• 한국세라믹학회지
• /
• 제55권6호
• /
• pp.608-617
• /
• 2018

The effects of the purity and monoclinic phase of feedstock powder on the thermal durability of thermal barrier coatings (TBC) were investigated through cyclic thermal exposure. Bond and top coats were deposited by high velocity oxygen fuel method using Ni-Co based feedstock powder and air plasma spray method using three kinds of yttria-stabilized zirconia with different purity and monoclinic phase content, respectively. Furnace cyclic thermal fatigue test was performed to investigate the thermal fatigue behavior and thermal durability of TBCs. TBCs with high purity powder showed better sintering resistance and less thickness in the thermally grown oxide layer. The thermal durability was found to strongly depend on the content of monoclinic phase and the porosity in the top coat; the best thermal fatigue behavior and thermal durability were in the TBC prepared with high purity powder without monoclinic phase.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1131-1137
• /
• 2004

With the recent continuous expansion of subways, newly created subways tend to have lower locations and wider sections. Furthermore. since box structures and evacuating tunnels are classified into a category of mass-concrete. the thermal-stress, emitted from the inside. causes cracks to structures from the inception of constructing. In this paper, thermal-stress analysis and durability evaluation of box structure were carried out to investigate relationship between durability and parameter causing the heat of hydration. Through the examination, this paper tries to find out satisfactory solutions to regulated thermal crack and ensure the required duration period. The results of this paper showed that to control thermal crack and guarantee the required duration period it was more effective to use low-heat-portland cement and moderateheat-portland cement. As cement volume due to reduction of water-cement ratio increased, the possibility of thermal cracks occurrence increased but results of durability evaluation was different depending on evaluation method. The results showed that the appropriate water-cement ratio to control the heat of hydration and satisfy the required durability was $45\∼55\%$. And it was showed that during placement of concrete blocks ambient temperature affect the heat of hydration. thermal crack and long-term durability largely and when concrete was placed at low temperature to control thermal crack. it need to try to guarantee the required duration period. Henceforth, by studying not only internal and external conditions, such as the relative humidity and the unit weight. but also methods, to evaluate durability, in accordance with domestic situations, more reasonable design of durability should be achieved.

• 한국추진공학회지
• /
• 제17권1호
• /
• pp.103-115
• /
• 2013

액체로켓 연소기에 사용되는 열차폐코팅(TBC)의 내구성 시험 기술동향을 조사하였다. 표면 접합력 측정을 위한 기계적 시험, 레이저나 가열로, 버너나 플라즈마 등을 이용한 열피로 시험, 분사기를 이용한 소형 연소시험, 열적 기계적 피로시험 등의 많은 내구성 시험들이 있었다. 연소기에 사용하기 위해 이러한 시편 수준의 시험을 통해 내구성이 확보된 TBC를 결정할 수 있으며, 실제 연소시험을 통해 내구성을 검증할 수 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.603-615
• /
• 2012

액체로켓 연소기에 사용되는 열차폐코팅(TBC)의 내구성 시험 기술동향을 조사하였다. 표면 접합력 측정을 위한 기계적 시험, 레이저나 가열로, 버너나 플라즈마 등을 이용한 열피로 시험, 분사기를 이용한 소형 연소시험, 열적 기계적 피로시험 등의 많은 내구성 시험들이 있었다. 연소기에 사용하기 위해 이러한 시편 수준의 시험을 통해 내구성이 확보된 TBC를 결정할 수 있으며, 실제 연소시험을 통해 내구성을 검증할 수 있다.

• 한국생산제조학회지
• /
• 제22권5호
• /
• pp.789-794
• /
• 2013

In this study, the temperature, heat emission per unit time, and thermal stress or deformation of a radiator fan made of polyethylene or aluminum are analyzed for investigating its strength durability. Heat transfer in the case of the aluminum radiator fan is better than that in the case of the polyethylene radiator fan. Further, heat emission in the case of the aluminum fan is poorer than that in the case of the polyethylene fan. Moreover, because the thermal deformation of aluminum is much smaller than that of polyethylene, the thermal durability of the aluminum fan is better than that of the polyethylene fan. In an open space in front of the radiator and the closed space of the engine behind it, the thermal cooling effect of the polyethylene fan is better than that of the aluminum fan. Further, since polyethylene is lighter in weight than aluminum, polyethylene, as a nonmetallic plastic, is more suitable as a material of an automotive radiator. However, because of the higher strength durability of the aluminum fan, it is better than the polyethylene fan under high-temperature conditions or in the case of a complex pipe.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.44-49
• /
• 2014

As expansion and contraction of bike disk brake are happened continuously by temperature at repeated urgent braking. In this study, 3 kinds of model are designed according to configurations of holes and thermal durabilities on bike disk brake are investigated by comparing 3 models through temperature and thermal analyses. Maximum thermal stress happened at the disk contacted with pad and the connection part fixing disk rotor. Instead of initial state, the temperature is uniformly distributed at transient state. As the area of hole at disk rotor face becomes wider, thermal stress becomes lower at the initial state. On the other hand, in case the number of holes increases, thermal stress becomes lower at the elapsed time of 100 seconds. The thermal durability of bike disk brake can be improved by applying this study result with configurations of holes.

• 한국정밀공학회지
• /
• 제27권9호
• /
• pp.58-66
• /
• 2010

This study examines thermal safety on three-way catalyst that dominates 70 % among whole exhaust gas purification device in 2003. Three-way catalyst durability in the Korea requires 5 years/80,000 km in 1988 but require 10 years/120,000 km after 2002. Three-way catalyst durability in the USA requires 7 years/120,000 km but require 10 years/160,000 km after 2004. Three-way catalyst maintains high temperature in interior domain but maintains low temperature on outside surface. Therefore this device shows tensile stress on outside surface. Temperature distribution of three-way catalyst was acquired by thermal flow analysis for predicted thermal flow parameter. Thermal stress analysis for three-way catalysis was performed based on this temperature distribution. Thermal safety of three-way catalyst was estimated by power law dynamic fatigue life estimation and strength reduction methods for thermal stress.

• 한국융합학회논문지
• /
• 제11권5호
• /
• pp.139-144
• /
• 2020

본 연구에서는 드럼자체와 브레이크에 대한 시뮬레이션 해석을 하였으며 열해석 결과와 구조 해석을 통한 내구성을 고찰하여 그 해석 결과를 얻었다. 브레이크 실린더로 인하여 힘을 받는 라이닝,라이닝의 확장으로 인하여 힘을 받는 드럼 내부, 축의 회전으로 인하여 힘을 받는 드럼에 대한 열응력 및 구조 해석을 통하여 어느 부분에 등가응력과 변형량이 큰지를 확인하였다. 본 연구 결과를 종합하여 브레이크 디스크설계에 응용한다면 열변형 방지 및 그 내구성을 증대시키는데 활용성이 클 것으로 사료된다. 본 연구 결과는 실제적으로 드럼 브레이크에서의 열응력에 견딜 수 있는 내구성 있는 설계에 유용하게 적용할 수 있다. 계절별 기차선로 이음새에서의 내구성 해석을 적용함으로서 본 연구 결과가 미적인 설계에 응용되는 융합 연구에 유리하다고 보여진다.

• 한국군사과학기술학회지
• /
• 제23권5호
• /
• pp.435-443
• /
• 2020

Thermal barrier coating(TBC) applied to fighter and turbine engines is a technology that improves the durability of core parts by lowering the surface temperature of base material. The thermal stress caused by mis-match of the coefficient of thermal expansion between the top coating and the TGO interface is the main cause of TBC breakage. Since the thermal stress is dependent on the microstructure of the TBC, designing microstructure of TBC can improve the durability as well as lower the thermal stress. In this study, the effect of coating thickness, volume of porosity and vertical cracking on the thermal stress was analyzed through finite element analysis. Through the analysis results, a design range of a microstructure that can improve the durability of thermal barrier coating by lowering thermal stress is proposed.

• 한국기계가공학회지
• /
• 제16권3호
• /
• pp.82-87
• /
• 2017

This study investigates thermal deformation due to fan shape of a hair dryer. In this study, thermal analysis showed that the shape of an electric fan results in lower temperature than that of a sieve frame. Among the shapes of electric fans, the temperature change decreases as the number of wings decreases. As a result of thermal deformation, model 4 (sieve frame shape) showed increased change of deformation compared to models 1, 2, and 3 (with electric fan shapes). Thus, the model 1 dryer with the sieve frame shape is shown to have the least durability among models 1, 2, 3, and 4. It is thought that the analysis results of this study can be applied to durability improvement and safer design of hair dryers.