow was used for the analysis of flow and thermal characteristics of velocity, temperature and concentration in the air layer between body and clothing. As temperature boundary conditions, a body skin has a high temperature with $34^{\circ}C$ and the environmental temperatures are 5, 15 and $25^{\circ}C$ for various permeability coefficients. The distributions of concentration, temperature and velocity are shown that two large cells form at horizontal and vertical air layer, respectively. As the temperature difference between body skin and environment decreases, the heat transfer is decreased rapidly.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.1
• /
• pp.46-52
• /
• 2000

A computational analysis has been made on fluid flow in a regenerative cooling Passage for a reduced size liquid rocket engine to predict pressure drop and heat transfer rate in it. The contraction/expansion of the cross sectional area of the passage turn out to increases both the pressure loss and the heat transfer rate of the duct. The changes of the cross sectional area near the nozzle throat are effective to protect the throat which suffers from severe thermal load. Also given is the qualitative characteristics of the performance of the regenerative cooling system due to the variation of coolant flow rate.

• Journal of the Korean Society of Safety
• /
• v.23 no.6
• /
• pp.1-6
• /
• 2008

Machine operator and quality are affected by chip during cutting process to product machine parts. This paper presents a study of the influence of cutting conditions on the surface roughness obtained by turning using Taguchi method for safety of turning operator. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of its low thermal conductivity and chemical reactivity. Therefore titanium alloys are known as difficult-to materials. An orthogonal array, the signal-to-noise ratio, the analysis of variance are employed to investigate the cutting characteristics of implant material bars using tungsten carbide cutting tools of throwaway type. Also Experimental results by orthogonal array are compared with optimal condition to evaluate advanced reliability. Required simulations and experiments are performed, and the results are investigated.